Philips HD8030 User manual

HD8030
HD8010
User manual
www.senseo.com/register
www.philips.com/senseo-sarista/support
4203_000_7242_2_DFU-Luxury_A5_v1.indd 1 1/9/13 1:37 PM

1
4203_000_7242_2_DFU-Luxury_A5_v1.indd 2 1/9/13 1:37 PM

HD8030, HD8010
ENGLISH 4
FRANÇAIS 29
NEDERLANDS 56
4203_000_7242_2_DFU-Luxury_A5_v1.indd 3 1/9/13 1:37 PM

4
Introduction
Congratulations on your purchase of a Philips SENSEO®SARISTA bean-
funnel coffeemaker and welcome to Philips! To fully benet from the support
that Philips offers, register your product at www.senseo.com/register.
The Philips SENSEO®SARISTA bean-funnel coffeemaker uses a Douwe
Egberts SENSEO®SARISTA bean-funnel to brew coffee from freshly ground
beans, which ensures optimal aroma and taste. Douwe Egberts SENSEO®
SARISTA bean-funnels are available in different varieties to suit different tastes.
This user manual applies to HD8030 and HD8010. HD8030 comes
standard with an insulated jug. For HD8010, you can buy an insulated jug as
an accessory in the online shop at www.shop.philips.com/service.
For more information on the Philips SENSEO®SARISTA bean-funnel
coffeemaker and for instruction movies on how to use the coffeemaker
and the bean-funnels, go to www.philips.com/senseo-sarista.
For support and movies on how to clean, maintain and descale the
coffeemaker and how to adjust the grinder, go to
www.philips.com/senseo-sarista/support.
General description (Fig. 1)
1 Activity light
2 ’Water tank empty’ light
3 CALC CLEAN light
4 ’Bean-funnel empty’ light
5 ’Coffee grounds container full’ light
6 Coffee strength button (HD8030 only)
7 1-cup button
8 Jug button
9 On/off button
10 2-cup button
11 Control panel
12 Coffee dispensing head
13 Water tank
14 Detachable coffee spout for 1 or 2 cups
15 Drip tray cover
16 ’Drip tray full’ indicator
17 Drip tray
18 Coffee grounds container
19 Coffee jug (HD8030 only)
20 Lid of coffee jug (HD8030 only)
21 Brewing unit
22 Service door
23 Grinding degree adjustment hole
24 Opening for bean-funnel
25 Grinding degree adjustment tool
26 Bean-funnel
Important
Read this user manual carefully before you use this coffeemaker and
save it for future reference. You can download the user manual and nd
instructions on how to clean, maintain and descale the coffeemaker and
adjust the grinder at www.philips.com/senseo-sarista/support.
ENGLISH
4203_000_7242_2_DFU-Luxury_A5_v1.indd 4 1/9/13 1:37 PM

Danger
- Never immerse the coffeemaker in water or any other liquid, nor rinse
it under the tap.
Warning
- Check if the voltage indicated on the coffeemaker corresponds to the
local mains voltage before you connect the coffeemaker.
- This coffeemaker can be used by children aged from 8 years and above
and by persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and if they
understand the hazards involved.
- Cleaning and user maintenance shall not be made by children unless
they are older than 8 and supervised.
- Keep the appliance and its cord out of the reach of children aged less
than 8 years.
- Children should be supervised to ensure that they do not play with the
coffeemaker.
- Keep the packaging materials (plastic bags, cardboard buffers, etc.) out
of the reach of children, as they are not a toy.
- This coffeemaker is designed to grind beans and brew coffee. Use it
correctly and with care to avoid scalding by hot water and steam.
- Do not use the coffeemaker if the plug, the mains cord or the
coffeemaker itself is damaged.
- If the mains cord is damaged, you must have it replaced by Philips, a
service centre authorised by Philips or similarly qualied persons in
order to avoid a hazard.
Caution
- Always place and use the coffeemaker on a stable, level and horizontal
surface.
- Unplug the coffeemaker if problems occur during grinding or brewing
and before you clean it.
- Do not move the coffeemaker while it is operating.
- Do not use the appliance in combination with a transformer, as this
could cause hazardous situations.
- If a problem occurs that you cannot solve by means of this user manual,
contact the Consumer Care Centre in your country. If the problem
cannot be solved, take the coffeemaker to a service centre authorised
by Philips for examination or repair. Do not attempt to repair the
coffeemaker yourself, otherwise your guarantee becomes invalid.
- None of the detachable parts, nor the jug is dishwasher-proof.
- Never use the jug in a microwave oven.
- Never immerse the jug in water or any other liquid, as this could cause
water to enter between the walls of the jug.
- Keep the jug away from heat sources to prevent damage.
- The inside of the jug is breakable. Do not put ice cubes or other solid
objects in the jug.
- Only use the jug to keep coffee hot. Do not use it to keep milk, baby
food or other food hot or cold.
- Do not use aggressive cleaning agents, solvents or chemicals to clean
the jug.
ENGLISH 5
4203_000_7242_2_DFU-Luxury_A5_v1.indd 5 1/9/13 1:37 PM

