Philips S3000 Series User manual

S3000

1
2
3
4
5 6
7
8
9
10
11
12

empty page before TOC

English 6
Français (Canada) 22

English
6English
General description (Fig. 1)
1 Protection cap
2 Shaving unit
3 Shaving unit release button
4 On/off button
5 1-level battery status indicator (S3133, S3134 only)
6 3-Level battery status indicator (S3233, S3230, S3332,
S3333 only)
7 Socket for small plug
8 Charging stand (S3332, S3333 only)
9 Pop-up trimmer
10 Trimmer release slide
11 Supply unit
12 Small plug
13 Storage pouch (S3232, S3230, S3332, S3333 only)
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips
offers, register your product at
www.philips.com/welcome.
Important safety information
Only use the product for its intended purpose. Read this
important information carefully before you use the
product and its batteries and accessories, and save it for
future reference. Misuse can lead to hazards or serious
injuries.
Warning
- Keep the supply unit and the charging stand dry.

7
English
- This shaver is waterproof. It is suitable for use in the
bath or shower and for cleaning under the tap. For
safety reasons, the shaver can therefore only be used
without cord.
- Do not modify the supply unit.
- This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without
supervision.
- Do not use a damaged appliance. Replace damaged
parts with new Philips parts.
- Do not use the supply unit in or near wall sockets that
contain an electric air freshener to prevent irreparable
damage to the supply unit.
- Because of hygiene, only one person should use the
appliance.
- Unplug the appliance before cleaning it with water.
- Only use cold or lukewarm water to clean the
appliance.
- Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids to clean the
appliance.
- Water may drip from the socket at the bottom of the
shaver when you rinse it. This is normal and not
dangerous because all electronics are enclosed in a
sealed power unit inside the shaver.
- Only use original Philips accessories or consumables.
Only use detachable supply unit HQ8505.
- Charge, use and store the product at a temperature
between 5°C and 35°C.
- Keep product and batteries away from fire and do not
expose them to direct sunlight or high temperatures.
- If the product becomes abnormally hot or smelly,
changes color or if charging takes longer than usual,
stop using and charging the product and contact
Philips.

8English
- Do not place products and their batteries in
microwave ovens or on induction cookers.
- Do not open, modify, pierce, damage or dismantle the
product or battery to prevent batteries from heating
up or releasing toxic or hazardous substances. Do not
short-circuit, overcharge or reverse charge batteries.
- If batteries are damaged or leaking, avoid contact
with the skin or eyes. If this occurs, immediately rinse
well with water and seek medical care.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
The display
S313X
Battery fully charged
When the battery is fully charged, the charging light
lights up white continuously.
Note: After approx. 30 minutes, the charging light goes
out to save energy.
Battery low
=
When the battery is almost empty (when there are only 5
or fewer shaving minutes left), the charging light flashes
orange.
When you switch off the appliance, the charging light
continues to flash orange for a few seconds.

9
English
Charging
When the shaver is charging, the charging light flashes
white.
S323X, S333X
Battery fully charged
When the battery is fully charged, all charging lights light
up white continuously.
Note: After approx. 30 minutes, the charging lights go
out to save energy.
Battery low
=
When the battery is almost empty (when there are only 5
or fewer shaving minutes left, the bottom charging light
flashes orange.
When you switch off the appliance, the bottom charging
light continues to flash orange for a few seconds.
Charging
When the shaver is charging, first the bottom light of the
battery charge indicator flashes, then the second light,
and so on until the shaver is fully charged.
Charging
Charge the shaver before you use it for the first time and
when the display indicates that the battery is almost
empty.
Charging takes approx. 1 hour. A fully charged shaver has
a shaving time of up to 60 minutes.

