Philips SBCSC477/05 User manual

Instructions for use
English 4
Instructions pour l’utilisation
Français 15
Modo de empleo
Español 26
Bedienungsanleitung
Deutsch 37
Gebruiksaanwijzing
Nederlands 48
Istruzioni per l’uso
Italiano 59
Instruções de uso
Português 70
 
 81
Bruksanvisning
Svenska 92
Vejledning
Dansk 103
Bruksanvisning
Norsk 114
Käyttöohje
Suomi 125
baby monitor
SC477 DECT
SBC
XP SBC SC 477.1 Mediaware 13-11-2002 16:07 Pagina 1

2
☎Helpline
België & Luxemburg/
Belgien & Luxemburg/
Belgique & Luxembourg
(Belgium & Luxembourg)
Tel: [phone]
Danmark (Denmark)
Tlf: 808 82814
Deutschland (Germany)
Phone: [phone]
España (Spain)
Phone: [phone]
France
Phone: [phone]
 (Greece)
Phone: [phone]
Ireland
Phone: [phone]
Italia (Italy)
Phone: [phone]
Nederland (Netherlands)
Phone: [phone]
Norge (Norway)
Phone: [phone]
Österreich (Austria)
Phone: [phone]
Portugal
Phone: [phone]
Schweiz/ Suisse/ Svizzera
(Switzerland)
Tel.: [phone]
Suomi (Finland)
puh. 09 615 80 250
Sverige
Phone: [phone]
UK (United Kingdom)
Phone: [phone]
BE ✔DK ✔GR ✔ES ✔FR ✔
IRE ✔IT ✔LU ✔NL ✔AT ✔
PT ✔FI ✔SE ✔UK ✔NO✔
DE ✔CH ✔
SBC SC477 /00 /05 /84 /00H /05H /84H
R&TTE Directive 1999/5/EC
XP SBC SC 477.1 Mediaware 13-11-2002 16:07 Pagina 2

3
TALK
MONITORINTERCOM
OFF
DC9V
LIGHT
SYSTEM
1
3
4
5
6
7
9
8
10
11
2
CHARGE
DC9V
LEVEL
SYSTEM
POWER
TALK
PARENTVOLSENSIVITY
BABYVOL
13
12
14
15
16
17
18
20
21
22
23
26
25
24
19
A) Baby Unit
B) Parent Unit
XP SBC SC 477.1 Mediaware 13-11-2002 16:07 Pagina 3

ENGLISH4
Your baby monitor
SBC SC477
Philips is dedicated to producing caring, reliable products that new moms
and dads really need. Products whose reliability and operating quality bring
reassurance.You can trust this Philips baby monitor to provide round-the-
clock support by ensuring you can always hear your baby clearly, no matter
where you are in the house.
Philips Baby Care,Taking care together
Important information
Please read this guide carefully before using the baby monitor, and keep it
for future reference.This baby monitor is intended as an aid. It is not a
substitute for responsible and proper adult supervision and should not be
used as such.
•Make sure the Baby Unit and adapter cable are always out of reach of the
baby, at least one metre away.
•Never place the Baby Unit inside the baby ’s bed or playpen!
•Never cover the baby monitor (with a towel, blanket, etc.).
•Clean the baby monitor with a damp cloth.
•Never use the baby monitor near water.
Safety precautions
•Check if the voltage indicated on the type plate of the adapters
correspond to the local mains voltage before connecting to the mains
power supply.
•Do not use the set in moist places or close to water.
•Do not expose the set to extreme heat or light.
Contents
Help line 2
General 4
Important information 4
Product illustration on inside flap 5
Getting the baby monitor ready 6
Monitoring your baby 8
Using the family intercom system 9
Explanation of features 11
Problem solving 12
Technical specifications 13
Resetting to default factory settings 14
XP SBC SC 477.1 Mediaware 13-11-2002 16:07 Pagina 4

Product illustration on inside flap
A) Baby Unit
1night light button
2night light
3TALK button
4battery check light lights red when battery power is low
5DECT system check light
blinks red: connection not OK
lights red: no connection for more than 2 minutes,
the system check alarm on the Parent Unit beeps
blinks green: searching for connection
blinks green fast: transmitting sound
lights green: connection OK
6 loudspeaker
7microphone
8MONITOR / INTERCOM power on switch
9 battery compartment cover
10 DC power supply socket
11 AC power adapter
B) Parent Unit
12 sound-level lights
13 battery check light lights red when battery power is low
14 DECT system check light
blinks red: connection not OK
lights red: no connection for more than 2 minutes,
the system check alarm on the Parent Unit beeps
blinks green: searching for connection
blinks green fast: transmitting sound
lights green: connection OK
15 TALK button
16 microphone
17 loudspeaker
18 POWER button
Single Point Control
19 mode switch selects Parent Vol(ume), Baby Vol(ume) and
Baby Sensitivity
20 up (+)/down (-) adjusts sensitivity and volume of selected unit
21 charging base
22 charging light
23 DC power supply socket
24 AC power adapter
25 belt clip
26 battery compartment cover
ENGLISH 5
XP SBC SC 477.1 Mediaware 13-11-2002 16:07 Pagina 5

