Philips HQ7310 User manual

HQ7350, HQ7340, HQ7320, HQ7310
ENGLISH 4
DANSK 15
DEUTSCH 26
 37
SUOMI 49
NORSK 60
SVENSKA 71
91
101

4
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benet from the support that
Philips offers, register your product at www.philips.
com/welcome.
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Only use the powerplug supplied.
The powerplug transforms 100-240 volts to a safe
low voltage of less than 24 volts.
The powerplug contains a transformer. Do not cut
off the powerplug to replace it with another plug,
as this causes a hazardous situation.
Do not use a damaged powerplug.
If the powerplug is damaged, always have it
replaced with one of the original type in order to
avoid a hazard.
Make sure the powerplug does not get wet.
Charge and store the shaver at a temperature
between 5°C and 35°C.
Always unplug the shaver before cleaning it under
the tap.
-
-
-
-
-
-
-
-
-
-
ENGLISH

The appliance complies with the internationally
approved IEC safety regulations and can be safely
cleaned under the tap.
Be careful with hot water. Always check if the water
is not too hot, to prevent your hands from getting
burnt.
This washable shaver is not suitable for shaving in
the shower.
Do not immerse the shaver in water.
Water may leak from the socket at the bottom
of the appliance when you rinse it.This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.

This Philips appliance complies with all standards
regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this
user manual, the appliance is safe to use based on
scientic evidence available today.
Charging
Make sure the appliance is switched off before you
start to charge it.
Charging takes at least 8 hours.
You can also shave without charging by connecting
the shaver to the mains.
-
-
-
-
ENGLISH 5


Charging
When you start charging the empty shaver, the
charging light goes on.
Battery fully charged
When the battery is fully charged, the charging
light starts to ash.
When you unplug the shaver, the charging light goes
out.

After charging, the shaver has a cordless shaving time
of up to 35 minutes.
Charging the appliance
Charge the appliance when the motor stops or
starts running slower.
1 Put the appliance plug in the shaver.
2 Put the powerplug in the wall socket.
3 Remove the powerplug from the wall socket
and pull the appliance plug out of the shaver
when the battery has been fully charged.


1 Press the on/off button once to switch on the
shaver.
The power-on lights go on to indicate that the
motor is running.
,
,
ENGLISH6

2 Move the shaving heads quickly over your skin,
making both straight and circular movements.
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
3 Press the on/off button once to switch off the
shaver.
The power-on lights go out.
4 Clean the shaver (see chapter ‘Cleaning and
maintenance’).
5 Put the protection cap on the shaver every
time you have used it, to prevent damage to
the shaving heads.
Trimming
For grooming sideburns and moustache.
1 Open the trimmer by pushing the slide
downwards.
The trimmer can be activated while the motor is
running.
2 Close the trimmer (‘click’).
Cleaning and maintenance
Regular cleaning guarantees better shaving
performance.
-
-
ENGLISH 7

Be careful with hot water.Always check if the
water is not too hot, to prevent your hands from
getting burnt.
Note:Water may leak from the socket at the bottom of
the appliance when you rinse it.This is normal and not
dangerous.

1 Switch off the shaver, remove the powerplug
from the wall socket and pull the appliance plug
out of the shaver.
2 Press the release button to open the shaving
unit.
3 Clean the shaving unit and the hair chamber by
rinsing them under a hot tap for some time.
Make sure you clean the inside as well as the
outside of the shaving unit.
4 Close the shaving unit and shake off excess
water.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
5 Open the shaving unit again and leave it open
to let the appliance dry completely.
You can also clean the hair chamber without water
by using the brush supplied.
,
ENGLISH8


1 Open the shaving unit, turn the lock
anticlockwise (1) and remove the retaining
frame (2).
2 Clean the cutters and guards with the brush
supplied.
Do not clean more than one cutter and guard
at a time, since they are all matching sets. If you
accidentally mix up the cutters and guards, it
may take several weeks before optimal shaving
performance is restored.
3 Put the shaving heads back into the shaving
unit. Put the retaining frame back into the
shaving unit and turn the lock clockwise.
4 Close the shaving unit.
Trimmer
Clean the trimmer every time you have used it.
1 Switch off the shaver, remove the powerplug
from the wall socket and pull the appliance plug
out of the shaver.
2 Clean the trimmer with the brush supplied.
3 Lubricate the trimmer teeth with a drop of
sewing machine oil every six months.
ENGLISH 9

