Philips NORELCO S6540 User manual

Tripleheader shaver
S6540
Tripleheader shaver

1
2
4
5
6
8
10
7
9
3
15
11
13
12
14

empty page before TOC

English 6

English
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric product, basic precautions should
always be followed, including the following:
Read all instructions before using this product.
DANGER
To reduce the risk of electric shock:
-Do not reach for a corded product that has fallen into water.
Unplug immediately from the power outlet.
-Keep the power cord dry.
-Do not place or store the product where it can fall or be
pulled into a tub or sink. Do not place or drop the product
into water or other liquid.
-Except when charging, always unplug this product from the
power outlet immediately after use.
-Remove power cord from power outlet and product before
cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to
persons:
-Close supervision is required when this product is used by,
on, or near children, or persons with limited physical, sensory,
or mental capabilities or invalids.
-Use this product only for its intended household use as
described in this manual. Do not use attachments not
recommended by Philips North America LLC.
6English

-Never operate this product if it has a damaged power cord, if
it is not working properly, after it has been dropped or
damaged, or after the product or power cord has been
dropped into water. For assistance call 1-800-243-3050.
-Keep the power cord away from heated surfaces.
-Never drop or insert any object into any opening.
-Do not use the power cord in or near a power outlet that
contains an electric air freshener to prevent damage to the
power cord.
-Do not use product outdoors or operate where aerosol
(spray) products are being used or where oxygen is being
administered.
-Always check cutters, cutting unit and guards before using
the product. Do not use the product if cutters, cutting unit or
guards are damaged, as injury may occur.
-Always attach power cord to product first, then to power
outlet. To disconnect, set all controls to 'off' position. Then
remove power cord from power outlet.
-Plug power cord directly into power outlet. Do not use an
extension cord.
-Unplug power cord before plugging in or unplugging the
product.
-Only use the power cord and other accessories supplied with
the product.
-Do not attempt to open the product to remove or replace the
built-in rechargeable battery.
-The batteries used in this product may present a fire or
chemical burn hazard if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
IMPORTANT: The power plug contains a transformer. Do not
cut off the power plug to replace it with another plug as this will
cause a hazardous condition.
7
English

SAVE THESE
INSTRUCTIONS
Contents
IMPORTANT SAFETY INSTRUCTIONS______________________ 6
General description_________________________________________ 8
Introduction_________________________________________________ 9
The display__________________________________________________ 9
Charging_____________________________________________________ 12
Using the shaver_____________________________________________ 13
Using click-on attachments_________________________________ 17
Travel lock___________________________________________________ 18
Cleaning and maintenance_________________________________ 19
Replacement________________________________________________ 23
Storage______________________________________________________ 24
Accessories__________________________________________________ 24
Assistance___________________________________________________ 25
Disposal_____________________________________________________ 25
Full Two-Year Warranty_____________________________________ 25
45-DAY MONEY-BACK GUARANTEE_______________________ 27
General description
1 Click-on precision trimmer attachment
2 Shaving unit with hair chamber
3 Shaving head holder release button
4 On/off button
5 Turbo+ button
6 Cleaning reminder
7 Replacement reminder
8 Travel lock symbol
9 'Unplug for use' reminder
8English

10 Battery charge indicator
11 Socket for small plug
12 Power plug
13 Cleaning brush
14 Travel case
Introduction
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.philips.com/register.
The display
Battery charge indicator
Quick charge: When the battery is empty and
you connect the shaver to a power outlet, the
lights of the battery charge indicator light up
white one after the other repeatedly. When the
battery contains enough energy for one shave,
the bottom light of the battery charge
indicator flashes white slowly.
As charging continues, each light blinks and
then lights continuously indicating to what
level the battery has been charged.
Battery fully charged
Note: This shaver can only be used without
cord.
9
English