Getting the baby monitor ready
Baby Unit
For your convenience the Baby Unit can be mains or battery operated.
Mains operated use
1Connect the AC power adapter (11) to a mains socket and the cord to
the DC power supply socket (10) of the Baby Unit.
2The Baby Unit is now ready for mains operated use.
Battery operated use
1Remove the battery compartment cover (9).
Push on the round part, keep it down and slide the cover downwards.
2Insert four 1.5V, LR6 (AA) Alkaline batteries noting the + and -
configuration inside the battery compartment.
(The batteries are not included; we recommend non-rechargeable Philips
Alkaline batteries).
3Put the battery compartment cover back in place. Put the cover on the
compartment and slide the cover upwards until it clicks.
4The Baby Unit is now ready for battery operated use.
The Baby Unit operates for up to 30 hours on fresh batteries
(Philips Alkaline batteries, Baby night light switched off).
5When the battery check light (4) flashes red, the battery power is low.
Install new batteries if this happens.
Tips:
–Switch off the Baby night light to save battery power, when the Baby Unit is
battery operated.
–Remove empty batteries from the Baby Unit.
Battery back-up
As soon as the batteries are inserted battery back-up will be activated. In
case of mains failure during mains operated use the unit will automatically
switch to battery operated use.As soon as the mains supply is back on
the unit switches to mains operated use again.
Parent Unit
The Parent Unit comes with and uses high performance rechargeable
battery pack.The battery pack must first be inserted and charged before
the Parent Unit can be used outside the charging base (21).
Note: Never operate the Parent Unit without a battery pack!
Without the battery pack, the unit might not work correctly.
T
ERCOM
DC 9V
TALK
MONITORINTERCOM
OFF
DC9V
DC9V
TALK
MONITORINTERCOM
OFF
DC9V
DC9V
ENGLISH6
XP SBC SC 477.1 Mediaware 13-11-2002 16:08 Pagina 6

Mains operated use / charging the battery pack
1Remove the battery compartment cover (9).
Push on the round part, keep it down and slide the cover downwards.
2Insert the battery pack (without the battery pack, the unit might not work
correctly):
Plug the connector of the cable into the connector on the left side of the
battery compartment.
Place the side with the connection cable in the top of the battery
compartment.
3Put the battery compartment cover back in place. Put the cover on the
compartment and slide the cover upwards until it clicks.
If the rechargable battery pack begins to lose its effectiveness, replace it with
a new battery pack. Use rechargeable NiMH battery packs only!
4Connect the AC power adapter (24) to a mains socket and the cord to
the DC power supply socket (23) of the charging base.
5Place the Parent Unit inside the charging base.
The red charging light (22) lights.
The Parent Unit can be operated now, but you should leave it in the
charging base until the battery pack is fully charged (at least 14 hours).
When the battery pack is fully charged, the Parent Unit can be taken out of
the charging base and used cordlessly for up to 16 hours.
When the battery check light (13) flashes red, the battery power is low.
Place the Parent Unit inside the charging base to recharge the battery pack.
Note: Never operate the Parent Unit without a battery pack!
Without the battery pack, the unit might not work correctly
Disposal of batteries
Dispose of used batteries in an environmentally friendly manner.
Do not mix old and new batteries, or different types of batteries.
Remove Baby Unit batteries if the baby monitor is not to be used for
long periods.
ENGLISH 7
DC9V
CHARGE
POWER
TALK
PARENTVOLSENSIVITY
BABYVOL
TALK
PARENTVOLSENSIVITY
BABYVOL
TALK
LSENSIVITY
Y
VOL
XP SBC SC 477.1 Mediaware 13-11-2002 16:08 Pagina 7