Storage
Put the protection cap on the shaver to prevent
damage to the shaving heads.
Replacement
Replace the shaving heads every two years for
optimal shaving results.
Replace damaged or worn shaving heads with HQ8
Philips shaving heads only.
Note: Do not mix up the cutters and the guards to
guarantee optimal shaving performance.
1 Switch off the shaver, remove the powerplug
from the wall socket and pull the appliance plug
out of the shaver.
2 Press the release button to open the shaving
unit.
3 Turn the lock anticlockwise (1) and remove the
retaining frame (2).
4 Remove the shaving heads and place new ones
in the shaving unit. Put the retaining frame
back into the shaving unit and turn the lock
clockwise.
Make sure that the projections of the shaving
heads t exactly into the recesses.
5 Close the shaving unit.
,
,
ENGLISH10


The following accessories are available:
HQ8500/HQ8000 powerplug.
HQ8 Philips Shaving Heads.
HQ110 Philips Shaving Head Cleaning Spray.
HQ8010 car cord.
Note: Some accessories may not be available in all
countries. Contact the Consumer Care Centre in your
country about the availability of this accessory.

Do not throw away the appliance with the normal
household waste at the end of its life, but hand
it in at an ofcial collection point for recycling. By
doing this, you help to preserve the environment.

The built-in rechargeable lithium-ion (Li-ion)
battery contains substances that may pollute the
environment.Always remove the battery before
you discard and hand in the appliance at an ofcial
collection point. Dispose of the battery at an ofcial
collection point for batteries. If you have trouble
removing the battery, you can also take the appliance
to a Philips service centre.The staff of this centre will
remove the battery for you and will dispose of it in
an environmentally safe way.
Only remove the battery if it is completely empty.
1 Remove the powerplug from the wall socket
and pull the appliance plug out of the shaver.
-
-
-
-
-
ENGLISH 11

2 Let the shaver run until it stops, undo the two
screws in the hair chamber and remove it.
3 Undo the two screws at the back of the shaver
and remove the back panel of the housing.
4 Remove the side panels by pulling them off the
sealed power unit.
5 Undo the three screws in the sealed power
unit.
6 Remove the back panel of the sealed power
unit by means of a screwdriver.
7 Remove the battery.
Be careful, the battery strips are very sharp.
Do not connect the shaver to the mains again after
the battery has been removed.
ENGLISH12


If you need service or information or if you have a
problem, please visit the Philips website at
www.philips.com or contact the Philips Consumer
Care Centre in your country (you nd its phone
number in the worldwide guarantee leaet). If there
is no Consumer Care Centre in your country, go to
your local Philips dealer.

The shaving heads (cutters and guards) are not
covered by the terms of the international guarantee
because they are subject to wear.

1 Reduced shaving performance.
Cause 1: the shaving heads are dirty.The shaver has
not been rinsed long enough or the water used was
not hot enough.
Clean the shaver thoroughly before you continue
shaving. See chapter ‘Cleaning and maintenance’.
Cause 2: long hairs are obstructing the shaving heads.
Clean the cutters and guards with the brush
supplied. See chapter ‘Cleaning and maintenance’,
section ‘Every six months: shaving heads’.
Cause 3: the shaving heads are damaged or worn.
Replace the shaving heads. See chapter
‘Replacement’.
2 The shaver does not work when the on/off
button is pressed.
Cause 1: the battery is empty.
Recharge the battery. See chapter ‘Charging’.
Cause 2: the appliance is not connected to the
mains.
Put the powerplug in the wall socket.
,
,
,
,
,
ENGLISH 13

3 The shaving unit has come off the shaver.
The shaving unit has not been placed correctly.
If the shaving unit becomes detached from the
shaver, you can easily put it back by inserting
the hinge into the slot in the rim of the hair
chamber and pushing it home until it locks into
place (‘click’).
,
ENGLISH14

