Philips CSP1200 User manual

www.philips.com/welcome
Register your product and get support at
CSP1000 CSP1200
www.philips.com/welcome
Register your product and get support at
EN User manual

c
ab
A
a
b
B

10 ~ 15mm
10 - 15 mm
10 - 15 mm
10—15 мм
10 ~ 15 ߚା
Speaker wire
(not supplied)
Cable de altavoz (no incluido)
Cabo dos alto-falantes (não fornecido)
Кабель АС (не входит в комплект)
ၺඔ౸ྮӤຖݤ
Amplifier
Amplificador
Amplificador
Усилитель
ݡ૓ۄט౸
c
4a

(For CSP1200 only)
(Sólo para el modelo CSP1200)
(Somente para CSP1200)
(Только для модели CSP1200)
(仅限于 CSP1200)
Speaker wire
Cable de altavoz
Cabo dos alto-falantes
Кабель АС
ၺඔ౸ྮ
Amplifier
Amplificador
Amplificador
Усилитель
ݡ૓ۄט౸
Parallel connection 2Ω
Conexión en paralelo 2Ω
Conexão paralela 2Ω
Параллельное подключение 2Ω
并联 2Ω
Serial connection 8Ω
Conexión en serie 8Ω
Conexão serial 8Ω
Последовательное подключение 8Ω
串联 8Ω
Speaker wire
Cable de altavoz
Cabo dos alto-falantes
Кабель АС
ၺඔ౸ྮ
Amplifier
Amplificador
Amplificador
Усилитель
ݡ૓ۄט౸
4Ω
Speaker wire
Cable de altavoz
Cabo dos alto-falantes
Кабель АС
ၺඔ౸ྮ
Amplifier
Amplificador
Amplificador
Усилитель
ݡ૓ۄט౸
4b

*
*
*
*
*
*
*
*
*
*
e
a
b
C

English
1. Important
Safety
Read and understand all instructions before you use the apparatus.•
If damage is caused by failure to follow instructions, the warranty does
not apply.
Use only the supplied mounting hardware for a safe and secure•
installation.
Thesubwooferisheavy.Attachitrmlytoasolidthickbafe-board.•
Donotcontinuouslyusethespeakersystembeyondthepeakpower•
handling capacity.
Keep credit cards, watches, recorded tapes etc. with magnetic coding•
awayfromthespeakersystemtopreventdamagecausedbythe
magnetsinthespeakers.
Clean the apparatus with soft, damp cloth. Never use substances such•
as alcohol, chemicals or household cleaners on the apparatus.
Notice
Environmental information
Allunnecessarypackaginghasbeenomitted.Wehavetriedtomake
thepackagingeasytoseparateintothreematerials:cardboard(box),
polystyrenefoam(buffer)andpolyethylene(bags,protectivefoamsheet.)
Your system consists of materials which can be recycled and reused if
disassembled by a specialized company. Please observe the local regulations
regardingthedisposalofpackagingmaterials,exhaustedbatteriesandold
equipment.
Anychangesormodicationsmadetothisdevicethatarenotexpressly
approved by Philips Consumer Lifestyle may void the user’s authority to
operate the equipment.
2009©KoninklijkePhilipsElectronicsN.V.Allrightsreserved.
Specicationsaresubjecttochangewithoutnotice.TrademarksarethepropertyofKoninklijkePhilips
ElectronicsN.V.ortheirrespectiveowners.Philipsreservestherighttochangeproductsatanytime
withoutbeingobligedtoadjustearliersuppliesaccordingly.

Your car power subwoofer
Congratulations on your purchase, and welcome to Philips! To fully
benetfromthesupportthatPhilipsoffers,registeryourproductat
www.philips.com/welcome.
Introduction
Withthesubwoofer,youcanenjoyhighqualitysoundperformance
with powerful bass and beats.
What’s in the box A
Checkandidentifythecontentsofyourpackage:
aSubwoofer
b Screw_4x50mm(x10)
cFrame
2. Installation
Adepthofatleast124mmisrequiredtomountthesubwoofer.Measure
the depth of the area where you are to mount the subwoofer, and ensure
that the subwoofer does not obstruct any other components of the car.
Option 1: Mount on rear tray B
You can mount the subwoofer on the rear tray. a
1 Turnoffthecarignitionkey.
Ifthepowerison,theclicknoisegeneratedbytheconnection• maydamagethespeakers.
2Paste the supplied template onto the location for mounting the
subwoofer.
3 Markthecut-offholeandthe10boltholes. b

4 Cutoutthemarkedareaaanddrilltheboltholes. c
5 Connectthesubwoofertotheamplier. d
6 Mountthesubwooferintothereartraywiththesuppliedscrews. e
Option 2: Install in a sealed enclosure C
If the subwoofer cannot be mounted on the car, place it in a sealed
enclosure. a
1 Makeasealedenclosureindimensionasbelow:
The box:
CSP1000 CSP1200
Height 338mm 358mm
Length 522mm 568mm
Width 232mm 238mm
The mounting hole:
CSP1000 CSP1200
Mounting hole diameter (Outside) 257.3mm 307mm
Mounting hole diameter (Inside) 231.9mm 283.7mm
Screw hole diameter 3.3mm 3.3mm
2 Connectthesubwoofertotheamplier(seestep5of“Option1:
Mountonreartray”section).
3Install the subwoofer into the sealed enclosure with the supplied
screws. b
3. Product information
Note
Productinformationissubjecttochangewithoutpriornotice.
•

Model CSP1000 CSP1200
Speaker type 25cmsubwoofer 30cm subwoofer
RMS power (Watts) 250W 400W
Peak music power (Watts) 1000W 1600W
Sensitivity (dB/W/m) 88dB 89dB
Frequency response (Hz) 25-1000Hz 20-1500Hz
Impedance (ohms) 4 ohms 4 ohms
Magnet mass (Oz) 55.4Oz 55.4Oz
Mounting depth (mm) 124mm 146mm
4.Troubleshooting
Tokeepthewarrantyvalid,nevertrytorepairthesystemyourself.
If you encounter problems when using this apparatus, go to the Philips
website(www.philips.com/welcome).WhenyoucontactPhilips,ensure
that the apparatus is nearby and the model number and serial number
are available.

© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
CSP1000_1200_00_UM_V1.0