10 English
This shaver is suitable for use in the bath or
shower. For safety reasons, it is therefore not
possible to use the shaver while it is connected to
the power outlet for charging.
Note: Depending on your shaving/styling behavior and
beard type, the operating time may vary over time.
Charging with the supply unit
2
1
1Put the small plug in the appliance.
2Put the supply unit in the wall socket.
- The charging light shows the charging status of the
appliance.
3After charging, remove the supply unit from the wall
socket and pull the small plug out of the appliance.
Charging with charging stand (S3332, S3333 only)
1Connect the small plug of the cord into the charging
stand. Connect the supply unit into any 100V to 240V
outlet. Use only the power cord provided.
2Place the shaver in the stand in an upright position
making sure charging contacts in the bottom of stand
fit into recess in bottom of the shaver.
- The display on the shaver will indicate the shaver is
charging.
3After charging, remove the shaver from the stand by
lifting straight up. Do not tilt the shaver.
Quick charge
When you start charging the empty battery, the charging
light flashes white quickly. After approx. 5 minutes the
charging light flashes white slowly. The shaver now
contains enough energy for a 5-minute shave.
Using the appliance
Note: This appliance is waterproof. It is suitable for use in
the bath or shower and for cleaning under the tap. For
safety reasons, this appliance can therefore only be used
without cord.

11
English
This symbol indicates that the shaver can be used in the
bath or shower.
Shaving tips and tricks
- Make circular movements during use. Circular
movements provide better shaving results than
straight movements.
- Your skin may need 2 or 3 weeks to get accustomed
to the Philips shaving system.
Switching the appliance on and off
To switch the appliance on or off, press the on/off button
once.
Shaving
Dry shaving
Note: For the best results on skin comfort, pre-trim
your beard if you have not shaved for 3 days or
longer.
1Switch on the appliance.

12 English
2Move the shaving heads over your skin in circular
movements to catch all hairs growing in different
directions.
3Stretch your skin with your free hand so the blades
can lift and cut hair. Gently press the shaver onto you
skin so the floating heads can follow the contours of
your face.
Note: Do not press too hard as too much pressure can
cause shaving heads to pinch the skin.
4Switch off and clean the appliance after each use.
5Put the protective cap on the appliance to protect the
shaving heads during storage and travel.
Wet shaving
For a more comfortable shave, you can also use this
appliance on a wet face with shaving foam or shaving
gel.
1Apply some water to your skin.
2Apply shaving foam or gel to your skin.
3Rinse the shaving unit under the tap to ensure that it
glides smoothly over your skin.
4Switch on the appliance.

13
English
5Move the shaving heads over your skin in circular
movements to catch all hairs growing in different
directions. Make sure each shaving head is fully in
contact with the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, this can cause skin
irritation.
Note: Rinse the shaving unit regularly to ensure that it
continues to glide smoothly over your skin.
6Switch off and clean the appliance after each use.
7Dry your face.
Note: Make sure that you rinse all foam or shaving gel
off the appliance with warm water.
8Put the protective cap on the appliance to protect the
shaving heads during storage and travel.
Trimming
You can use the trimmer to groom your sideburns and
moustache.
1Push the trimmer release slide downwards to open
the trimmer.
2Switch on the appliance.
3Hold the trimmer perpendicular to the skin and move
the appliance downwards while you exert gentle
pressure.
4Switch off and clean the trimmer after each use.
5Close the pop-up trimmer (‘click’).

14 English
Cleaning and maintenance
Cleaning the shaver
Clean the shaver after every use for optimal performance.
Caution: Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids such as
petrol or acetone to clean the appliance.
Caution: While rinsing the shaving heads, water may
drip out of the base of the appliance. This is a normal
occurrence. Internal electric parts are in a waterproof
compartment so the appliance will be protected
against water damage.
1Switch off the appliance and make sure it is
disconnected from the wall socket.
2Press the release button to open the shaving unit.
3Rinse the shaving unit and hair chamber with
lukewarm water.
4Rinse the outside of the shaving unit with lukewarm
water.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
5Carefully shake off excess water and let air dry
completely.
6Close the shaving unit.
Cleaning the pop-up trimmer
Clean the pop-up trimmer after each use.
Never dry the trimmer teeth with a towel or tissue, as
this may damage the trimmer teeth.

15
English
1Switch off the appliance and make sure it is
disconnected from the wall socket.
2Push the trimmer release slide downwards to open
the trimmer.
3Switch on the appliance and rinse the pop-up trimmer
with warm water.
4After cleaning, switch off the appliance.
5Carefully shake off excess water and let the pop-up
trimmer air dry.
6Close the pop-up trimmer (‘click’).
Tip: For optimal performance, lubricate the teeth of the
pop-up trimmer with a drop of mineral oil every six
months (oil not included).
Thorough cleaning
Clean the shaving heads thoroughly once a month for
optimal performance.
1Switch off the appliance and make sure it is
disconnected from the wall socket.
2Press the release button to open the shaving unit. Pull
the shaving unit off the appliance.
2
1
3Turn the lock anticlockwise (1) and remove the
retaining frame (2). Place it aside in a safe place.

