Philips Norelco S95 Series User manual

S95xx/S93xx

1

S95XX, S93XX
ENGLISH 4
БЪЛГАРСКИ 25
ČEŠTINA 47
EESTI 68
HRVATSKI 89
MAGYAR 110
ҚАЗАҚША 130
LIETUVIŠKAI 151
LATVIEŠU 172
POLSKI 192
ROMÂNĂ 212
РУССКИЙ 233
SLOVENSKY 255
SLOVENŠČINA 277
SRPSKI 298
УКРАЇНСЬКА 319

4
Introduction
Congratulations on your purchase and welcome to Philips!
To fully benet from the support that Philips offers, register your product
at www.philips.com/welcome.
Please read this user manual, as it contains information about the features
of this shaver as well as some tips to make shaving easier and more
enjoyable.
General description (Fig. 1)
1 Comb for beard styler attachment
2 Click-on beard styler attachment
3 Click-on trimmer attachment
4 Click-on shaving unit
5 On/off button
6 Socket for small plug
7 Exclamation mark
8 Replacement reminder
9 Battery charge indicator
10 Travel lock symbol
11 Cleaning reminder
12 Personal settings
13 + and - buttons for personal settings
14 Replacement symbol
15 SmartClean system
16 Cap of SmartClean system
17 On/off button
18 Cleaning symbol
19 Drying symbol
20 Ready symbol
21 Charge symbol
22 Cleaning cartridge for SmartClean system
23 Adapter
24 Small plug
25 Retaining ring holder
26 Pouch
Important
Read this user manual carefully before you use the shaver and
the SmartClean system. Save this user manual for future reference.
Danger
- Keep the adapter dry.
Warning
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- The shaver and the SmartClean system are not intended for use
by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of these
appliances by a person responsible for their safety.
ENGLISH

- Children should be supervised to ensure that they do not play with
the shaver and the SmartClean system.
- Always unplug the shaver before you clean it under the tap.
Caution
- Never immerse the SmartClean system in water nor rinse it under the
tap.
- Never use water hotter than 80°C to rinse the shaver.
- Do not use the shaver, SmartClean system, adapter or any other part
if it is damaged, as this may cause injury. Always replace a damaged
adapter or part with one of the original type.
- Only use the SmartClean system with the original cleaning cartridge.
- Always place the SmartClean system on a stable, level and horizontal
surface to prevent leakage.
- Always make sure that the cartridge compartment is closed before you
use the SmartClean system to clean or charge the shaver.
- When the SmartClean system is ready for use, do not move it to
prevent leakage of cleaning uid.
- The SmartClean system thoroughly cleans but does not disinfect your
shaver, therefore do not share the shaver with others.
- Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the appliance.
- Water may leak from the socket at the bottom of the shaver when you
rinse it.This is normal and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.
Compliance with standards
- This shaver is waterproof and complies with the internationally
approved safety regulations. It is suitable for use in the bath or shower
and for cleaning under the tap. For safety reasons, the shaver can
therefore only be used cordlessly.
- The shaver and the SmartClean system comply with all applicable
standards and regulations regarding exposure to electromagnetic elds.
General
- The adapter is equipped with an automatic voltage selector and is
suitable for mains voltages ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe low voltage of less
than 24 volts.
- Maximum noise level: Lc = 69dB(A)
ENGLISH 5

The display
Note: Before you use the shaver for the rst time, remove the protective foil
from the display.
The various shaver types have different displays, which are shown in the
gures below.
- S95XX/S93XX
Personal settings
The appliance has a feature that allows you to personalise your settings.
You can choose between three settings depending on your personal
shaving needs: comfort, dynamic or efciency.
- When you press the - or + buttons, the bar lights up white
continuously.
Charging
- Charging takes approx. 1 hour.
Note: This appliance can only be used cordlessly.
- When the shaver is connected to the mains, you hear a sound. First the
bottom light ashes white then lights up white continuously. Then the
second light ashes and then lights up continuously, and so on until the
shaver is fully charged.
- Quick charge: When the bottom light stops ashing and lights up
continuously, the shaver contains enough charge for one shave.
Battery fully charged
Note: This appliance can only be used cordlessly.
Note: When the battery is full, the display switches off automatically after
30 minutes. When you press the on/off button during or after charging,
you hear a sound to indicate that the shaver is still connected to the mains.
- When the battery is fully charged, all lights of the battery charge
indicator light up white continuously.
ENGLISH6