- Do not overll the jug.
- Always check the inside of the jug before use. If you detect any cracks
or damage, do not use the jug.
- Be careful not to drop the jug. If the jug has fallen while full, do not
pour out the contents to prevent injury.The inner wall of the jug may
be broken due to the fall.
- To prevent scalding, always pour contents into a cup and do not drink
directly from the jug.
- This coffeemaker is intended for normal household use only. It is not
intended for use in environments such as staff kitchens of shops, ofces,
farms or other work environments. Nor is it intended to be used by clients
in hotels, motels, bed and breakfasts and other residential environments.
- Never use accessories or parts made by other manufacturers or that
have not been specically recommended by Philips. Your guarantee will
become invalid if you use such parts or accessories.
- Never ll the water tank with warm, hot or sparkling water, as this may
cause damage to the water tank and the coffeemaker.
Compliance with standards
- This Philips coffeemaker complies with all standards regarding
electromagnetic elds (EMF). If handled properly and according to
the instructions in this user manual, it is safe to use based on scientic
evidence available today.
Before rst use
Installing the coffeemaker
Never install the coffeemaker in environments where the temperature
may drop to 0° or below. If the water inside the coffeemaker freezes, the
coffeemaker will be damaged.
Note: It is normal that there are some traces of coffee and water in the
coffeemaker when you use it for the rst time. This is because the coffeemaker
has been tested in the factory to make sure that it is in perfect working order.
We guarantee that your coffeemaker is brand-new.
1 Remove all packaging material from the coffeemaker.
2 Place the coffeemaker on a table or worktop away from the tap, the
sink and heat sources.
3 Leave a free space of at least 15cm above, behind and on both sides
of the coffeemaker.
ENGLISH6
4203_000_7242_2_DFU-Luxury_A5_v1.indd 6 1/9/13 1:37 PM

4 Slide the drip tray into the guiding grooves in the front of the
coffeemaker.
Note: Make sure the drip tray is fully inserted.
Never remove the drip tray when the coffeemaker is brewing coffee.
5 Slide the detachable coffee spout into the coffeemaker.
Placing and removing the bean-funnels
For more information on the bean-funnels and movies on how to place them
on the coffeemaker, go to www.philips.com/senseo-sarista/support.
1 Pull the vertical tear strip down to remove the protective sleeve of
the bean-funnel.
2 Pull the round AROMA LOCK®seal off the bean-funnel.
3 Insert the screw thread of the bean-funnel properly into the
opening in the top of the coffeemaker (1).Then turn the bean-funnel
clockwise to fasten it (2).
ENGLISH 7
4203_000_7242_2_DFU-Luxury_A5_v1.indd 7 1/9/13 1:37 PM

Preparing for use
Filling the water tank
Fill the water tank with fresh water before each use.
Note: The ‘water tank empty’ light goes on when there is not enough water in
the water tank to brew one cup of coffee.
1 Remove the water tank from the coffeemaker.
2 Rinse the water tank under the tap.
3 Fill the water tank with cold tap water up to the MAX indication.
Never ll the water tank with warm, hot or sparkling water, as this may
cause damage to the water tank and the coffeemaker.
4 Slide the water tank back into the coffeemaker.
Automatic rinsing cycle
To guarantee the perfect cup of coffee the coffeemaker uses water to
rinse the brewing system.This happens during the automatic rinsing cycle
when the coffeemaker has not been used for a longer period of time (20
hours) and before and after brewing each cup. A part of the water ows
through the internal system directly into the drip tray.
1 Insert the plug into the wall socket.
2 Place a cup on the drip tray cover.
3 Press the on/off button to switch on the coffeemaker.
ENGLISH8
4203_000_7242_2_DFU-Luxury_A5_v1.indd 8 1/9/13 1:37 PM

