Philips HC7460 User manual

Register your product and get support at
www.philips.com/welcome
Always here to help you
HC7460

1
7
8
9
10
11
12
65
2
4
3
13
1

HC7460
ENGLISH 4
INDONESIA 11
한국어 19
BAHASA MELAYU 27
ภาษาไทย 35
TIẾNG VIỆT 42
繁體中文 49
简体中文 57

4
Introduction
Congratulations on your purchase and welcome to Philips!
To fully benet from the support that Philips offers, register your product
at www.philips.com/welcome.
General description (Fig. 1)
1 Cutting unit
2 Up button
3 Down button
4 On/off button
5 Length setting lock
6 Charging light
7 Display
8 Trimming comb 1-7mm
9 Trimming comb 7-24mm
10 Trimming comb 24-42mm
11 Adapter
12 Small plug
13 Cleaning brush
Important
Read this user manual carefully before you use the appliance and save it for
future reference.
Danger
- Keep the appliance and the adapter dry.
Warning
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
- Children should be supervised to ensure that they do not play with
the appliance.
Caution
- This appliance is not washable. Never immerse the appliance in water,
nor rinse it under the tap.
- Always check the appliance before you use it. Do not use the
appliance, adapter or any other part if it is damaged, as this may cause
injury.
- Always replace a damaged adapter or part with one of the
original type.
- Only use this appliance for its intended purpose as shown in the user
manual.
- Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the appliance.
ENGLISH

Electromagnetic elds (EMF)
This Philips appliance complies with all applicable standards and regulations
regarding exposure to electromagnetic elds.
General
- The appliance is equipped with an automatic voltage selector and is
suitable for mains voltages from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe low voltage of less
than 24 volts.
Charging
Charge the appliance fully before you use it for the rst time or after a long
period of disuse.
When it is charged for 1 hour, the appliance has a cordless operating time
of up to 120 minutes.
Note: After charging the appliance fully for the rst time, you can also use the
appliance directly from the mains. Simply connect the appliance to the mains.
Charging indications
Battery low indication
- When the battery is almost empty, the charging light starts to ash
orange.
Charging
- When the appliance is charging, the charging light ashes red.
Battery fully charged
- When the battery is fully charged, the charging light lights up red
continuously.
Note: After 30 minutes, the charging light switches off automatically.
Charging the appliance
1 Make sure the appliance is switched off.
2 Insert the small plug into the appliance.
3 Put the adapter in the wall socket.
4 After charging, remove the adapter from the wall socket and pull the
small plug out of the appliance.
ENGLISH 5

Optimising the lifetime of the rechargeable battery
When you have charged the appliance for the rst time, we advise you to
use it until the battery is completely empty. Continue to use the appliance
until the motor almost stops operating during a session.Then recharge the
battery. Follow this procedure at least twice a year.
Using the appliance
The hair length settings are indicated in millimeters.
The settings correspond to the remaining hair length after trimming.
Be careful when you trim for the rst time. Do not move the trimmer
too fast. Make smooth and gentle movements.
Tip: Start trimming at a high length setting and reduce the length setting
gradually until you have reached the desired hair length.
Trimming with comb
There are 3 different combs:
- 1-7mm
- 7-24mm
- 24-42mm
1 Attach one of the combs to the appliance.
2 Press up button or down button to select the desired length setting.
Note: When you trim for the rst time, start at the highest length setting to
familiarise yourself with the appliance.
3 Switch on the appliance.
ENGLISH6

4 To trim most effectively, move the trimmer against the hair growth
direction. Make sure that the surface of the comb always stays in
contact with the skin.
Trimming without comb
Use the trimmer without the trimming comb to trim hair close to the skin
(0.5mm) or to contour the neckline and sideburns.
Be careful when you trim without comb because the cutting
element removes every hair it touches.
1 Push the comb off the appliance.
2 Switch on the appliance.
3 Touch the hair lightly with the trimmer.
Make well-controlled movements.
Features
Length setting lock
This feature prevents accidental changing of the length setting during
trimming. Every time you switch on the appliance, the length setting lock
is activated.You can only change the length setting if you switch off the
appliance.
1 Press the up button or down button to select the length setting.
ENGLISH 7