16 English
4Remove and clean one shaving head at a time. Each
shaving head consists of a cutter and a guard.
Note: Do not clean more than one cutter and guard at
a time, since they are all matching sets. If you
accidentally mix up the cutters and guards, it may
take several weeks before optimal shaving
performance is restored.
5Remove the cutter from the shaving guard and clean
both parts under the tap.
6Put the cutter back into the guard.
7Put the shaving heads back into the shaving unit.
1
2
8Put the retaining frame back into the shaving unit (1)
and turn the lock clockwise (2).

17
English
9Insert the hinge of the shaving unit into the slot in the
top of the shaver. Then close the shaving unit.
Note: If the shaving unit does not close smoothly,
check if you have inserted the shaving heads properly
and if the retaining frame is locked.
Replacement
Replacing the shaving heads
2yrs
For maximum shaving performance, we advise you to
replace the shaving heads every two years. Replace
damaged shaving heads immediately. Always replace the
shaving heads with original Philips shaving heads (see
'Ordering accessories').
1Switch off the appliance and make sure it is
disconnected from the wall socket.
2Press the shaving unit release button to open the
shaving unit. Pull the shaving unit off the appliance.
2
1
3Turn the lock anticlockwise (1) and remove the
retaining frame (2). Place it aside in a safe place.
4Remove the shaving heads from the shaving unit.
Discard the used shaving heads immediately to avoid
mixing them with the new shaving heads.

18 English
5Place new shaving heads in the shaving unit.
Note: Make sure that the shaving heads with the
projections fit exactly onto the hooks of the shaving
head holder when placing them. The shaving heads
supplied with the shaver either have notches or
projections. Both shaving systems are the same.
1
2
6Put the retaining frame back into the shaving unit (1)
and turn the lock clockwise (2).
7Insert the hinge of the shaving unit into the slot in the
top of the shaver. Then close the shaving unit.
Note: If the shaving unit does not close smoothly,
check if you have inserted the shaving heads properly
and if the retaining frame is locked.
Storage
Put the protection cap on the shaver to prevent damage.
Note: Always let the shaver dry completely before storing
or before charging in the charging stand.
Storage in pouch (S3232, S3230, S3332, S3333 only)
- Store the appliance in the pouch supplied.
- Make sure the appliance is dry before you store it in
the pouch.

19
English
Ordering accessories
To buy accessories or spare parts, visit
www.philips.com/parts-and-accessories or go to your
Philips dealer. You can also contact the Philips Consumer
Care Center in your country (see the international
warranty leaflet for contact details).
Support
For all product support such as frequently asked
questions, please visit www.philips.com/support.
The shaving heads (cutters and guards) are not covered
by the terms of the international warranty because they
are subject to wear.
Disposal
- This product contains a rechargeable lithium-ion
battery which must be disposed of properly.
- Contact your local town or city officials for battery
disposal information. You can also call 888-224-9764
or visit www.call2recycle.ca for battery drop-off
locations.
- For assistance, visit our website
www.philips.com/support or call [phone]
toll free.
- Your product is designed and manufactured with
high quality materials and components, which can be
recycled and reused. For recycling information, please
contact your local waste management facilities or visit
www.recycle.philips.com.
Removal of built-in rechargeable battery
The built-in rechargeable battery must only be removed
by a qualified professional when the appliance is
discarded. Before removing the battery, make sure that
the appliance is disconnected from the wall socket and
that the battery is completely empty.
Take any necessary safety precautions when you
handle tools to open the appliance and when you
dispose of the rechargeable battery.

20 English
When you handle batteries, make sure that your
hands, the product and the batteries are dry.
To avoid accidental short-circuiting of batteries
after removal, do not let battery terminals come
into contact with metal objects (e.g. coins,
hairpins, rings). Do not wrap batteries in
aluminum foil. Tape battery terminals or put
batteries in a plastic bag before you discard them.
Be careful, the battery strips are sharp.
1Press the shaving unit release button to open the
shaving unit. Pull the shaving unit off the shaver.
2Remove the screw in the back of the shaver.
3Remove the back panel by using a flathead
screwdriver.
2×