When the battery is fully charged, all lights of
the battery charge indicator light up white
continuously.
Note: When you press the on/off button
during or after charging, the 'unplug for use'
symbol lights up to indicate that the shaver is
still connected to the power outlet.
Note: When the battery is full, the display
switches off automatically after 30 minutes.
Battery low
When the battery is almost empty, the bottom
light of the battery charge indicator flashes
orange.
Remaining battery charge
The remaining battery capacity is indicated by
the lights of the battery charge indicator that
light up continuously.
’Unplug for use’ reminder
The ‘unplug for use’ reminder flashes to
remind you to disconnect the shaver from the
power outlet before you can switch it on.
10 English

Cleaning reminder
Clean the shaver after every use for optimal
performance (see 'Cleaning and maintenance').
When you switch off the shaver, the cleaning
reminder flashes to remind you to clean the
shaver. .
Travel lock
When you are going to travel, you can lock the
shaver to prevent it from accidentally
switching on.
Replacing shaving heads
For maximum shaving performance, replace
the shaving heads every year. The shaver is
equipped with a replacement reminder, which
flashes to indicate you have to replace the
shaving heads.
Note: After replacing the shaving heads, you
can reset the replacement reminder by
pressing the on/off button for 7 seconds. If you
do not reset the replacement reminder, the
shaver resets automatically after 9 shaves.
Turbo+ setting
This setting allows you to shave through dense
parts of the beard. The Turbo+ button lights
up continuously to indicate that the setting is
activated.
11
English

Charging
-Charging or using the product at
temperatures below 40°F (4.5°C) or higher
than 95°F (35°C) adversely affects the
lifespan of the battery.
-Do not charge the shaver in a pouch or
travel case.
-The power plug transforms 100-240V AC to
less than 24V DC.
Charge the shaver before you use it for the first
time and when the display indicates that the
battery is almost empty.
Charging takes approx. 1 hour. A fully charged
shaver has a shaving timeof up to 60 minutes.
Note: You cannot use the shaver while it is
charging.
Quick charge
After approx. 5 minutes of charging, the
battery contains enough energy for one shave.
The bottom light of the battery charge
indicator flashes white slowly when the quick
charge is finished.
Charging with the power cord
1Make sure that the shaver is switched off.
2Put the small plug in the shaver and
connect the power plug to any 100V to
240V AC outlet. Use only the power cord
provided.
The display of the shaver indicates that the
shaver is charging.
12 English

3After charging, remove the power plug from
the wall outlet and pull the small plug out of
the shaver.
Note: An adapter plug may be necessary for
cord usage in some foreign countries. Use an
attachment plug adapter of the proper
configuration for the power outlet.
Using the shaver
Always check the shaver and all accessories
before use. Do not use the shaver or any
accessory if it is damaged, as this may cause
injury. Always replace a damaged part with
one of the original type.
This symbol indicates that the shaver can be
used in the bath or shower.
-Use this shaver for its intended household
use as described in this manual.
-For hygienic reasons, the shaver should
only be used by one person.
Note: This shaver is waterproof. It is suitable
for use in the bath or shower and for cleaning
under the tap. For safety reasons, the shaver
can only be used without cord.
21-Day adaptation process
-21 Day Trial and Conversion Process. It is a
fact that your skin and beard need time to
adjust to a new grooming system.
13
English

-Use your new shaver exclusively for 3 weeks
to fully enjoy the closeness of a Philips
Norelco shave.
-At first you may not get as close a shave as
you expect, or your face may even become
slightly irritated. This is normal since your
beard and skin will need time to adjust.
Invest 3 weeks and you'll soon experience
the full joy of your new shaver.
-Stick with it! If you alternate shaving
methods during the adjustment period, it
may make it more difficult to adapt to the
Philips Norelco shaving system.
-If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
Switching the shaver on and off
1To switch the shaver on or off, press the
on/off button once.
The display lights up for a few seconds to
show the remaining battery charge.
Shaving
-For the best results on skin comfort, pre-
trim your beard if you have not shaved for 3
days or longer.
Dry shaving
1Switch on the shaver.
14 English