2 Switch on the appliance.
,The lock symbol starts to ash. You cannot change the length
setting anymore.
Note: If you want to select a different length setting, switch off the appliance.
Press the up button or down button to select the desired length setting and
switch on the appliance again.
Cleaning
Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as alcohol, petrol or acetone to clean the appliance.
Never immerse the appliance in water or rinse it under the tap.
Note: Only the cutting element and the comb can be cleaned with water.
1 Make sure the appliance is switched off and disconnected from
the mains.
2 Wipe the housing of the appliance with a dry cloth.
3 Remove the comb and clean it with the brush or rinse it under
the tap.
Caution: Make sure that the comb is dry before you reattach it to
the appliance.
4 P
ress the release button (1).The cutting unit comes off the appliance (2).
5 Clean the cutting unit with the brush or rinse it under the tap.
Shake off excess water and leave to dry.
Do not dry the cutting unit with a towel, as this may damage the cutting
element.
Caution: Make sure that the cutting unit is dry before you reattach it to
the appliance.
6 Clean the inside of the appliance with the cleaning brush.
Never immerse the appliance in water or rinse it under the tap.
1
2
ENGLISH8

7 Insert the lug of the cutting unit into the guiding slot (1) and push
the cutting unit back onto the appliance (2).
Note: If the message ‘CL’ is shown on the display, too much hair has collected
between the comb and the cutting unit. Remove the comb and cutting unit and
clean them with the cleaning brush supplied. Also clean the top edge of the
handle with the cleaning brush supplied.
Replacement
Only replace a worn or damaged cutting unit with an original Philips cutting
unit, available from authorised Philips service centre.
1
Press the release button (1).The cutting unit comes off the appliance (2).
2 Insert the lug of the new cutting unit into the guiding slot (1)
and push the cutting unit onto the appliance (2).
Ordering accessories
To buy accessories or spare parts, visit www.shop.philips.com/service
or go to your Philips dealer.You can also contact the Philips Consumer
Care Centre in your country (see the worldwide guarantee leaet for
contact details).
Recycling
Do not throw away the appliance with the normal household waste at
the end of its life, but hand it in at an ofcial collection point for recycling.
By doing this, you help to preserve the environment.
Removing the rechargeable battery
Note: We strongly advise you to have a professional remove the
rechargeable battery.
Only remove the rechargeable battery if it is completely empty.
1 Disconnect the appliance from the mains and let the appliance
operate until the motor stops.
1
2
1
2
1
2
ENGLISH 9

2 Press the release button (1) and remove the cutting unit (2).
3 Insert the screwdriver between the motor unit and the back panel
of the appliance. Press down the screwdriver as far as it will go
4 Tilt the handle of the screwdriver downwards (1) and separate
the back panel from the appliance (2).
5 Remove the side panels. Pull the bottom part of the printed circuit
board with the rechargeable battery attached from the appliance.
6 Cut the wires to separate the rechargeable battery from the
appliance.
Do not connect the appliance to the mains again after you have opened it.
Guarantee and support
If you need information or support, please visit www.philips.com/
support or read the separate worldwide guarantee leaet.
1
2
2
1
ENGLISH10

11
Pendahuluan
Selamat atas pembelian Anda dan selamat datang di Philips!
Untuk memanfaatkan sepenuhnya dukungan yang ditawarkan Philips,
daftarkan produk Anda di www.philips.com/welcome.
Gambaran umum (Gbr. 1)
1 Unit pemotong
2 Tombol naik
3 Tombol turun
4 Tombol on/off
5 Kunci setelan panjang
6 Lampu pengisian daya
7 Layar
8 Sisir pemangkas 1-7 mm
9 Sisir pemangkas 7-24 mm
10 Sisir pemangkas 24-42 mm
11 Adaptor
12 Steker kecil
13 Sikat pembersih
Penting
Bacalah petunjuk pengguna ini secara saksama sebelum Anda menggunakan
alat dan simpan untuk referensi di kemudian hari.
Bahaya
- Jagalah agar alat dan adaptor selalu kering.
Peringatan
- Adaptor berisi trafo. Jangan memotong adaptor dan menggantinya
dengan steker lain, karena dapat membahayakan.
- Alat ini tidak dimaksudkan untuk digunakan oleh orang (termasuk anak-
anak) dengan cacat sik, indera atau kecakapan mental yang kurang,
atau kurang pengalaman dan pengetahuan, kecuali jika mereka diberikan
pengawasan atau petunjuk mengenai penggunaan alat oleh orang yang
bertanggung jawab bagi keselamatan mereka.
- Anak kecil harus diawasi untuk memastikan mereka tidak bermain-main
dengan alat ini.
Perhatian
- Alat ini tidak dapat dicuci. Jangan sekali-kali merendam alat di dalam air
atau membilasnya di bawah keran.
- Selalu periksa alat terlebih dulu sebelum menggunakannya.
Jangan gunakan alat, adaptor, atau komponen lain jika rusak karena
dapat menyebabkan cedera.
- Selalu ganti adaptor atau komponen yang rusak dengan yang asli.
- Hanya gunakan alat ini untuk keperluan yang dimaksud di petunjuk
pengguna.
- Jangan sekali-kali menggunakan udara bertekanan, sabut gosok,
bahan pembersih abrasif atau cairan agresif seperti bensin atau aseton
untuk membersihkan alat.
INDONESIA