,The activity light starts ashing.
,After a brief heating-up time, water ows into the cup and the drip
tray via the spout and internal circuits. Empty the cup and the drip
tray into the sink.
,When the activity light lights up continuously, the automatic rinsing
cycle is nished and the coffeemaker is ready for use.
Using the coffeemaker
Brewing 1 or 2 cups of coffee
1 Check if there is enough water in the water tank. Fill the water tank
with water, if necessary (see chapter ‘Preparing for use’).
2 Make sure the bean-funnel is attached properly (see chapter ‘Before
rst use’).
3 Empty the drip tray if the ‘drip tray full’ indicator is visible.
Note: If you ignore the ‘drip tray full’ indicator, the drip tray may overow
during brewing and water may end up under the appliance.
4 Place 1 or 2 cups on the drip tray cover.
5 Press the 1-cup or 2-cup button.
Tip: You can interrupt the brewing cycle at any time, which can give you a
stronger coffee. To do this, press the same cup button (1-cup button or 2-cup
button) that you pressed to start brewing coffee.
Note: Each cup of coffee is brewed from freshly ground beans.
ENGLISH 9
4203_000_7242_2_DFU-Luxury_A5_v1.indd 9 1/9/13 1:37 PM

- Press the 1-cup button to brew 1 cup of coffee.
,The coffeemaker grinds the required amount of coffee beans for one
cup and then brews one cup of coffee.
,The activity light ashes once when the beans are ground.
- Press the 2-cup button to brew 2 cups of coffee.
,The coffeemaker grinds the required amount of coffee beans for
one cup and then brews coffee lling both cups half. Then the
coffeemaker again grinds the coffee beans for one cup and brews the
coffee lling both cups fully.
,The activity light ashes once when the beans for the rst half are
ground and twice when the beans for the second half are ground.
Note: If the coffeemaker stops during brewing, the water tank or bean-funnel
may be empty or the coffee grounds container may be full. Fill the water tank,
replace the bean-funnel or empty the coffee grounds container and press
the 2-cup button again to complete the brewing cycle. Make sure the coffee
grounds container is taken out of the appliance for 3 seconds until the bean-
funnel empty light stops ashing, then place it back.
6 When the ‘bean-funnel empty’ light goes on, the bean-funnel is empty.
7 To replace the empty bean-funnel with a full one, turn the bean-
funnel anticlockwise (1) and remove it (2).Then perform step 1 to
place a new full bean-funnel on the coffeemaker.
Note: You can also remove a Douwe Egberts SENSEO® SARISTA bean-funnel
that is not yet empty and replace it with another one if you want to switch to
a different coffee blend. Because the bean-funnel is re-closed, you can store the
used bean-funnel for later use.
Never remove the bean-funnel when the coffeemaker is brewing coffee.
Brewing a jug of coffee
When you press the jug button, the coffeemaker brews six cups of coffee
into the jug.
Note: Always clean the jug with warm water and some washing-up liquid before
rst use. If you have not used the jug for a while, rinse it with warm water to
remove any odour.
1 Check if the water tank is lled to the MAX indication. Fill the water
tank with water, if necessary (see chapter ‘Preparing for use’).
Note: If you do not ll the water tank to the MAX indication, the ‘water tank
empty’ light may go on and the coffeemaker may stop during brewing. Fill the
water tank and press the jug button to continue brewing coffee.
MAX
ENGLISH10
4203_000_7242_2_DFU-Luxury_A5_v1.indd 10 1/9/13 1:37 PM