2Move the shaving heads over your skin in
circular movements to catch all hairs
growing in different directions. Make sure
each shaving head is fully in contact with
the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, as this can
cause skin irritation.
3Switch off and clean the shaver after each
use.
The display lights up for a few seconds to
show the battery charge.
Wet shaving
For a more refreshing shave, you can also use
this shaver on a wet face with shaving foam or
shaving gel.
1Apply some water to your skin.
2Apply shaving foam or shaving gel to your
skin.
15
English

3Rinse the shaving unit under the tap to
ensure that the shaving unit glides smoothly
over your skin.
4Switch on the shaver.
5Move the shaving heads over your skin in
circular movements to catch all hairs
growing in different directions. Make sure
each shaving head is fully in contact with
the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, this can cause
skin irritation.
Note: Rinse the shaving unit regularly to
ensure that it continues to glide smoothly
over your skin.
6Dry your face.
7Switch off the shaver and clean it after each
use.
Note: Make sure that you rinse all foam or
shaving gel off the shaver.
Turbo+ setting
1Switch on the shaver.
2Press the Turbo+ button once if you want
to shave areas with dense hair.
Note: The Turbo+ button lights up
continuously to indicate that the setting is
activated.
16 English

3Stretch your skin with your free hand so
blades can lift and cut hairs. Gently press
shaver to skin so the floating heads can
follow the contours of your face.
Do not press too hard as too much pressure
can cause shaving heads to pinch the skin.
4Switch off the Turbo+ setting by pressing
the Turbo+ button once.
Using click-on attachments
Removing or attaching the click-on attachment
1Make sure the shaver is switched off.
2Pull the attachment straight off the shaver.
Note: Do not twist the attachment while you
pull it off the shaver.
3Insert the lug of the attachment into the slot
in the top of the shaver. Then press down
the attachment to attach it to the shaver
(‘click’).
Using the precision trimmer attachment
You can use the precision trimmer to touch up
your beard, sideburns and moustache.
1Attach the trimmer to the shaver ('click').
2Switch on the shaver.
17
English

3Hold the trimmer perpendicular to the skin
and move it downwards while exerting
gentle pressure.
4Switch off and clean the trimmer after use.
Note: Trimming is easier when the skin and
hair are dry.
Travel lock
You can lock the shaver when you are going to
travel to prevent it from switching on
accidentally.
Activating the travel lock
3 sec.
1Press the on/off button for 3 seconds to
use the travel lock mode.
While you activate the travel lock, the
indicator on the display lights up briefly.
When the travel lock is activated, the travel
lock symbol flashes.
Deactivating the travel lock
1Press the on/off button for 3 seconds.
While you deactivate the travel lock, the
indicator on the display lights up briefly.
When the travel lock is deactivated, the
travel lock symbol flashes and goes out. The
shaver switches on and is now ready for use
again.
18 English

Note: The shaver unlocks automatically when
it is connected to a power outlet.
Cleaning and maintenance
Regular cleaning guarantees better
shaving results.
Never clean, remove or replace the shaving
unit while the shaver is switched on.
Do not touch shaving heads with hard
objects as this may dent or damage the
precision-made slotted combs.
Do not use abrasives, scourers or
aggressive liquids such as gasoline or
acetone to clean the shaver.
Cleaning the shaver under the tap
Clean the shaver after every use for optimal
performance (see 'Cleaning and maintenance').
Be careful with hot water. Always check if the
water is not too hot, to prevent burning your
hands.
Never dry the shaving unit with a towel or
tissue, as this may damage the shaving
heads.
While rinsing the shaving unit, water may drip
out of the base of the shaver. This is a normal
occurrence.
1Switch on the appliance.
19
English

2Rinse the shaving unit under a warm tap.
3Switch off the appliance. Press the release
button to open the shaving unit.
4Rinse the hair chamber under the tap.
5Rinse the shaving head holder under a
warm tap.
6Carefully shake off excess water and let the
shaving head holder air-dry completely.
7Close the shaving head holder ('click').
Thorough cleaning
We advise you to clean the shaving heads
thoroughly once a month or when the shaver
does not shave as well as it used to.
20 English