Philips DVP620VR/17B Operating manual

There are many ways to connect your new DVD/VCR to your Television and other equipment.This Quick-Use
Guide shows the easiest, most common connection.
Higher quality connections are explained in the accompanying owner’s manual and will provide better sound or
picture if your TV and/or audio system is compatible.
REAR OF TV
(EXAMPLE ONLY)
ANTENNA IN
RF COAXIAL CABLE
IN OUT
CABLE BOX
(Optional)
CABLE TV SIGNAL
ANTENNA or
CABLE TV SIGNAL
1Disconnect all equipment from the power outlets. Connect the equipment to the power outlets only after you
have finished hooking up everything. Never make or change connections with equipment connected to the power outlet.
2Connect your Antenna TV signal directly to the AERIAL jack on the rear of the DVD/VCR using an RF cable
(not supplied).
If you have a Cable Box (or Satellite Receiver), connect the OUT jack of the Cable Box/Satellite Receiver to the
AERIAL jack on the DVD/VCR using an RF coaxial cable (not supplied).
3Connect the supplied black RF coaxial cable to the DVD / VCR’s ANT-OUT jack and to yourTV’s ANTENNA
IN jack. The TV’s ANTENNA IN jack may be labelled 75-ohm,TV IN, or RF IN. Check your TV manual for details.
4Plug the power cords of the DVD/VCR and the TV into an active power outlet.
5Turn on the TV power. Set the TV to a video channel. (If you cannot use channel 3 at your TV, you can use
channel 4 instead. However, you must correspondingly set the DVD/VCR’s output channel 3 or 4. See the
accompanying DVD/VCR owner’s manual for details.)
6Press the STANDBY-ON 2button on the DVD/VCR or its remote to turn on the DVD/VCR. The first
time you turn on the DVD/VCR, you should complete the VCR setup. See the other side of this Quick-
Use Guide for details.
DVP620VR
-
-
DVP620VR/17 QUG_rev2 28/05/2004 08:44 PM Page 1

STANDBY-ON
SOURCE
POWERON
VIDEO AUDIO REW F.FWD PLAY
RECORD CHANNEL VCR
OPEN/CLOSE
DVD STOP PLA
Y
ONETOUCH RECORDING • LONG PLAY
STOP/EJECT LR
STANDBY-ON
PLAY
DVDVCR VCR/TV
OK
MENU MENU
DISC/VCR
RETURN TITLE
A-B
CLEAR/RESET SLOW
SUBTITLE ZOOM ANGLE
REPEAT REPEAT AUDIO
SEARCH MODE DISPLAY
SKIP / CH
SYSTEM
PAUSESTOP
MARKER RECORDTIMER SET
SPEED
1 2 3
7
6
5
4
890
+10
Quick-Use Guide (cont’d)
Quick-Use Guide (cont’d)
Playing a Disc
1With the TV and DVD /VCR on, press the DVD
button to put the DVD / VCR in the DVD mode.
2Press OPEN/CLOSE /to open the disc tray.
Put a Disc in the tray with the label facing up and the shiny side
facing down.
Press OPEN/CLOSE /again to close the disc tray.
3Playback may start automatically. If not, press PLAY B.
If a DVD Disc menu appears, use the 1,2,3,4or Number
buttons to select features or start playback. Follow the
instructions in the menu.
4To stop playing a Disc, press STOP 9.
Setting Up the VCR the First Time
1Turn on the TV and set it to channel 3 or 4.
2Press VCR, then press STANDBY-ON 2.The VCR light will
appear on the front of the DVD/VCR. The display shown below
will appear.
3Press 3or 4to select English, French, or Spanish as the
language for VCR displays. Then, press 2.
4The AUTO SET UP message will appear. Press 2to set up TV
channels for the VCR. When setup is complete, the lowest TV
channel will appear on the TV.
AUTO SET UP
PUSH 2
LANGUAGE SELECT
2ENGLISH [ON]
FRANCAIS
ESPAÑOL
PUSH 2
Playable Discs
The DVD Player of the DVD/VCR will play the following Discs.
DVDs must have a Region Code of ALL regions or Region 1.
DVDs must be recorded in the NTSC or PAL Color System.Your TV
must also have the NTSC or PAL color system
1
ALL
Recordable
ReWritable
Turn on the TV to
channel 3 or 4.
3-4
2
1
2
STANDBY-ON
PLAY
DVDVCR VCR/TV
OK
MENU MENU
DISC/VCR
RETURN TITLE
A-B
CLEAR/RESET SLOW
SUBTITLE ZOOM ANGLE
REPEAT REPEAT AUDIO
SEARCH MODE DISPLAY
SKIP / CH
SYSTEM
PAUSESTOP
MARKER RECORDTIMER SET
SPEED
43
1
Remote Control
Setting
Before using the remote:
• Press ‘DVD’ for DVD
functions.
• Press ‘VCR’ for VCR
functions.
8239 300 31723
OVMN04133A/H9620UD***
DVP620VR/17 QUG_rev2 28/05/2004 08:44 PM Page 2