Phantom Cables CA-NDB313-W User manual

Wi-Fi Video Doorbell
CA-NDB313-W
Quick Start Guide

Quick Setup
Power Kit Installation
Doorbell Installation
Doorbell Setup

1
What's in the Box
Doorbell (x1)
Faceplate (x3)
Pick the one that
best matched
your home from
three faceplates.
Mounting Plate (x3)
Pick the one for best
surveillance angle.
Screwdriver (x1)
Plate Foam (x1)
Stabilize the
mounting plate when
installing it in the
rough surface. Drill Bit (x1)
Power Kit (x1)
Wire Harness (x1)
Fuse Wire (x1)
Wire Connectors (x4)
Mounting Screws (x3)
Anchors (x3)
Mini-Level (x1) U-shaped Wires (x2)
Security Screws (x2)
Fixing Screws (x2)
Doorbell Screws (x2)
Tools You May Need
Drill Pencil

2
1Shut off the electricity at the breaker that controls
doorbell's circuit. 2 Insert one end of the wire harness the power kit.
3 Remove the cover from your mechanical chime. 4Remove the existing chime wires in the terminals
named TRANS and FRONT.
TRANSF RONTREAR REAR
Power Kit Installation
•If you have mechanical chime installed in your home, install the power kit and doorbell.
•If you have electronic chime installed in your home, refer to its own manual to install the power kit, and install
the doorbell.
•If no chime is installed, skip power kit installation, install the doorbell and follow the Option B in page 5.

3
5Connect the wire harness to the chime's terminals
named TRANS and FRONT. 6Insert the existing chime wire and the other end of the wire harness into the wire connector and twist it tightly.
Repeat this step with the other chime wire.
Wire
Connector
Wire Harness
Chime Wire
Wiring Overview
DO NOT OIL
TRANS FRONTREAR
TRANS FRONTREAR
Chime Wire
Chime Wire
7Mount the power kit to the side of the chime. 8Put back the chime cover.

4
Recommended Installation Height: 4 feet (1.2 m) above the ground.
1Shut off the electricity at the breaker that controls
doorbell's circuit. 2(Optional) When the wall is uneven, paste the plate
foam to the mounting plate.
3Insert the mini-level into the mounting plate and mark
the drill points when its bubble stays in the middle.
Mini-Level
Remove the mini-level when drill points are marked.
4Drill holes according to drill points and insert anchors.
Anchor
Recommended Hole Depth: 1 inch to 1.2 inch (25 to 30 mm).
Doorbell Installation

5
5Fix the mounting plate to the wall.
Mounting Screw
6Remove faceplate on your doorbell from buttom to top.
7If you have a chime installed, follow Option A; If not, follow Option B.
Option A Connect doorbell with your existing doorbell wires.
U-Shaped Wire
Fixing Screw
Option B Connect the fuse wire with your existing doorbell wire.
Fixing Screw Fuse Wire
Power Supply: 8 to 24 VAC

6
8Fix the doorbell to the mounting plate by inserting the
doorbell screws.
Doorbell Screw
9Restore the electricity at the breaker.
•Doorbell is powered on when its indicator flashes blue quickly. If not, make sure your electricity is
off and check the wiring. If yes, proceed to doorbell setup.
•For the first time use, please power on the doorbell and wait for 3 hours before using it, or else the
chime in your home may not work.
1Add to app.
-Connect your mobile phone to Wi-Fi.
-Download and install the app.
-Register a user account following the start-up wizard and log in.
-On the Home screen, tap “+” on the upper-right corner to go to the scan QR code page.
-Scan the QR code on the device or the cover of this manual when the indicator flashes blue.
-Follow the app wizard to finish Wi-Fi configuration.
If you want to change your doorbell's Wi-Fi, press and hold the reset button for 5s and repeat this part.
Doorbell Setup

7
2Put the faceplate back and insert two security screws into the bottom of the doorbell to secure the faceplate.
Security Screw
Appendix
Basics
Mounting Holes Terminals
micro SD Card
Slot
Reset Button
Hold for 5s to reset and
enter to AP mode.
LED Indicator
Blue Light Flashing Doorbell is ready for Wi-Fi configuration.
Steady on Doorbell is working.
Red Light Flashing Fast Device Exception
Steady on Doorbell is powering on.

8
Use AP Mode for Wi-Fi Configuration
-For AP hotspot configuration, press the Reset button for 5seconds and then you will hear voice prompt.
-Wait for a few seconds until you see the LED indicator flashes blue.
-Follow the voice prompt to connect Wi-Fi.
Wi-Fi Name: softap_XXXXXXXXX (9-digit Serial No.)
Default Password: softap_XXXXXX (Verification Code)
eg. Default Password: softap_ABCDEF
Serial No. and verification code are listed on the cover of this manual.
-Go back to app after successful connection. Tap Next.
-Search out the Wi-Fi you want the device to connect and enter password.
SD Card Management
1. In the app, tap the Storage Status in the Device Settings interface to check the SD card status.
2. If the card status displays as Uninitialized, tap to initialize it.
The status will then change to Normal and it can store videos and/or pictures.