2 Make sure the bean-funnel is attached properly and contains enough
beans to brew a jug of coffee.
Note: The coffee beans have to be visible above the jug indication of the
bean-funnel. If this is not the case, there are not enough coffee beans in the
bean-funnel to brew six cups of coffee. Replace the bean-funnel with a full one
or one that contains enough coffee beans (see chapter ‘Before rst use’).
Note: If the bean-funnel becomes empty during brewing, the ‘bean-funnel
empty’ light goes on and the coffeemaker stops during brewing. Replace the
bean-funnel with a full one or one that contains enough coffee beans (see
chapter ‘Before rst use’) and press the jug button to continue brewing.
3 Remove the detachable coffee spout, if present.
4 Always empty the coffee grounds container and the drip tray before
you start brewing a jug of coffee.
Note: If you do not empty the drip tray, the drip tray may overow during brewing.
Note: If you do not empty the coffee grounds container, the ‘coffee grounds
container full’ light may go on and the coffeemaker may stop during brewing.
Make sure the appliance is switched on when you empty the coffee grounds
container. Take it out of the appliance for 3 seconds until the bean-funnel
empty light stops ashing before placing it back. Press the jug button to
continue brewing coffee.
5 Turn the lid of the jug by its lever to ‘closed/brewing’ position. In
this position, the arrowhead on the jug handle points to the ‘closed/
brewing’ symbol on the jug lid.
6 Place the jug on the drip tray cover.
Tip: To keep the coffee hot longer, rinse the jug with hot water to preheat it
before you start brewing coffee.
ENGLISH 11
4203_000_7242_2_DFU-Luxury_A5_v1.indd 11 1/9/13 1:37 PM

7 Press the jug button.
Note: Each cup of coffee is brewed from freshly ground beans.
,The coffeemaker grinds the required amount of coffee beans for the
rst cup of coffee and then brews coffee into the jug. The coffeemaker
grinds coffee beans and brews coffee ve more times to ll the jug.
,The activity light ashes once when the beans for the rst cup are
ground, twice when the beans for the second cup are ground etc.
,The coffeemaker automatically stops after brewing the sixth cup and
the activity light lights up continuously.
8 When the brewing cycle is nished, take the jug out of the
coffeemaker.
9 To pour out coffee, turn the lid to the ‘pour’ position. In this position,
the arrowhead on the jug handle points to the ‘pour’ symbol on the
jug lid.
Note: To keep the coffee in the jug hot, always turn the lid to the ‘closed/
brewing’ position immediately after pouring out coffee.
10 Empty the drip tray.
Selecting the coffee strength (HD8030 only)
The coffee strength button enables you to select the coffee strength you
prefer for each cup of coffee.
Note: You can only change the coffee strength when you are brewing 1 or
2 cups. The coffee strength button does not work when you are brewing a jug
of coffee. When you brew a jug, you get the standard coffee strength, which is
regular.
1 Press the coffee strength button one or more times to select the
strength you want.
,The corresponding coffee strength light goes on.
- e= strong short coffee
- d= regular coffee
- c= mild long coffee
Manual rinsing cycle
Next to the automatic rinsing cycle, you can also start a manual rinsing
cycle whenever you want.You may perform a manual rinsing cycle when
you switch to another variety. Rinsing enables you to enjoy the full aroma
of the coffee blend you have selected.
1 Ensure water tank is sufciently lled and activity light is on.
ENGLISH12
4203_000_7242_2_DFU-Luxury_A5_v1.indd 12 1/9/13 1:37 PM

2 Turn the bean-funnel anticlockwise to remove it.
3 Place a cup on the drip tray cover.
4 Press the 1-cup button to start the rinsing cycle.
Cleaning and maintenance
Never immerse the coffeemaker in water or any other liquid, nor rinse it
under the tap.
Always unplug the coffeemaker and let it cool down before you clean it.
Note: None of the detachable parts, nor the brewing unit and the jug are
dishwasher-proof, rinse them under the tap.
Cleaning the water tank, the coffee grounds container and the
drip tray
Empty and clean the water tank, the coffee grounds container and the drip
tray every day.Also empty and clean the water tank and coffee grounds
container when the ‘water tank empty’ light and/or the ‘coffee grounds
container full’ light go on. Empty and rinse the drip tray when the ‘drip tray
full’ indicator indicates the drip tray is full.
1 Remove the water tank from the coffeemaker.
ENGLISH 13
4203_000_7242_2_DFU-Luxury_A5_v1.indd 13 1/9/13 1:37 PM