Medan elektromagnet (EMF)
Alat Philips ini mematuhi semua standar dan peraturan yang berlaku
terkait paparan terhadap medan elektromagnet.
Umum
- Alat ini dilengkapi pemilih tegangan otomatis dan cocok untuk tegangan
listrik mulai 100 sampai 240 volt.
- Adaptor mengubah tegangan 100-240 volt menjadi tegangan rendah
yang aman di bawah 24 volt.
Pengisian daya
Isilah daya alat sampai penuh sebelum digunakan untuk pertama kali
atau jika sudah lama tidak digunakan.
Bila diisi daya selama 1 jam, alat memiliki waktu operasi tanpa kabel hingga
120 menit.
Catatan: Setelah mengisi daya alat sepenuhnya untuk pertama kalinya,
Anda juga bisa menggunakan alat langsung dari sumber listrik.
Cukup sambungkan alat ke sumber daya listrik.
Indikasi pengisian daya
Indikator baterai lemah
- Apabila baterai hampir kosong, lampu pengisian mulai berkedip jingga.
Pengisian daya
- Saat pengisian daya, lampu pengisian daya akan berkedip merah.
Baterai terisi penuh
- Saat baterai terisi penuh, lampu pengisian daya akan terus menyala
merah.
Catatan: Setelah 30 menit, lampu pengisian daya akan mati secara otomatis.
Mengisi baterai pencukur
1 Pastikan alat telah dimatikan.
2 Masukkan steker kecil ke dalam alat.
3 Masukkan adaptor ke stopkontak dinding.
4 Setelah pengisian daya selesai, cabut adaptor dari stopkontak dinding
dan lepaskan steker kecil dari alat.
INDONESIA12

Mengoptimalkan masa pakai baterai isi-ulang
Setelah mengisi daya alat untuk pertama kalinya, kami sarankan Anda untuk
menggunakannya hingga baterainya benar-benar kosong.
Lanjutkan penggunaan alat hingga motor hampir berhenti beroperasi dalam
sesi pemangkasan. Kemudian isi ulang baterai. Ikuti prosedur ini setidaknya
dua kali setahun.
Menggunakan alat
Setelan panjang rambut menggunakan ukuran milimeter.
Setelan ini menunjukkan panjang rambut yang tersisa setelah pemangkasan.
Hati-hati saat pertama kali memangkas. Jangan menggerakkan pemangkas
terlalu cepat. Lakukan gerakan yang halus dan perlahan.
Tip: Mulai pemangkasan di setelan panjang yang tinggi dan kurangi setelan
panjang sedikit demi sedikit hingga Anda mencapai panjang rambut yang
diinginkan.
Pemangkas dengan sisir
Terdapat 3 sisir yang berbeda:
- 1-7 mm
- 7-24 mm
- 24-42 mm
1 Pasang salah satu sisir ke alat.
2 Tekan tombol naik atau turun untuk memilih setelan panjang yang
diinginkan.
Catatan: Saat pertama kalinya memangkas, mulailah dengan setelan tertinggi
agar Anda terbiasa dengan alat ini.
3 Hidupkan alat.
INDONESIA 13