Battery low
- When the battery is almost empty, the bottom light ashes orange and
you hear a sound.
Remaining battery capacity
- The remaining battery capacity is indicated by the lights of the battery
charge indicator that light up continuously.
Cleaning reminder
For optimal shaving performance, we advise you to clean the shaver after
every use.
- When you switch off the shaver, the cleaning reminder ashes to
remind you to clean the shaver.
Travel lock
You can lock the shaver when you are going to travel.The travel lock
prevents the shaver from being switched on by accident.
Activating the travel lock
1 Press the on/off button for 3 seconds to enter the travel lock mode.
,While you activate the travel lock, the travel lock symbol lights up
white continuously.When the travel lock is activated, the shaver
produces a sound and the travel lock symbol ashes.
Deactivating the travel lock
1 Press the on/off button for 3 seconds.
ENGLISH 7

,The travel lock symbol ashes and then lights up continuously.
The shaver is now ready for use again.
Note: You can also deactivate the travel lock by connecting the appliance to
the mains.
Replacing shaving heads
For maximum shaving performance, we advise you to replace the shaving
heads every two years.
- The appliance is equipped with a replacement reminder which reminds
you to replace the shaving heads.The replacement reminder lights up
white continuously and the arrows ash white. You hear a beep to
indicate you have to replace the shaving heads.
Note: After replacing the shaving heads, you need to reset the shaver by
pressing the on/off button for 7 seconds.
Exclamation mark
Blocked shaving heads
- If the shaving heads are blocked, the exclamation mark lights up orange
continuously.The replacement reminder and the cleaning reminder
ash white alternately and you hear a sound. In this case, the motor
cannot run because the shaving heads are soiled or damaged.
- When this happens, you have to clean the shaving heads or replace
them.
Overheating
- If the appliance overheats during charging, the exclamation mark ashes
orange.
- When this happens, the shaver automatically switches off. Charging
continues once the appliance is back to the normal temperature.
ENGLISH8

Charging
Charging takes approx. 1 hour.
A fully charged shaver has a shaving time of up to 50 minutes.
Note: You cannot use the appliance while charging.
Charge the shaver before you use it for the rst time and when the display
indicates that the battery is almost empty .
Charging with the adapter
1 Make sure the appliance is switched off.
2 Insert the small plug into the appliance (1) and put the adapter in
the wall socket (2).
Charging in the SmartClean system
1 Put the small plug in the SmartClean system.
2 Put the adapter in the wall socket.
3 Press the top cap to be able to place the shaver in the holder
(‘click’).
4 Hold the shaver upside down above the holder. Make sure the front
of the shaver points towards the SmartClean system.
5 Place the shaver in the holder (1), tilt the shaver backwards (2) and
press down the top cap to connect the shaver (‘click’) (3).
Note: The battery symbol lights up to indicate the appliance is charging.
ENGLISH 9

Using the shaver
Shaving
Skin adaptation period
Your rst shaves may not bring you the result you expect and your skin
may even become slightly irritated.This is normal.Your skin and beard need
time to adapt to any new shaving system.
We advise you to shave regularly (at least 3 times a week) with this shaver
for a period of 3 weeks to allow your skin to adapt to the new shaver.
Tip: To ensure the best result, we advise you to pre-trim your beard if you have
not shaved for 3 days or longer.
Note: This appliance can only be used cordlessly.
1 Press the on/off button once to switch on the shaver.
Tip: Select your personal settings (see chapter ‘The display’).
,The display lights up for a few seconds.
2 Move the shaving heads over your skin in circular movements.
- Do not make straight movements.
3 Press the on/off button once to switch off the shaver.
,The display lights up for a few seconds and then shows the remaining
battery charge.
Wet shaving
You can also use this shaver on a wet face with shaving foam or shaving gel.
To shave with shaving foam or shaving gel, follow the steps below:
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to your skin.
3 Rinse the shaving unit under the tap to ensure that the shaving unit
glides smoothly over your skin.
4 Press the on/off button once to switch on the shaver.
ENGLISH10