Monitoring your baby
Switching on the units
1Position the Baby Unit at least one metre away from your baby.
Never place the Baby Unit inside the baby ’s bed or playpen.
2Set the MONITOR/INTERCOM power on switch (8) on the Baby Unit to
MONITOR.
> The DECT system check light (5) blinks (green).
3Switch on the Parent Unit by pressing the POWER button (18).
> The DECT system check light (14) blinks (green).
> DECT system check lights of Baby Unit and Parent Unit light continuously
(green) when both units have established a connection.
Note:The Parent Unit beeps when it is (accidentally) switched off.
Adjusting loudspeaker volume
Parent Unit
1Set the Single Point Control mode switch (19) on the Parent Unit to
PARENT VOL.
2Press the Single Point Control +/- button (20) on the Parent Unit to
increase/decrease the loudspeaker volume of the Parent Unit.
> The sound-level lights (12) on the Parent Unit give visual feedback about
the setting for approximately 3 seconds.
0 lights = monitoring baby silently
5 lights = maximum
Note:A high pitched noise may occur in case the units are too close to each
other.To avoid this you should set the Parent Unit volume to 0 before
placing the units close to each other.
Baby Unit
3Set the volume/sensitivity selection switch (19) on the Parent Unit to
BABY VOL.
4Press the Single Point Control +/- button (20) on the Parent Unit to
increase/decrease the loudspeaker volume of the Baby Unit.
> The sound-level lights (12) on the Parent Unit give visual feedback about
the setting for approximately 3 seconds.
0 lights = speaker off
5 lights = maximum
Note:You can only change the Baby Unit volume if the connection between the
Baby Unit and Parent Unit is established.
PARENT VOLSENSIVITY
BABY VOL
PARENT VOL SENSIVITY
BABY VOL
LEVEL
SYSTEM
POWER
MONITORINTERCOM
OFF
ENGLISH8
PARENT VOLSENSIVITY
BABY VOL
PARENT VOL SENSIVITY
BABYVOL
XP SBC SC 477.1 Mediaware 13-11-2002 16:08 Pagina 8

Adjusting microphone sensitivity
1Set the Single Point Control mode switch (19) on the Parent Unit to
BABY SENSITIVITY.
2Press the Single Point Control +/- button (20) on the Parent Unit to
increase/decrease the microphone sensitivity of the Baby Unit.
> The sound-level lights (12) on the Parent Unit give visual feedback about
the setting for approximately 3 seconds.
0 lights = minimum level
5 lights = maximum level (continuous transmission)
Note:When set to maximum level (continuous transmission), the Baby Unit
monitors continuously and all sounds, regardless of level, can be heard on
the Parent Unit. Battery operating time may decrease to approximately
8 hours during continuous transmission.
Note:You can only change the Baby Unit sensitivity if the connection between
the Baby Unit and Parent Unit is established
Using the family intercom system
Talking back to comfort your baby
1Set up both units to MONITOR your baby’s sounds.
2Adjust the loudspeaker volume level of the Baby Unit, using the Single Point
Control switch and buttons, to a level you prefer.
3On the Parent Unit, press and hold the TALK button (15) and talk clearly
into the microphone.
While the TALK button on the Parent Unit is being pressed, no sounds from
the Baby Unit can be heard on the loudspeaker of the Parent Unit.
Note:Wait with talking until the system check light is blinking green.
Note: In case the loudspeaker volume of the Baby Unit is set to 0 the system
check light will light red, while pressing the TALK button.
4Release the TALK button when finished.
LEVEL
SYSTEM
POWER
PARENT VOL SENSIVITY
BABY VOL
ENGLISH 9
PARENT VOL SENSIVITY
BABY VOL
XP SBC SC 477.1 Mediaware 13-11-2002 16:08 Pagina 9

Tw o way intercom
Your SBC SC477 is suited for use as a two-way intercom.
1Set the MONITOR / INTERCOM power on switch (8) on the Baby Unit
to INTERCOM.
> The DECT system check light blinks (green).
2Switch on the Parent Unit by pressing the POWER button.
3Wait for an established connection (system check lights green).
4Adjust the loudspeaker volume level of the Baby Unit to a level you prefer.
5Adjust the loudspeaker volume level of the Parent Unit to a level you
prefer.
6On the Parent Unit, press and hold the TALK button (15) and talk clearly
into the microphone.
Note:Wait with talking until the system check light is blinking green.
Note: In case the TALK button is pressed on the Parent Unit, and the
loudspeaker volume of the Baby Unit is set to 0, the system check lights
will light red.
Note: In case the TALK button is pressed on the Baby Unit, and the loudspeaker
volume of the Parent Unit is set to 0, the Parent Unit will beep to indicate
this.
7Release the TALK button (15) when you are finished.
8On the Baby Unit, press and hold the TALK (3) button and talk clearly
into the microphone.
9Release the TALK (3) button when you are finished.
While the TALK button on either unit is being pressed, a signal from the
other unit cannot be heard. In other words,only one person should speak
at a time.
LEVEL
SYSTEM
POWER
LEVEL
SYSTEM
POWER
SYSTEM
ENGLISH10
MONITORINTERCOM
OFF
XP SBC SC 477.1 Mediaware 13-11-2002 16:08 Pagina 10