4 Untuk pemangkasan paling efektif, gerakkan pemangkas berlawanan
dengan arah tumbuh rambut. Pastikan bahwa permukaan sisir selalu
bersentuhan dengan kulit.
Memangkas tanpa sisir
Gunakan alat tanpa sisir pemangkas untuk memangkas rambut yang paling
dekat dengan kulit (0,5 mm) atau untuk membentuk lekukan garis leher
dan cambang.
Hati-hati saat memangkas tanpa sisir, karena elemen
pemangkas memotong setiap rambut yang tersentuh.
1 Lepaskan sisir dari alat.
2 Hidupkan alat tersebut.
3 Sentuh rambut perlahan menggunakan pemangkas.
Buat gerakan yang teratur dan terkendali.
Fitur
Kunci setelan panjang
Fitur ini mencegah perubahan setelan panjang yang tidak disengaja saat
memangkas. Setiap kali Anda menghidupkan alat, kunci setelan panjang akan
aktif. Anda hanya bisa mengubah setelan panjang apabila alat dimatikan.
1 Tekan tombol naik atau tombol turun untuk memilih setelan panjang.
INDONESIA14

2 Hidupkan alat tersebut.
,Simbol kunci mulai berkedip.Anda tidak lagi dapat mengubah setelan
panjang.
Catatan: Apabila Anda ingin memilih setelan panjang yang berbeda,
matikan alat. Tekan tombol naik atau tombol turun untuk memilih setelan
panjang yang diinginkan dan hidupkan alat kembali.
Membersihkan
Jangan sekali-kali menggunakan sabut gosok, bahan pembersih abrasif atau
cairan agresif seperti alkohol, bensin atau aseton untuk membersihkan alat.
Jangan merendam alat dalam air atau membilasnya di bawah keran.
Catatan: Hanya komponen pemangkas dan sisir yang boleh dibersihkan
dengan air.
1 Pastikan alat sudah dimatikan dan dicabut dari listrik.
2 Seka rangka luar alat dengan kain kering.
3 Lepaskan sisir dan bersihkan sisir dengan sikat atau bilas di
bawah keran.
Perhatian: Pastikan sisir kering sebelum Anda memasangkannya kembali
pada alat.
4 Tekan tombol pelepas (1). Unit pemotong lepas dari alat (2).
5 Bersihkan unit pemotong dengan sikat atau bilas unit di bawah air
keran. Kibaskan air yang tersisa dan biarkan hingga kering.
Jangan keringkan unit pemotong dengan handuk karena dapat merusak
elemen pemotong.
Perhatian: Pastikan unit pemotong kering sebelum Anda memasangkannya
kembali pada alat.
1
2
INDONESIA 15

6 Bersihkan bagian dalam alat dengan sikat pembersih.
Jangan merendam alat dalam air atau membilasnya di bawah keran.
7 Masukkan cuping unit pemotong ke dalam selot pemandu (1)
dan dorong unit pemotong kembali ke dalam alat (2).
Catatan: Apabila pesan ‘CL’ muncul di layar, berarti rambut yang menumpuk
di antara sisir dan unit pemotong sudah terlalu banyak. Lepaskan sisir dan
unit pemotong, lalu bersihkan keduanya menggunakan sikat pembersih yang
disertakan. Bersihkan juga tepi atas gagang dengan sikat pembersih yang
disertakan.
Penggantian
Ganti unit pemotong yang sudah aus atau rusak hanya dengan unit
pemotong Philips asli, tersedia di pusat servis resmi Philips.
1 Tekan tombol pelepas (1). Unit pemotong lepas dari alat (2).
2 Masukkan cuping unit pemotong baru ke dalam selot pemandu (1)
dan dorong unit pemotong kembali ke dalam alat (2).
1
2
1
2
1
2
INDONESIA16

Memesan aksesori
Untuk membeli aksesori atau suku cadang, kunjungi
www.shop.philips.com/service atau pergi ke dealer Philips Anda.
Anda juga dapat menghubungi Pusat Layanan Konsumen Philips di negara
Anda (lihat pamet garansi internasional untuk rincian kontak).
Mendaur ulang
Jangan membuang alat bersama limbah rumah tangga biasa jika alat sudah
tidak bisa dipakai lagi, tetapi serahkan ke tempat pengumpulan barang bekas
yang resmi untuk didaur ulang. Dengan melakukan ini, berarti Anda ikut
membantu melestarikan lingkungan.
Melepas baterai isi ulang
Catatan: Kami sangat menyarankan agar baterai isi ulang hanya dilepaskan
oleh seorang ahli.
Hanya keluarkan baterai yang dapat diisi ulang ini jika sudah
benar-benar kosong.
1 Lepaskan alat dari sumber listrik dan biarkan alat berjalan sampai
motornya berhenti sendiri.
2 Tekan tombol pelepas (1) lalu keluarkan unit pemotong (2).
3 Masukkan obeng di antara unit motor dan panel belakang alat.
Tekan obeng sedalam mungkin
4 Miringkan gagang obeng ke bawah (1) dan pisahkan panel belakang
dari alat (2).
5 Lepaskan panel samping.Tarik bagian bawah papan sirkuit bercetak
dengan baterai isi ulang yang terpasang dari alat.
1
2
2
1
INDONESIA 17