5 Move the shaving heads over your skin in circular movements.
Note: Rinse the shaver under the tap regularly to ensure that it continues to
glide smoothly over your skin.
6 Dry your face and thoroughly clean the shaver after use (see chapter
‘Cleaning and maintenance’).
Note: Make sure you rinse all foam or shaving gel off the shaver.
Using the click-on attachments
Using the trimmer attachment
You can use the trimmer attachment to groom your sideburns and
moustache.
1 Pull the shaving unit straight off the appliance.
Note: Do not twist the shaving unit while you pull it off the appliance.
2 Insert the lug of the trimmer attachment into the slot in the top of
the shaver.Then press down the trimmer attachment to attach it to
the appliance (‘click’).
3 Press the on/off button once to switch on the appliance.
,The display lights up for a few seconds.
4 You can now start trimming.
5 Press the on/off button once to switch off the appliance.
,The display lights up for a few seconds to show the remaining
battery charge.
6 Pull the trimmer attachment straight off the appliance.
Note: Do not twist the trimmer attachment while you pull it off the appliance.
7 Insert the lug of the shaving unit into the slot in the top of the
appliance.Then press down the shaving unit to attach it to the
appliance (‘click’).
ENGLISH 11

Using the beard styler attachment
1 Make sure the appliance is switched off.
2 Pull the shaving unit straight off the appliance.
Note: Do not twist the shaving unit while you pull it off the appliance.
3 Insert the lug of the beard styler attachment into the slot in the top
of the appliance.Then press down the beard styler attachment to
attach it to the appliance (‘click’).
Using the beard styler attachment with comb
You can use the beard styler attachment with the comb attached to style
your beard at one xed setting, but also at different length settings. The hair
length settings on the beard styler attachment correspond to the remaining
hair length after cutting and range from 1 to 5mm.
1 Slide the comb straight into the guiding grooves on both sides of the
beard styler attachment (‘click’).
2 Press the length selector and then push it to the left or right to
select the desired hair length setting.
3 Press the on/off button once to switch on the appliance.
4 You can now start styling your beard.
Using the beard styler attachment without comb
You can use the beard styler attachment without the comb to contour
your beard, moustache, sideburns or neckline.
1 Pull the comb off the beard styler attachment.
ENGLISH12

Note: Grab the comb in the centre to pull it off the beard styler attachment.
Do not pull at the sides of the comb.
2 Press the on/off button once to switch on the appliance.
3 You can now start contouring your beard, moustache, sideburns or
neckline.
Cleaning and maintenance
Cleaning the shaver in the SmartClean system
- SmartClean system Plus has two phases: the rinsing phase and the
drying phase.
Preparing the SmartClean system for use
Do not tilt the SmartClean to prevent leakage.
Note: Hold the SmartClean while you prepare it for use.
1 Put the small plug in the back of the SmartClean system.
2 Put the adapter in the wall socket.
3 Press the button on the side of the SmartClean system (1) and lift
the top part of the SmartClean system (2).
ENGLISH 13

4 Pull the seal off the cleaning cartridge.
5 Place the cleaning cartridge in the SmartClean system.
6 Push the top part of the SmartClean system back down (‘click’).
Using the SmartClean system
Always make sure to shake excess water off the shaver before you place
it in the SmartClean.
1 Press the top cap to be able to place the shaver in the holder
(‘click’).
ENGLISH14

2 Hold the shaver upside down above the holder. Make sure the front
of the shaver points towards the SmartClean system.
3 Place the shaver in the holder (1), tilt the shaver backwards (2) and
press down the top cap to connect the shaver (‘click’) (3).
,The battery symbol and the on/off button start to ash, which
indicates that the shaver is charging.
4 Press the on/off button on the SmartClean system to start the
cleaning program.
,The on/off button and the rinsing symbol both light up continuously.
Note: The rinsing phase takes approx. 10 minutes.
,During the drying phase, the drying symbol lights up continuously.
Note: The drying phase takes approx. 4 hours.
,When the cleaning program has been completed, the ready symbol
lights up continuously.
,The battery symbol lights up continuously to indicate that the shaver
is fully charged.
Note: Charging takes approx. 1 hour.
Note: If you press the on/off button of the SmartClean system during the
cleaning program, the program aborts. In this case, the rinsing or drying symbol
stops ashing.
Note: If you remove the adapter from the wall socket during the cleaning
program, the program aborts.
Note: 30 minutes after the cleaning program and charging have been
completed, the SmartClean switches off automatically.
ENGLISH 15

