Philips PT920CC User manual

Register your product and get support at
www.philips.com/welcome
PT920CC, PT925, PT920, PT870
Enregistrez votre produit et bénéciez d’une assistance à l’adresse suivante
www.philips.com/welcome

1

PT920CC, PT925, PT920, PT870
ENGLISH 6
FRANÇAIS (CANADA) 29

6
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips
offers, register your product at
www.philips.com/welcome.
Please read this user manual, as it contains
information about the wonderful features of this
shaver as well as some tips to make shaving easier
and more enjoyable.
General description (Fig. 1)
A Shaver (PT920CC/PT925/PT920/PT870)
1 Protection cap
2 Shaving unit
3 Shaving unit release button
4 Trimmer
5 Trimmer release slide
6 Shaver on/off button
7 Battery symbol and plug symbol
B Charging stand (PT925/PT920 only)
C Adapter
D Jet Clean System (PT920CC only)
1 Locking lever
2 Shaver holder
3 Cleaning chamber release button
4 Jet Clean System on/off button
5 Cleaning symbol, drying symbol and ‘uid low’
symbol
6 Battery symbol
E Jet Clean Solution
F Cleaning brush
G Storage pouch (PT920CC/PT925/PT920 only)
Note: You can nd the type number on the back of
the shaver.
ENGLISH

Important
Read this user manual carefully before you use the
shaver, the Jet Clean System (specic types only) and
the charging stand (specic types only). Save the user
manual for future reference.
Danger
- Make sure the adapter does not get wet.
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
- The shaver and the Jet Clean System are not
intended for use by persons (including children)
with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of these appliances by
a person responsible for their safety.
- Children should be supervised to ensure that
they do not play with the shaver and the
Jet Clean System.
- Always unplug the shaver before you clean it
under the tap.
Caution
- Never immerse the shaver in water.
- Never immerse the Jet Clean System or the
charging stand in water nor rinse it under the tap.
- Do not use the shaver in the bath or in the shower.
- Never use water hotter than 80°C to rinse the
shaver.
- Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
ENGLISH 7

- The shaver, the Jet Clean System, the charging stand
and the other accessories are not dishwasher-proof.
- Water may leak from the socket at the bottom
of the shaver when you rinse it.This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.
- Do not use the shaver, Jet Clean System, adapter,
charging stand or any other part if it is damaged,
as this may cause injury. Always replace a damaged
adapter, charging stand or part with one of the
original type.
- Use, charge (specic types only) and store the
shaver and the Jet Clean System at a temperature
between 10°C and 35°C.
- Always place and use the shaver and the Jet Clean
System on a surface that is uid-resistant.
- Only use the adapter, charging stand
and accessories supplied.
- Always put the protection cap on the shaver
to protect the shaving heads when you are travelling.
- Only use the Jet Clean System with the original
HQ200 cleaning uid.
- Always place the Jet Clean System on a stable,
level and horizontal surface to prevent leakage.
- When the Jet Clean System is ready for use, do
not move it to prevent leakage of cleaning uid.
- The Jet Clean System thoroughly cleans but does
not disinfect your shaver, therefore do not share
the shaver with others.
- Empty the cleaning chamber of the Jet Clean
System and clean the cleaning chamber thoroughly
by rinsing it with hot tap water every 15 days.
- If the shaver and the Jet Clean System
are subjected to a major change in temperature,
pressure or humidity, let them acclimatise for 30
minutes before you use them.
ENGLISH8

Compliance with standards
- The shaver complies with the internationally
approved IEC safety regulations and can be safely
cleaned under the tap.
- The shaver and the Jet Clean System comply with
all standards regarding electromagnetic elds
(EMF). If handled properly and according to the
instructions in this user manual, they are safe to
use based on scientic evidence available today.
General
- The appliance is equipped with an automatic
voltage selector and is suitable for mains voltages
ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
Charging
It takes approx. 1 hour to fully charge the shaver.
When you charge the shaver for the rst time or
after a long period of disuse, let it charge until the
white battery lights up continuously.
A fully charged shaver provides up to 21 (PT920CC/
PT925/PT920) or 17 (PT870) cordless shaves.
The shaving time may be less than 21 (PT920CC/
PT925/PT920) or 17 (PT870) cordless shaves as
a result of your shaving behaviour, your cleaning
habits or your beard type.
ENGLISH 9