6 Potong kabel untuk memisahkan baterai isi-ulang dari alat.
Jangan lagi menghubungkan alat ke listrik setelah Anda membukanya.
Garansi dan dukungan
Jika Anda membutuhkan informasi atau dukungan, harap kunjungi
www.philips.com/support atau bacalah pamet garansi internasional.
INDONESIA18

19
소개
필립스 제품을 구입해 주셔서 감사합니다! 필립스가 드리는 지원
혜택을 받으실 수 있도록 www.philips.co.kr에서 제품을 등록하십
시오.
제품정보 (그림 1)
1 커팅 유닛
2 업 버튼
3 다운 버튼
4 전원 버튼
5 수염 길이 설정 잠금
6 충전 표시등
7 디스플레이
8 트리밍 빗(1-7mm)
9 트리밍 빗(7-24mm)
10 트리밍 빗(24-42mm)
11 어댑터
12 전원 플러그
13 청소용 브러시
중요 사항
본 제품을 사용하기 전에 이 사용 설명서를 주의 깊게 읽고 나중에
참조할 수 있도록 잘 보관하십시오.
주의
-제품과 어댑터에 물이 묻지 않도록 주의하십시오.
경고
-어댑터에는 변압기가 내장되어 있습니다. 위험할 수 있으므로
어댑터를 제거하고 다른 플러그로 교체하지 마십시오.
-신체적인 감각 및 인지능력이 떨어지거나 경험과 지식이 풍부
하지 않은 성인 및 어린이는 혼자 제품을 사용하지 말고 제품
사용과 관련하여 안전에 책임질 수 있도록 지시사항을 충분히
숙지한 사람의 도움을 받으십시오.
-어린이가 제품을 가지고 놀지 못하도록 지도해 주십시오.
주의
-이 제품은 물세척할 수 없습니다. 제품을 절대로 물에 담그거나
헹구지 마십시오.
-사용하기 전에 제품을 항상 확인하십시오. 제품, 어댑터 또는
기타 다른 부품이 손상되었을 경우 부상을 초래할 수 있으므로
사용하지 마십시오.
-손상된 어댑터 또는 부품은 반드시 정품으로 교체하여 사용하
십시오.
-사용 설명서에 나온 본래 용도로만 제품을 사용하십시오.
-제품을 세척할 때 압축 공기, 수세미, 연마성 세제나 휘발유,
아세톤과 같은 강력 세제를 사용하지 마십시오.
EMF(전자기장)
이 제품은 EMF(전자기장)와 관련된 모든 기준 및 규정을 준수합
니다.
한국어

일반
-제품에는 자동 전압 선택 기능이 있으며 100 ~ 240V 범위의
전원에서 사용할 수 있습니다.
-어댑터는 100-240V의 전압을 24V 이하의 안전한 저전압으로
변환해 줍니다.
충전
제품을 처음 사용하는 경우 또는 오랫동안 사용하지 않았을 경우,
제품을 완전히 충전하십시오.
1시간 충전하면 최대 120분 동안 무선으로 사용할 수 있습니다.
참고: 제품을 처음 사용할 때 완전히 충전한 후에는 제품을 직접
전원 코드에 연결해서도 사용할 수 있습니다. 제품을 전원 코드에
연결하기만 하면 됩니다.
충전 표시
배터리 전력 부족 표시등
-배터리가 거의 방전되면 충전 표시등이 주황색으로
깜빡입니다.
충전
-제품이 충전 중이면 충전 표시등이 빨간색으로 깜박입니다.
배터리 완전 충전
-배터리가 완전히 충전되면 충전 표시등에 빨간색 불이 켜진
상태로 유지됩니다.
참고: 30분 후 충전 표시등이 자동으로 꺼집니다.
제품 충전
1 제품의 전원이 꺼져 있는지 확인합니다.
2 소형 플러그를 제품에 제대로 꽂으십시오.
3 어댑터를 벽면 콘센트에 꽂으십시오.
4 충전 후에는 벽면 소켓에서 어댑터를 뽑고, 소형 플러그를 제품
에서 분리하십시오.
한국어20