Philips 42FD9932-69S User manual

Printed on recycled paper

Printed in Belgium 3104 315 2050.1
Printed on recycled paper

4
4
x 2
a
b

406mm /16"
73mm /2.87"
5
5
10
x 4x 4

ab
6
x 6

MAINS INLET
VGA IN
AUDIO IN
L
R
VGA OUT
5
1 32 42
AUDIO OUT

1
English
Unpacking and wall mounting instructions
For the unpacking instructions follow the illustrated steps printed on the
packaging (outside and inside).
For the wall mounting instructions follow the illustrated steps ‘to §
printed on the first pages of this instruction booklet.
Make sure that the wall mount is being fixed securely enough so that it meets
safety standards.The weight of the monitor (excl. packaging) is about 43 kg.
Connect your computer
& Connect one end of the VGA cable 1supplied to the video card of the
computer and the other end to the VGA IN connector at the rear side of the
monitor. Fix the connectors firmly with the screws on the plug.
é In case of a Multimedia computer, connect the audio cable 2to the audio
outputs of your Multimedia computer and to the AUDIO IN R (right) and L
(left) inputs of the monitor.
Daisy chaining
The Active Loop Through facility makes it possible to make a daisy chain with
a second VGA monitor.
“Connect one end of another VGA cable 3to the VGA OUT connector at
the rear side of the monitor and the other end to the VGA IN connector of a
second VGA monitor.
‘In case of a Multimedia computer, also connect the audio cables 4to the
AUDIO L and R outputs of the monitor and to the AUDIO IN L and Rinputs
of the second VGA monitor.
Note: only use the VGA cables supplied or use cables that are specially delivered
with the monitor.
Connect your Apple Macintosh* computer
Attention: Macintosh computers with separate H and V synchronisation signals
can be used together with a switchable adaptor. Macintosh computers with
Composite Sync and Sync on Green signals may need another special adaptor or
cable. Contact your dealer.
Connect the switchable adaptor for Apple video connectors to one end of a
VGA cable.
Put the DIP switches on the adaptor in the following positions :
1234
off off on on
Connect the end of the VGA cable with the adaptor to the video card of the
computer and the other end to the VGA IN connector on the back of the
monitor.
Screw the connectors down firmly.
* Apple Macintosh is a registered trademark of Apple Computer, Inc.
15-pin D sub
(2-row) 15-pin mini D sub (3-row)
a

2
VGA 640x480 31.468 kHz 60 Hz
VGA 640x400 31.468 kHz 70 Hz
VGA 640x350 31.468 kHz 70 Hz
VGA 856x480 31.468 kHz 60 Hz
VGA 800x450 31.490 kHz 65 Hz
MAC II 640x480 35.000 kHz 67 Hz
SVGA 800x600 35.156 kHz 56 Hz
SVGA 800x600 37.880 kHz 60 Hz
XGA 1024x768 45.000 kHz 56 Hz
XGA 1024x768 48.360 kHz 60 Hz
When a VGA computer is connected, the selection is made automatically.
A message is displayed when the monitor does not support one of the above
mentioned VGA modes.
Switch your computer to a correct display mode.
&Insert the mains plug 5(see previous page for the illustration) supplied
into the mains inlet at the back of the monitor and in the wall socket.
Please, only use the supplied rim-earthed mains cord with its built-in filter.
éRemote control: remove the cover of the battery compartment.
Insert the 2 batteries supplied (Type LR6AA-1.5V).
The batteries supplied do not contain the heavy metals mercury and cadmium.
Nevertheless in many countries batteries may not be disposed of with your house-
hold waste. Please check on how to dispose of batteries according to local regula-
tions.
“Switch the monitor on : Press the power button Bat the right side of
the monitor.
A green indicator lights up and the screen comes on.
When the monitor does not receive a certain VGA signal the screen switches
to standby and the red indicator lights up.
Make sure that your PC is switched on and is in the correct display mode.
B
Use of the remote control
Computer Display modes
Operation