Charge indications
Battery low
- When the battery is almost empty (when there
are only 5 or fewer shaving minutes left), the
orange plug symbol starts to ash.
- When you switch off the shaver, the orange plug
symbol continues to ash for a few seconds.
Quick charging
- When you start charging the empty battery, both
the white battery symbol and the plug symbol
ash. After approx. 3 minutes, the plug symbol
goes out, while the battery symbol continues to
ash. The shaver now contains enough energy for
a 5-minute shave.
Charging
- When the shaver is charging, the white battery
symbol ashes.
Battery fully charged
- When the battery is fully charged, the white
battery symbol lights up continuously.
Note: After approx. 30 minutes, the battery symbol
goes out to save energy.
ENGLISH10

Charging with the adapter
Do not charge the shaver in a closed pouch
(specic types only).
1 Put the small plug in the shaver.
2 Put the adapter in the wall socket.
,The battery symbol and the plug symbol show
the charging status of the shaver (see section
‘Charge indications’ in this chapter).
Charging in the charging stand (specic
types only)
1 Put the small plug in the charging stand.
2 Put the adapter in the wall socket.
3 Place the shaver in the charging stand.
,The battery symbol and the plug symbol show
the charging status of the shaver (see section
‘Charge indications’ in this chapter).
Charging in the Jet Clean System (specic
types only)
1 Put the small plug in the Jet Clean System.
2 Put the adapter in the wall socket.
3 Place the shaver without protection cap upside
down in the holder.
Note: The shaver cannot be placed in the Jet Clean
System when the protection cap is on the shaving unit.
4 Push down the locking lever completely to lock
the shaver into place.
ENGLISH 11

,The battery symbol on the Jet Clean System
ashes to indicate that the shaver is being
charged.
Note: When the Jet Clean System is performing the
cleaning program, the battery symbol is out.
,When the battery is fully charged, the battery
symbol on the Jet Clean System lights up
continuously.
Note: After approx. 30 minutes, the battery symbol
goes out to save energy.
5 To remove the shaver from the Jet Clean
System, move the locking lever upwards until
it does not go any further (1) and remove the
shaver (2).
ENGLISH12

Using the shaver
Note: You can also use the appliance directly from the
mains. Simply connect the shaver to the mains.
Shaving
1 Press the on/off button once to switch on the
shaver.
2 Move the shaving heads over your skin. Make
circular movements.
- Do not make straight movements.
- Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
3 Press the on/off button once to switch off the
shaver.
4 Clean the shaver (see chapter ‘Cleaning and
maintenance’).
Trimming
You can use the trimmer to groom your sideburns
and moustache.
1 Press the on/off button once to switch on the
shaver.
2 Push the trimmer slide downwards to open
the trimmer.
,You can now start trimming.
3 After trimming, close the trimmer and switch
off the shaver.
ENGLISH 13

Cleaning and maintenance
Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as petrol
or acetone to clean the shaver, the charging stand
(specic types only) and the Jet Clean System
(specic types only).
- The best and most hygienic way to clean the
shaver is in the Jet Clean System (specic types
only).You can also rinse the shaver under the tap
or clean it with the cleaning brush supplied.
- Clean the shaver after every shave for optimal
shaving performance.
- Regular cleaning guarantees better shaving
performance.
- For the best cleaning results, we advise you to use
the Philips Cleaning spray (HQ110) and (specic
types only) the Jet Clean solution (HQ200).
- Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
Note: Water may leak from the socket at the bottom
of the shaver when you rinse it. This is normal and not
dangerous because all electronics are enclosed in a
sealed power unit inside the shaver.
ENGLISH14

Cleaning the shaving unit under the tap
1 Switch off the shaver and disconnect it from
the mains.
2 Press the release button to open the shaving
unit.
3 Rinse the shaving unit and hair chamber under
a hot tap for 30 seconds.
Be careful with hot water.Always check if the
water is not too hot, to prevent your hands from
getting burnt.
- Rinse the hair chamber and the inside of the
shaving unit.
- Rinse the outside of the shaving unit.
4 Close the shaving unit and shake off excess
water.
Be careful not to hit the shaving unit against
anything while shaking off excess water.
Never dry the shaving unit and the hair chamber
with a towel or tissue, as this may damage the
shaving heads and the coupling spindles.
5 Open the shaving unit again and leave it open
to let the shaver dry completely.
ENGLISH 15

Cleaning the shaving unit with the cleaning
brush
1 Switch off the shaver and disconnect it from
the mains.
2 Press the release button to open the shaving
unit.
3 Pull the shaving unit off the shaver.
4 Turn the lock anticlockwise (1) and remove the
retaining frame (2).
5 Remove and clean one shaving head at a time.
Each shaving head consists of a cutter and a
guard.
Note: Do not clean more than one cutter and guard
at a time, since they are all matching sets. If you
accidentally mix up the cutters and guards, it may take
several weeks before optimal shaving performance is
restored.
- Remove the cutter from the shaving guard and
clean it with the brush.
ENGLISH16