15
Introduktion
Tillykke med dit køb og velkommen til Philips! For at
få fuldt udbytte af den støtte, Philips tilbyder, skal du
registrere dit produkt på www.philips.com/welcome.
Vigtigt
Læs denne brugsvejledning omhyggeligt igennem,
inden apparatet tages i brug, og gem den til
eventuelt senere brug.
Dette apparat er ikke beregnet til at blive brugt af
personer (herunder børn) med nedsatte fysiske
og mentale evner, nedsat følesans eller manglende
erfaring og viden, medmindre de er blevet vejledt
eller instrueret i apparatets anvendelse af en
person, der er ansvarlig for deres sikkerhed.
Apparatet bør holdes uden for børns rækkevidde
for at sikre, at de ikke kan komme til at lege med
det.
Brug kun det medfølgende netstik.
Net/transformerstikket omformer 100-240 Volt til
en lav sikkerhedsspænding under 24 Volt.
Netstikket indeholder en transformer. Derfor må
det aldrig klippes af og udskiftes med et andet stik,
da det vil resultere i en farlig situation.
Brug aldrig et beskadiget netstik.
Hvis netstikket beskadiges, må det kun udskiftes
med et originalt netstik af samme type for at
undgå enhver risiko ved efterfølgende brug.
Sørg for, at netstikket ikke bliver vådt.
Shaveren skal oplades og opbevares ved en
temperatur mellem 5° C og 35° C.
Tag altid stikket ud af shaveren, inden den skylles
under vandhanen.
-
-
-
-
-
-
-
-
-
-
DANSK

Produktet opfylder de internationalt godkendte
IEC-sikkerhedsregler og kan skylles under rindende
vand uden risiko.
Vær forsigtig med varmt vand. Kontrollér altid, at
vandet ikke er for varmt, så du ikke skolder dine
hænder.
Denne vaskbare shaver er ikke beregnet til brug i
brusebadet.
Kom aldrig shaveren ned i vand.
Når shaveren rengøres, kan der dryppe lidt vand
ud af stikket i bunden. Dette er helt normalt og
ganske ufarligt, da al elektronikken er indkapslet i
en forseglet motorenhed inde i shaveren.

Dette Philips-apparat overholder alle standarder
for elektromagnetiske felter (EMF). Ved korrekt
anvendelse i overensstemmelse med instruktionerne
i denne brugsvejledning, er apparatet sikkert at
anvende, ifølge den videnskabelige viden, der er
tilgængelig i dag.
Opladning
Kontrollér, at apparatet er slukket, før opladningen
påbegyndes.
Opladning tager mindst 8 timer.
Shaveren kan også anvendes uden opladning, blot
den tilsluttet en stikkontakt.
-
-
-
-
DANSK16


Opladning
Når opladning af shaveren påbegyndes, lyser
opladeindikatoren.

Når batteriet er fuldt opladet, begynder
opladeindikatoren at blinke.
Opladeindikatoren slukker, når stikket tages ud af
stikkontakten.

Efter opladning har shaveren op til 35 minutters
ledningsfri brugstid.
Opladning
Genoplad apparatet, når motoren stopper eller
begynder at køre langsommere.
1 Sæt apparatstikket ind i shaveren.
2 Sæt netstikket i stikkontakten.
3 Så snart shaveren er ladet helt op, tages stikket
ud af stikkontakten og apparatstikket ud af
shaveren.


1 Tryk en gang på on/off-knappen for at tænde
for shaveren.
Kontrollampen tænder for at vise, at motoren kører.
,
,
DANSK 17

2 Bevæg skærene hurtigt hen over huden både i
lige strøg og i cirkelbevægelser.
Resultatet bliver bedst, hvis huden er tør.
Vær opmærksom på, at der kan gå 2-3 uger,
før din hud helt har vænnet sig til Philips’
barberingssystem.
3 Tryk en gang på on/off-knappen for at slukke
for shaveren.
Kontrollampen slukker.
4 Rengør shaveren (se afsnittet “Rengøring og
vedligeholdelse”).
5 Sæt altid beskyttelseskappen på shaveren efter
brug for at undgå at beskadige skærene.
Trimning
Til pleje af bakkenbarter og moustache.
1 Trimmeren åbnes ved at trykke skydekontakten
nedad.
Trimmeren kan aktiveres, mens shaveren kører.
2 Luk trimmeren med et klik.