2 Remove the lter from its holder in the water tank and rinse it
under the tap.
3 Clean the water tank with hot water and some washing-up liquid.
4 Place the lter back in its holder by turning it a little while pushing it
down gently.
5 Fill the water tank with fresh, cold tap water and slide it back into
the coffeemaker.
6 Remove the coffee grounds container from the coffeemaker and
empty it.
7 Clean the coffee grounds container with hot water and some
washing-up liquid.
8 Slide the coffee grounds container back into the coffeemaker.
9 Pull the drip tray out of the coffeemaker.
10 Remove the drip tray cover and empty the drip tray.
ENGLISH14
4203_000_7242_2_DFU-Luxury_A5_v1.indd 14 1/9/13 1:37 PM

11 Clean the drip tray and the drip tray cover with hot water and some
washing-up liquid.
12 Clean the guiding grooves for the drip tray in the bottom of the
coffeemaker with a moist cloth.
Cleaning the detachable coffee spout
1 Remove the detachable coffee spout.
2 Rinse the detachable coffee spout under the tap with some washing-
up liquid.
3 Slide the detachable coffee spout back into the coffeemaker or store it.
Cleaning the jug
Clean the jug after every use.
Do not use aggressive cleaning agents, solvents or chemicals to clean the jug.
1 Turn the lid by its lever to the ‘remove lid’ symbol to unlock the lid.
Then pull the lid off the jug.
2 Rinse the inside of the jug and the lid with warm water and some
washing-up liquid. Clean the outside of the jug with a damp cloth.
Note: The jug is not dishwasher-proof.
3 Put the jug in upright position without the lid on and let the inside of
the jug dry.
4 When the inside of the jug is dry, place the lid on the jug and turn it
to the ‘closed/brewing’ position
ENGLISH 15
4203_000_7242_2_DFU-Luxury_A5_v1.indd 15 1/9/13 1:37 PM

Cleaning the brewing unit
Do not clean the brewing unit in the dishwasher and do not use soap or
a cleaning agent to clean it.
Clean the brewing unit every time the bean-funnel is empty or at least
once a week. For more information on how to remove, clean and place
back the brewing unit, watch the instruction movies on
www.philips.com/senseo-sarista/support.
1 Switch off the coffeemaker and unplug it.
2 Remove the coffee grounds container from the coffeemaker.
3 Open the service door.
4 Press the PUSH button (1) and pull at the grip of the brewing unit
(2) to remove it from the coffeemaker.
5 Rinse the outside of the brewing unit under a lukewarm tap.
Never use any soap or other cleaning agent to clean the brewing unit.
Do not dry the brewing unit with a cloth to prevent bres from
collecting inside the brewing unit.After rinsing, just shake off excess
water.
6 Carefully rinse the upper lter under a lukewarm tap.
ENGLISH16
4203_000_7242_2_DFU-Luxury_A5_v1.indd 16 1/9/13 1:37 PM

7 Thoroughly clean the inside of the coffeemaker with a damp cloth.
8 Before you slide the brewing unit back into the coffeemaker, make
sure the two reference signs on the side match. If they do not match,
perform the following step:
- Make sure that the lever is in contact with the base of the brewing unit.
9 Make sure that the locking hook of the brewing unit is in the
correct position.The hook is not correctly positioned if it is still in
bottommost position.
- To position the hook correctly, push it upwards until it is uppermost
position.
ENGLISH 17
4203_000_7242_2_DFU-Luxury_A5_v1.indd 17 1/9/13 1:37 PM

10 Slide the brewing unit back into the coffeemaker using the guiding
rails on the sides until it clicks into position.
Do not press the PUSH button.
11 Close the service door.
Lubrication
For optimal performance of the coffeemaker, lubricate the brewing unit
after 400 cups of coffee or once a month.
- For more information on what and how to lubricate, watch the
instruction movies on www.philips.com/senseo-sarista/support.
- For optimal brewing results, we advise you to use the lubricant by
Philips.You can buy this lubricant in the online shop at
www.shop.philips.com/service.
1 Switch off the coffeemaker and unplug it.
2 Follow steps 2 to 4 of section ‘Cleaning the brewing unit’ to remove
the brewing unit from the coffeemaker.
3 Apply some lubricant to the guiding rails inside the brewing unit.
4
Apply some lubricant around the shaft in the bottom of the brewing unit.
ENGLISH18
4203_000_7242_2_DFU-Luxury_A5_v1.indd 18 1/9/13 1:37 PM