- Clean the inside and outside of the shaving guard
with the brush.
6 Put the shaving heads back into the shaving
unit.
Make sure that the projections of the shaving
heads t exactly into the recesses.
7 Put the retaining frame back into the shaving
unit and turn the lock clockwise.
8 Insert the lug of the shaving unit into the slot
in the top of the shaver (1). Then close the
shaving unit (2).
Note: If the shaving unit does not close smoothly, check
if you have inserted the shaving heads properly and if
the retaining frame is locked.
Cleaning the shaving unit in the Jet Clean
System (specic types only)
The Jet Clean System cleans the shaving unit.
Preparing the Jet Clean System for use
Note: Fill the cleaning chamber before rst use and
when the ‘uid low’ symbol ashes to indicate that the
uid level is too low. When the uid level drops below
the minimum level, the cleaning symbol and the ‘uid
low’ symbol start to ash and the holder returns to its
starting position
ENGLISH 17

1 Simultaneously press the release buttons on both
sides of the cleaning chamber (1). Then lift the
Jet Clean System off the cleaning chamber (2).
,The cleaning chamber remains behind.
2 Unscrew the cap from the bottle with HQ200
cleaning uid and remove the airtight seal.
3 Fill the cleaning chamber with HQ200 cleaning
uid up to the MAX indication.
Note: Make sure the cleaning chamber is always lled
above the MIN indication.
4 Place the Jet Clean System back onto the
cleaning chamber (‘click’).
Make sure that the release buttons snap back into
place.
When the cleaning chamber is lled with
cleaning uid, do not move it to prevent leakage of
cleaning uid.
5 Put the small plug in the Jet Clean System and
put the adapter in the wall socket.
,The holder automatically moves to the highest
position.
The Jet Clean System is now ready for use.
Using the Jet Clean System
1 Place the shaver without protection cap upside
down in the holder. Push down the locking
lever completely to lock the shaver into place.
,The battery symbol on the Jet Clean System goes
on to indicate that the shaver is being charged.
Note: The shaver cannot be placed in the Jet Clean
System when the protection cap is on the shaving unit.
ENGLISH18

2 Press the on/off button on the Jet Clean
System to start the cleaning program.
The cleaning program has two phases, the cleaning
phase and the drying phase.
,The battery symbol on the Jet Clean System
goes out.
,During the rst phase of the cleaning program,
the cleaning symbol starts to ash and the
shaver is automatically lowered into the cleaning
uid.
,The shaver automatically switches on and off
several times and moves up and down.
,The cleaning symbol ashes throughout the
cleaning program, which takes approx. 8 minutes.
,During the second phase of the cleaning
program, the shaver is placed in the drying
position, indicated by a ashing drying symbol.
This phase takes approx. 4 hours.The shaver
stays in this position until the end of the program.
,After the cleaning program, the battery symbol
on the Jet Clean System goes on to indicate that
the shaver is being charged.
Note: If you press the on/off button of the Jet Clean
System during the cleaning program, the program aborts
and resets. In this case, the cleaning or drying symbol
stops ashing and the holder returns to its starting
position. The shaver may still be wet and dirty, because
the cleaning program has not been nished.
Note: If you remove the adapter from the wall socket
during the cleaning program, the program aborts. The
holder remains in its current position. When you put
the adapter back into the wall socket, the holder moves
to the highest position.
ENGLISH 19

Note: When the uid level drops below the minimum
level, the cleaning symbol and the ‘uid low’ symbol
start to ash with intervals and the holder returns to its
starting position
Cleaning the Jet Clean System
Empty the cleaning chamber and clean it thoroughly
by rinsing it with hot tap water every 15 days if you
use the Jet Clean System daily. Otherwise empty and
clean the cleaning chamber at least once a month.
1 Clean the outside of the Jet Clean System with
a moist cloth.
Never immerse the Jet Clean System in water, nor
rinse it under the tap.
2 Simultaneously press the release buttons on
both sides of the Jet Clean System (1). Then lift
the Jet Clean System off the cleaning chamber
(2).
,The cleaning chamber remains behind.
3 Pour any remaining cleaning uid out of the
cleaning chamber.
You can simply pour the cleaning uid down the sink,
this is not harmful to the environment.
4 Rinse the cleaning chamber under a hot tap.
Be careful with hot water.Always check if the
water is not too hot, to prevent your hands from
getting burnt.
The cleaning chamber is not dishwasher-proof.
ENGLISH20