Philio Technology Corporation PSR07 User manual

PSR07 Smart Color Button
This device is a multiple functions button switch. It is able to
switch the appliances on/off or adjust the percentage of dimmer.
It can also work as a timer. The well designed wall bracket and
magnetic back let the switch can be fixed on the wall. This product
can be included and operated in any Z- aveTM network with other
Z- aveTM certified devices from other manufacturers and/or other
applications.
Note:
Please provide a 5 DVC voltage through Micro SB Port to
wake the device up before the first using.
The rotation function and timer functions work only when the
device is fitted upright or stick on the wall or the device will only
work as an on/off switch when fitted horizontal.
Z-Wave Network Setting p
In the first time, add the device into the Z- aveTM network. Make
sure the primary controller is in the add mode. And then power on
the device through micro USB. The device will auto start the N I
(Network ide Inclusion). Red LED will flash every second and
continue 30 seconds. And it should be included in 5 seconds. Red
LED will light ON one second. Rotating to area A(shown in Fig. 1)
and touch 3 times can abort N I mode.
There is a touch button on the front side. The button carries out
manual inclusion, exclusion and reset to default.
1. Include: Pointing the arrowhead to area A first (shown in Fig.
1). Pressing the button three times within 1.5 seconds. The red
LED will light up for 1 second if succeed.
2. Exclude: Pointing the arrowhead to area A first. Pressing the
button three times within 1.5 seconds.
3. Reset to default: Pointing the arrowhead to area A first.
Pressing button four times within 2 seconds and hold at fourth.
The red LED will light for 3 seconds, release the button within
2 seconds while the LED goes out. The LED will flash for 1
second if reset succeed, or LED will flash once.
Notice: Including a node ID allocated by Z- aveTM Controller
means “Add” or “Inclusion”. Excluding a node ID allocated by
Z- aveTM Controller means “Remove” or “Exclusion”.
Function
This device can control dimmers in group 2 using three ways:
Dimmer, Timer, and Binary Switch. Point the arrowhead to area
A(shown in Fig. 1 and Fig. 2) then hold the button, release after
the red LED go out. One beep means entering Timer mode or two
beeps means entering Dimmer mode. The device can switch to
Binary Switch mode automatically when fitting horizontal.
1

*Dimmer
This device is able to set dimmer level by rotating to different
angle. hen the status is Off, surround LED will not work except
in area A(shown in Fig. 1). Rotate the device to area B, C,
D(shown in Fig. 1) then touch the button can set the status to On.
After a short beep, the surround LED will change gradually from
blue to red and send different level to group 2 in area B when
rotating. To turn Off the device in group 2, you can rotate PSR07
to area C or touch the button again.
*Timer
This mode can time the length of turning Off the light. The length
is up to 15 minutes. hen counting down starts, surround LED will
flash and buzzer will sound according to the remaining time.
Rotating to area C can cancel counting down directly.
Timer left Flash color Buzzer
10~15 minutes Cyan / 10 seconds
5~10 minutes Green / 10 seconds
3~5 minutes Yellow / 10 seconds
1~3 minutes Orange / 10 seconds
30~60 seconds Pink /10 seconds
10~30 seconds Pink /10 seconds 1 beep / 10 seconds
1~5 seconds Pink / 1 second 1 beep / 1 second
Time' up hite / 1 second 4 beeps / 1 second
2
Figure 1
Figure 2

*Binary Switch
This device is able to work as an On/Off state switch by pressing
the touch button when fitting horizontal.
Association
This device supports 2 association groups which every group has
eight node support.
To build/disable association between devices,
1. Have the Z- ave controller entered association mode.
2. Rotate PSR07 to area A then touch the button.
Group 1 is for receiving the report message, like the battery level.
Group 2 is for light control, the device will send Basic Set
command to this group.
Timing Report
The device supports the timing unsolicited report of the status.
• Battery level report: Every 6 hours report once in default.
It could be changed by setting the configuration NO. 10.
• Low battery report: hen the battery level is too low, every 30
minutes will report once.
Z-WaveTM Notification
After the device adding to the network, it will wake-up once per
day in default. hen it wake-up it will broadcast the “ ake Up
Notification” message to the network, and wake-up 10 seconds for
receive the setting commands. The wake-up interval minimum set-
ting is 30 minutes, and maximum setting is 120 hours. And the in-
terval step is 30 minutes. If the user want to wake-up the device
immediately, please rotate to area A and pressing the touch but-
ton once. The device will wake-up for 10 seconds every single
time.
Configuration
NO. Name Size
(Byte)
Def. Valid
Values
Description
1 Basic Set
OFF level
1 0x00 0x00~0x63
Control the value represented
by the left-side in area D.
E.g. Setting this configuration
to 0x0F means range of
Command Basic Set value
start from 0x0F
2 Basic Set
ON level
1 0x63 0x00~0x63
Control the value represented
by the right-side in area D.
E.g. Setting this configuration
to 0x1E means range of
Command Basic Set value
start from 0x1E
10
Auto
Report
Battery
Time
1 12 1~127
The interval time for auto re-
porting the Battery level. 0
means turn off auto report
battery.
The default value is 12.
25
Dimmer
Set
Method
1 0x00 0x00,0x01
Dimmer setting method.
0 : Auto send Command Ba-
sic Set after rotating.
1 : Send Command Basic Set
by touching key after rotating
Installation
1. Fix the bracket on the wall.
2. There's a magnet on the backside of this device. It can stick to
the bracket.
Notice: Do not install the bracket on unstable wall, this
may cause miscarriage to control lights.
3

