Philips MasterColor 404939 User manual

◗Ordering Information
Ordering Code CDM20/TC/830
ANSI Designation C156/C175/E
Product Number 404939
Description MasterColor Ceramic
Metal Halide
Package Quantity 12
◗Physical Characteristics
Bulb Size T-4
Bulb Finish Clear
Base G-8.5 Bi-Pin
Max. Overall ength (MO ) 3.35'' (85mm)
ight Center ength ( C ) 2.0'' (52mm)
Arc ength 0.12'' (3mm)
Arc Tube Material Polycrystalline Alumina
Max. Permissible Bulb Temp. 320ºC (608ºF)
Max. Permissible Pinch Temp. 300ºC (572ºF)
Max.Arc Tube to Base Eccentricity 3º
◗Operating Characteristics (Photometric)
Rated Initial umens11650
Mean umens,Approx.21175
Rated Average ife, Hours312,000
Correlated Color Temp. (CCT)23000K
CIE Chromaticity Approx.2x-.430, y-.385
Color Rendering Index (CRI) 85
Efficacy (lpw) 75
◗Operating Position
Universal—Enclosed uminaires Only
Note: Operate lamp only on approved thermally protected electronic ballast.
MasterColor®Ceramic Metal Halide
22 Watt 3000K Tubular Single-Ended T4 amps
with FadeBlock™UV Filtering
311/32''

Philips Lighting Company
200 Franklin Square Drive
P.O. Box 6800
Somerset, NJ 08875-6800
1-800-555-0050
ADivision of Philips Electronics North America Corporation
Updated 3/09 TDS-404939
Philips Lighting
281 Hillmount oad
Markham, Ontario
Canada L6C 2S3
1-800-555-0050
A Division of Philips Electronics td.
www.philips.com
MasterColor®Ceramic Metal Halide 22 Watt 3000K Tubular Single-Ended T4 amps with FadeBlock™UV Filtering
Electrical Data (Subject to change without notice)
LampWatts(Nominal).............................22
Lamp Operating Voltage (rms) (Nominal)2.............100
Initial Lamp Voltage ange (rms)3.....................95–108
Lamp Operating Current (Amps) (rms) (Nominal) . . . . . 0.22
Lamp Current Crest Factor (Maximum) . . . . . . . . . . . . . . 1.8
Warm-up Time to 80% of Output . . . . . . . . . . . . . . . . . . . 3 Minutes
estrike Time for Hot Lamp. . . . . . . . . . . . . . . . . . . . . . . . . 4–8 Minutes
BallastType.......................................C156/C175/E
Ballast Open Circuit Voltage (Minimum). . . . . . . . . . . . . . . 250
PulsePeakVolts...................................3000Min.,4000Max.
Pulse Width @ 90% Peak . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Micro Second Min.
Pulse epetition ate (Minimum)4....................1perHalfCycle
Minimum Operating Temperature . . . . . . . . . . . . . . . . . . . . -30ºC
1) Measured at 100 hours of life in vertical position.
2) Measured at rated lamp watts on a linear reactor. LPW does not include ballast losses.
3) Measured with the lamp operating at rated watts.
4) Option-Pulse Width @ 90% Peak, 1 micro second minimum with 2 pulses per half cycle.
INSTALLATION INFO MATION
MasterColor®Metal Halide T4 lamps must be used in combination with appropriate fully electronic ballast.
Warnings, Cautions and Operating Instructions
“WA NING: These lamps can cause serious skin burn and eye inflammation
from short wave ultraviolet radiation if outer envelope of the lamp is broken or
punctured. Do not use where people will remain for more than a few minutes unless
adequate shielding or other safety precautions are used. Certain lamps that will
automatically extinguish when the outer envelope is broken or punctured are
commercially available." This lamp complies with FDA radiation performance
standard 21 CFR subchapter J. (USA:21CFR 1040.30 Canada:SOR/DORS/80-381)
If the outer bulb is broken or punctured, turn off at once and replace
the lamp to avoid possible injury from hazardous short wave ultraviolet
radiation. Do not scratch the outer bulb or subject it to pressure as this
could cause the outer bulb to crack or shatter.A partial vacuum in the
outer bulb may cause glass to fly if the envelope is struck.
WA NING: The arc-tube of metal halide lamps are designed to operate under
high pressure and at temperatures up to 1000ºC and can unexpectedly rupture due
to internal or external factors such as a ballast failure or misapplication. If the
arc-tube ruptures for any reason, the outer bulb may break and pieces of extremely
hot glass might be discharged into the surrounding environment. If such a rupture
were to happen, THE E IS A ISK OF PE SONAL INJU Y, P OPE TY
DAMAGE, BU NS AND FI E.
Certain lamps that will retain all the glass particles should inner arc-tube
rupture occur are commercially available from Philips Lighting Company.
ELAMP FIXTU ES AT O BEFO E THE END OF ATED LIFE.
Allowing lamps to operate until they fail is not advised and may increase
the possibility of inner arc tube rupture.
This lamp contains an arc tube with a filling gas containing less than
10 nCi of Kr-85 and is distributed by Philips Lighting Company, a division
of Philips Electronics North America Corporation, Somerset,
New Jersey, 08875.
CAUTION: TO REDUCE THE RISK OF PERSONA INJURY, PROPERTY
DAMAGE, BURNS AND FIRE RESU TING FROM AN ARC-TUBE RUPTURE THE
FO OWING AMP OPERATING INSTRUCTIONS MUST BE FO OWED.
Lamp Operating Instructions:
1)RE AMP FIXTURES AT OR BEFORE THE END OF RATED IFE.
Allowing lamps to operate until they fail is not advised and may increase
the possibility of inner arc tube rupture.
2) Use only in fully enclosed fixtures capable of withstanding particles of glass
having temperatures up to 1000°C. ens/diffuser material must be heat
resistant. Consult fixture manufacturer regarding the suitability of the fixture
for this lamp.
3) Do not operate a fixture with a missing or broken lens/diffuser.
4) Operate lamp only within specified limits of operating position.
5)Before lamp installation/replacement, shut power off and allow lamp and
fixture to cool to avoid electrical shock and potential burn hazards.
6) Use only auxiliary equipment meeting Philips and/or ANSI standards.
Use within voltage limits recommended by ballast manufacturer.
A. Operate lamp only within specified limits of operation.
B. For total supply load refer to to ballast manufacturer’s electrical data.
C. Operate CDM-T6 (G12 base) lamps only on thermally protected ballasts.
D. Operate CDM-TC lamps (G8.5 base), CDM-T6 Elite lamps, and CDM-T6
39W/842 lamps only on thermally protected electronic ballasts.
7) Periodically inspect the outer envelope. Replace any lamps that show
scratches, cracks or damage.
8) If a lamp bulb support is used, be sure to insulate the support electrically
to avoid possible decomposition of the bulb glass.
9) Protect lamp base, socket and wiring against moisture, corrosive
atmospheres and excessive heat.
10) Time should be allowed for lamps to stabilize in color when turned on
for the first time. This may require several hours of operation, with more
than one start. amp color is also subject to change under conditions of
excess vibration or shock, and color appearance may vary between
individual lamps.
11) amps may require 4–8 minutes to re-light if there is a power interruption.
12) Take care in handling and disposing of lamps. If an arc tube is broken, avoid
skin contact with any of the contents or fragments.