Regelmæssig rengøring sikrer det bedste
barberingsresultat.
-
-
DANSK18

Vær forsigtig med varmt vand. Kontrollér altid, at
vandet ikke er for varmt, så du ikke skolder dine
hænder.
Bemærk: Der kan dryppe lidt vand ud gennem stikket
i bunden af shaveren, når du skyller den. Dette er helt
normalt og ganske ufarligt.

1 Sluk for shaveren, tag netstikket ud af
stikkontakten og apparatstikket ud af shaveren.
2 Tryk på udløserknappen og luk skærhovedet
op.
3 Skyl skærhoved og skægkammer grundigt
under den varme hane.
Sørg for, at rengøre både inder- og ydersiden af
skærhovedet.
4 Luk skærhovedet, og ryst overskydende vand
væk.
Skærhovedet må ikke tørres med et håndklæde
eller køkkenrulle, da dette kan beskadige skærene.
5 Luk skærhovedet op igen - og lad det være
åbent - til shaveren er helt tør.
Skægkammeret kan også renses uden brug af vand
ved hjælp af den medfølgende børste.
,
DANSK 19


1 Åbn skærhovedet, drej låsen venstre om (1) og
tag samlerammen af (2).
2 Rengør knive og lamelkapper med den
medfølgende børste.
Rens kun ét skær ad gangen, da knive og lamelkapper
er slebet parvis. Kommer man ved en fejltagelse til at
blande knive og lamelkapper, kan det tage ere uger,
før shaveren igen barberer optimalt.
3 Sæt skærene tilbage i skærhovedet. Sæt
samlerammen tilbage på plads og drej låsen
højre om.
4 Luk skærhovedet.
Trimmer
Rens trimmeren hver gang den har været brugt.
1 Sluk for shaveren, tag netstikket ud af
stikkontakten og apparatstikket ud af shaveren.
2 Rens trimmeren med den medfølgende børste.
3 Smør trimmerens tænder med en dråbe
symaskineolie hver 6. måned.
DANSK20


Sæt altid beskyttelseskappen på shaveren efter
brug for at undgå at beskadige skærene.

For til stadighed at opnå et optimalt
barberingsresultat anbefales det at udskifte
skærene hvert 2. år.
Beskadigede eller slidte skær må kun udskiftes med
HQ8 Philips skær.
Bemærk: For at bevare et optimalt barberingsresultat,
skal du passe på ikke at komme til at blande de
enkelte sæt af knive og lamelkapper.
1 Sluk for shaveren, tag netstikket ud af
stikkontakten og apparatstikket ud af shaveren.
2 Tryk på udløserknappen og luk skærhovedet
op.
3 Drej låsen venstre om (1) og tag samlerammen
af (2).
4 Tag skærene ud og sæt de nye i. Sæt
samlerammen tilbage i skærhovedet og drej
låsen højre om..
Sørg for, at de små tappe passer præcist ned i
recesserne.
5 Luk skærhovedet.
,
,
DANSK 21


Der ndes følgende tilbehør:
HQ8500/HQ8000 netstik
HQ8 Philips skær.
HQ110 Philips Shaving Head Cleaning Spray
(rengøringsspray til skær).
HQ8010 car cord (ledning til cigartænderstik).
Bemærk: Nogle tilbehørsdele føres muligvis ikke i
alle lande. Kontakt dit lokale Kundecenter for at få
nærmere oplysninger.

Apparatet må ikke smides ud sammen med
almindeligt husholdningsaffald, når det til sin tid
kasseres. Aevér det i stedet på en kommunal
genbrugsstation. På den måde er du med til at
beskytte miljøet.

Det indbyggede genopladelige lithiumion-batteri
indeholder stoffer, der kan forurene miljøet. Fjern
altid batteriet, før du til sin tid kasserer apparatet, og
aeverer det på en genbrugsstation. Aevér batteriet
på et ofcielt indsamlingssted for brugte batterier.
Kan du ikke få batteriet ud, kan du aevere apparatet
til Philips, som vil sørge for at tage batteriet ud og
bortskaffe det på en miljømæssig forsvarlig måde.
Tag kun batteriet ud, hvis det er helt aadet.
1 Tag netstikket ud af stikkontakten og
apparatstikket ud af shaveren.
-
-
-
-
-
DANSK22