Replacing the cartridge of the SmartClean System
- Replace the cleaning cartridge when the replacement symbol ashes
orange or when you are no longer satised with the result.
1 Press the button on the side of the SmartClean system (1) and lift
the top part of the SmartClean system (2).
2 Take the empty cleaning cartridge from the SmartClean system and
pour any remaining cleaning uid out of the cleaning cartridge.
You can simply pour the cleaning uid down the sink.
3 Throw away the empty cleaning cartridge.
4 Unpack the new cleaning cartridge and pull the seal off the cartridge.
5 Place the new cleaning cartridge in the SmartClean system.
6 Push the top part of the SmartClean system back down (‘click’).
Cleaning the shaver under the tap
Clean the shaver after every shave for optimal shaving performance.
Be careful with hot water.Always check if the water is not too hot, to
prevent your hands from getting burnt.
Never dry the shaving unit with a towel or tissue, as this may damage the
shaving heads.
ENGLISH16

1 Switch off the shaver.
2 Rinse the shaving unit under a warm tap for some time.
3 Pull the shaving head holder off the bottom part of the shaving unit.
4 Rinse the shaving head holder under a warm tap.
5 Carefully shake off excess water and let the shaving head holder dry.
6 Reattach the shaving head holder to the bottom part of the shaving
unit (‘click’).
Thorough cleaning method
Make sure the appliance is switched off.
1 Pull the shaving head holder off the bottom part of the shaving unit.
2 Place the retaining ring holder on the retaining ring (1), turn it
anticlockwise (2) and lift it off the shaving head (3).
Remove the retaining ring from the retaining ring holder and repeat this
process for the other retaining rings.
ENGLISH 17

3 Remove the shaving heads from the shaving head holder. Each shaving
head consists of a cutter and guard.
Note: Do not clean more than one cutter and guard at a time, since they are
all matching sets. If you accidentally put a cutter in the wrong shaving guard,
it may take several weeks before optimal shaving performance is restored.
4 Clean the cutter and guard under the tap.
5 After cleaning, place the cutter back into the guard.
6 Put the shaving heads back into the shaving head holder.
Note: Make sure the projections of the shaving heads t exactly into the
recesses.
7 Place the retaining ring holder on the retaining ring (1), place it
on the shaving head (2) and turn it clockwise (3) to reattach the
retaining ring.
Repeat this process for the other retaining rings.
8 Reattach the shaving head holder to the bottom part of the
shaving unit.
ENGLISH18

Cleaning the click-on attachments
Cleaning the trimmer attachment
Clean the trimmer attachment every time you have used it.
1 Switch on the appliance with the trimmer attachment attached.
2 Rinse the trimmer attachment under a hot tap for some time.
3 Carefully shake off excess water and let the trimmer attachment dry.
4 After cleaning, switch off the appliance.
Tip: For optimal trimmer performance, lubricate the trimmer teeth with a drop
of sewing machine oil every six months.
Cleaning the beard styler attachment
Clean the beard styler attachment every time you have used it.
1 Pull the comb off the beard styler attachment.
2 Rinse the beard styler attachment and the comb separately under a
hot tap for some time.
3 Carefully shake off excess water and let the beard styler
attachment and comb dry.
4 Lubricate the teeth with a drop of sewing machine oil every
six months.
Storage
1 Store the shaver in the pouch supplied.
Note: We advise you to let the shaver dry before you store it in the pouch.
Replacement
Replacing the shaving heads
For maximum shaving performance, we advise you to replace the shaving
heads every two years.
Replacement reminder
The shaving unit symbol lights up to indicate that the shaving heads need to
be replaced. Replace damaged shaving heads right away.
Only replace the shaving heads with original SH90 Philips shaving heads.
ENGLISH 19

1 The shaving unit symbol lights up continuously, the arrows ash
white and you hear a beep when you switch off the shaver.
2 Pull the shaving head holder off the bottom part of the shaving unit.
3 Place the retaining ring holder on the retaining ring (1), turn it
anticlockwise (2) and lift it off the shaving head (3).
Remove the retaining ring from the retaining ring holder and repeat this
process for the other retaining rings.
4 Remove the shavings heads from the shaving head holder and throw
them away.
5 Place new shaving heads in the holder.
Note: Make sure the projections of the shaving heads t exactly into the
recesses.
ENGLISH20