5 Apply some lubricant to the part shown in the gure.
6 Apply some lubricant on both sides of the lever in the brewing unit.
7 Follow steps 9 to 11 of‘Cleaning the brewing unit’ to place the brewing
unit and the coffee grounds container back into the coffeemaker.
Adjusting the grinding degree
Over time the grinder may change to a coarser setting. It is recommended
to adjust the grinding degree when you notice this.These adjustments are
not required regularly.
1 Take the grinding degree adjustment tool out of the recess next to
the brewing unit.
2 Insert the lug on the broad end of the grinding degree next to the
cap of the grinding degree adjustment hole and press lightly.This
makes the cap open automatically.
3 Insert the narrow end of the grinding degree adjustment tool into
the grinding degree adjustment hole so that the opening in the tool
ts onto the pin located at the bottom of the hole.
4 For a coarser setting, push down and turn the grinding degree
adjustment tool clockwise. For a ner setting, push down and turn
the grinding degree adjustment tool anticlockwise.
Note: Turn the grinding degree adjustment tool one step clockwise or
anticlockwise at the time. Then brew 2 or 3 cups of coffee to establish if the
grinding degree has been adjusted to your satisfaction.
5 When you are satised with the grinding degree, remove the grinding
degree adjustment tool from the grinding degree adjustment hole,
close the cap and place the grinding degree adjustment tool back
into its recess.
ENGLISH 19
4203_000_7242_2_DFU-Luxury_A5_v1.indd 19 1/9/13 1:37 PM

Descaling the coffeemaker
Scale builds up inside the coffeemaker during use. It is essential to descale the
coffeemaker when the CALC CEAN light is lit. Only use the special Philips
SENSEO®SARISTA descaling solution (CA6400) to descale the coffeemaker.
For more information on how to descale this coffeemaker, you can watch the
instruction movies on www.philips.com/senseo-sarista/support.
When to descale
- Descale the coffeemaker as described below as soon as
the CALC CLEAN light lights up continuously.
Why to descale
Your reasons to descale:
- It prolongs the life of your coffeemaker
- It ensures maximum cup volume
- It ensures maximum coffee temperature
- It prevents malfunctioning
If you do not descale the coffeemaker regularly or do not perform
the descaling procedure correctly, scale residue remains behind in the
coffeemaker.This causes scale to build up more quickly and will ultimately
stop your coffeemaker working properly. If this happens, repair is not
covered by the terms of the guarantee.
Descaling agent
Only use the special Philips SENSEO®SARISTA descaling solution
(CA6400) to descale the coffeemaker.This solution has been designed to
ensure continued good performance of your coffeemaker throughout its
operating life.
- You can buy Philips SENSEO®SARISTA descaling solution in the online
shop at www.shop.philips.com/service.
Keep the bottle with descaling solution out of the reach of children.
Never drink the water with descaling mixture that you pour into
the water tank or any water with residues that comes out of the
coffeemaker during the descaling procedure.
Descaling procedure
The descaling procedure lasts 45 minutes and consists of a descaling cycle
and two rinsing cycles. Do not interrupt the descaling cycle and do not
switch off the coffeemaker before you have performed the two rinsing cycles.
Before you start the descaling procedure make sure the activity light lights
up green continuously.To ensure this please make sure the following steps
are taken.
1 Make sure the bean-funnel is attached properly.
2 Empty the coffee grounds container.
3 Make sure the water tank is lled with water.
Note: Once you have started the descaling cycle, you are unable to exit before
the entire descaling procedure is complete. Even when you remove the plug the
machine will stay in the descaling cycle.
ENGLISH20
4203_000_7242_2_DFU-Luxury_A5_v1.indd 20 1/9/13 1:37 PM