Firmware update over the air (OTA)
This device supports the Z- ave firmware update via OTA. Let the
controller into the firmware update mode, and rotate to area A
then touch the button once to start update. After finish the
firmware download, the red LED will start to flash every 0.5 sec-
ond. Please don't remove the battery before the LED stop flashing.
Notice: recommend using OTA when the device is charg-
ing.
Supported Z-Wave Command Classes
* COMMAND_CLASS_Z AVEPLUS_INFO_V2
* COMMAND_CLASS_BATTERY
* COMMAND_CLASS_CENTRAL_SCENE_V1
* COMMAND_CLASS_VERSION_V2
* COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
* COMMAND_CLASS_DEVICE_RESET_LOCALLY
* COMMAND_CLASS_ASSOCIATION_V2
* COMMAND_CLASS_ AKE_UP_V2
* COMMAND_CLASS_ASSOCIATION_GRP_INFO
* COMMAND_CLASS_PO ERLEVEL
* COMMAND_CLASS_MULTI_CMD
* COMMAND_CLASS_SECURITY
* COMMAND_CLASS_FIRM ARE_UPDATE_MD_V2
* COMMAND_CLASS_CONFIGURATION
Security Network
The device support the security function. hen the device
included with a security controller, the device will auto switch to
the security mode. In the security mode, the follow commands
need using Security CC wrapped to communicate, otherwise it will
not response.
COMMAND_CLASS_BATTERY
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_ AKE_UP_V2
COMMAND_CLASS_CENTRAL_SCENE
Troubleshooting
Symptom Cause of Failure Recommendation
The switch
on/off
function not
working and
LED off
1. Battery is running
out of power
2. rong function
mode
1. Charging the battery by
Micro USB.
2. Pointing the arrowhead to
area B and press the
touch button.
3. If the device still can
work, don’t open up the
Switch and send it for
repair.
Can not
adjust the
percentage
of dimmer
1. The device may not
be placed upright.
2. The device is in off
state.
1. Check if the device is
placed upright.
2. Rotating to the
percentage you want
then press touch button.
Or pointing the
arrowhead to area B and
press the touch button to
turn the lamp on then
adjust the percentage.
The device
can not join
to Z- ave
network
1. The device may in a
Z- ave network.
2. The arrowhead
points to wrong
area.
1. Exclude the device then
include again.
2. Pointing the arrowhead to
area A then include
again.
4

Button no
response
1. The button will no
response when LED
is flashing.
ait for the LED go out and
try again.
Specification
Operating Voltage 3.7 V (Lithium Polymer Battery)
Low Battery Voltage 3.6 V
Battery Charge Voltage Vdc @ Micro USB Port
RF Range Minimum 40 m in door, 100m outdoor line
of sight
Operating Temperature -10°C ~ 4 °C
Frequency Range PSR07 (EU): 868.40MHz; 869.8 MHz(EU)
PSR07 (US): 908.40MHz;
916.00MHz(USA/Canada) /
PSR07 (TW/JP): 922. MHz/ 923.9MHz/
926.3MHz (Taiwan/JP)
RF Maximum Power + dBm
** Specifications are subject to change and improvement without
notice.
Disposal
This marking indicates that this product should not be
disposed with other household wastes throughout the
EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device,
please use the return and collection systems or
contact the retailer where the product was purchased.
They can take this product for environmental safe
recycling.
Company of License Holder：Philio Technology Corporation
Address of License Holder：8F.,No.653-2,Zhongzheng Rd.,
Xinzhuang Dist., New Taipei City 24257,Taiwan(R.O.C)
FCC Interference Statement
This equipment has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the in-
structions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in
a particular installation.
If this equipment does cause harmful interference to radio or tele-
vision reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the fol-
lowing measures:
• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is
subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user's au-
thority to operate this equipment.
This transmitter must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.
6