Philips LX9000R/25S User manual

DVD Recorder Home Entertainment System LX9000R
LX9000R

2
Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio LX 9000R Philips
risponde alle prescrizioni dell’art. 2 comma 1 del D. M.
28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer Electronics
Philips, Glaslaan 2
5616 JB Eindhoven,The Netherlands
Norge
Typeskilt finnes på apparatens bakside.
Observer: Nettbryteren er sekundert innkoplet. Den
innebygde netdelen er derfor ikke frakoplet nettet
så lenge apparatet er tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk støt, skal
apparatet ikke utsettes for regn eller fuktighet.

Technical data ––––––––––––––––––––––––––––––– 5
General information
Introduction ––––––––––––––––––––––––––––––––––– 6
Supplied Accessories –––––––––––––––––––––––––––– 6
Setup –––––––––––––––––––––––––––––––––––––––– 6
Maintenance ––––––––––––––––––––––––––––––––––– 6
Disc handling –––––––––––––––––––––––––––––––––– 6
Environmental information –––––––––––––––––––––––– 6
Which discs can be used? –––––––––––––––––––––––– 7
Region code ––––––––––––––––––––––––––––––––––– 7
Trademark and license information ––––––––––––––––– 7
Remote Control
Inserting the batteries ––––––––––––––––––––––––––– 8
Using the remote control –––––––––––––––––––––––– 8
Remote control keys –––––––––––––––––––––––––––– 9
Controls and connections
Controls on the front –––––––––––––––––––––––––– 10
Connections on the front ––––––––––––––––––––––– 10
Connections on the rear –––––––––––––––––––––––– 11
Speaker setup –––––––––––––––––––––––––––––– 12
Connecting …
Connecting the speakers –––––––––––––––––––––––– 12
Connecting the tuner antennas ––––––––––––––––––– 13
MW antenna –––––––––––––––––––––––––––––– 13
FM antenna ––––––––––––––––––––––––––––––– 13
Connecting theTV antenna –––––––––––––––––––––– 13
Connecting theTV ––––––––––––––––––––––––––––– 13
Connecting additional video appliances ––––––––––––– 14
Connecting additional audio appliances ––––––––––––– 14
Analogue connections ––––––––––––––––––––––– 14
Digital connections –––––––––––––––––––––––––– 14
Connecting a camcorder to CAM 1 or CAM 2 ––––––– 15
Connecting headphones –––––––––––––––––––––––– 15
Mains ––––––––––––––––––––––––––––––––––––––– 15
Initial installation
Basic settings ––––––––––––––––––––––––––––––––– 16
Advanced settings ––––––––––––––––––––––––––––– 17
System settings
When adding appliances or changing the
connections of appliances ––––––––––––––––––––––– 18
After changing the connection of theTV ––––––––– 18
After changing the connections of theVCR,
satellite receiver or game console –––––––––––––– 18
After changing the connections of the
CD recorder, CD player or tape deck ––––––––––– 19
System settings
When changing the speaker setup ––––––––––––––––– 19
Setting which speakers are connected ––––––––––– 19
Setting the distance of your listening position to
the speakers ––––––––––––––––––––––––––––––– 19
SearchingTV channels –––––––––––––––––––––––––– 20
Autom. Search ––––––––––––––––––––––––––––– 20
Manual search ––––––––––––––––––––––––––––– 20
Changing the order ofTV channels and
deletingTV channels ––––––––––––––––––––––––––– 21
FollowTV ––––––––––––––––––––––––––––––––– 21
SortTV channels ––––––––––––––––––––––––––– 21
AdditionalTV channel settings –––––––––––––––––––– 22
TV channel name ––––––––––––––––––––––––––– 22
TV system –––––––––––––––––––––––––––––––– 22
NICAM –––––––––––––––––––––––––––––––––– 22
Fine tuning –––––––––––––––––––––––––––––––– 22
Setting the time and date –––––––––––––––––––––––– 23
Using a connected decoder to decode aTV channel ––– 23
Source selection
Selecting a source ––––––––––––––––––––––––––––– 24
Selecting another source while recording ––––––––– 24
Switching between recorded and original
video and sound quality –––––––––––––––––––––– 24
Volume and sound
Adjusting the volume of all speakers ––––––––––––––– 25
Adjusting the volume of the rear speakers and the
subwoofer ––––––––––––––––––––––––––––––––––– 25
Adjusting bass and treble –––––––––––––––––––––––– 25
Loudness –––––––––––––––––––––––––––––––––––– 25
Setting the volume balance between the speakers –––– 25
Surround sound
Selecting a surround effect ––––––––––––––––––––––– 26
Adjusting 3D Surround and Natural Surround ––––––– 27
ClearVoice ––––––––––––––––––––––––––––––––––– 27
Night mode –––––––––––––––––––––––––––––––––– 27
Various
Demo mode ––––––––––––––––––––––––––––––––– 27
Radio tuner
Selecting a preset radio station ––––––––––––––––––– 28
Tuning to a radio station –––––––––––––––––––––––– 28
Storing radio stations ––––––––––––––––––––––––––– 28
Automatic searching and storing ––––––––––––––– 28
Manual searching and storing –––––––––––––––––– 28
Changing the order of stored radio stations ––––––––– 29
Switching between mono and stereo radio reception –– 29
RDS – Radio Data System ––––––––––––––––––––––– 29
Contents
3
English

Playback
Loading discs _________________________________ 30
Playing a DVD-Video disc _______________________ 30
Region code information _____________________ 30
Disc menu ________________________________ 30
Playing a (Super)Video CD ______________________ 31
PBC (Playback Control) ______________________ 31
What to do if PBC is deactivated? ______________ 31
Playing a DVD+R or DVD+RW disc _______________ 31
Playing a write protected DVD+R or DVD+RW disc
__ 31
Playing a DVD+R or DVD+RW disc that
is not write protected _______________________ 31
Playing an audio CD ____________________________ 32
Some words about MP3 ________________________ 32
Making your own MP3-CD ___________________ 32
Data rate _________________________________ 32
Recording an MP3-CD _______________________ 32
Supported formats __________________________ 32
Playing an MP3-CD ____________________________ 32
Playback features
Selecting a title/chapter _________________________ 33
Selecting a title directly _______________________ 33
Selecting a chapter directly ____________________ 33
Searching ____________________________________ 33
Searching via the menu bar ___________________ 33
Searching by keying in a time _____________________ 34
Scan ________________________________________ 34
Repeat and playback in random order ______________ 34
Repeating a specific sequence (not on MP3-CDs) _____ 34
Still picture ___________________________________ 35
Frame by frame playback ________________________ 35
Slow motion _________________________________ 35
Slow motion via the menu bar _________________ 35
Zoom ______________________________________ 36
Camera angle _________________________________ 36
Changing the audio language _____________________ 37
Subtitles _____________________________________ 37
Recording
Copyright protection ___________________________ 38
Discs for recording _____________________________ 38
Before you start recording _______________________ 38
Quick recording from theTV _____________________ 38
Recording from theTV or from another
additional appliance ____________________________ 39
Safe record __________________________________ 40
Recording with automatic stop (OTR -
OneTouch Recording) __________________________ 40
Lining up recordings within a title -
assemble cut (DVD+RW discs only) _______________ 40
Selecting the recording mode ____________________ 41
Selecting the recording mode via the menu _______ 41
Automatic recording from a satellite receiver ________ 42
Direct Record ________________________________ 43
Switching Direct Record on or off ______________ 43
Starting Direct Record _______________________ 43
Timer recording
VPS and PDC ________________________________ 44
NexTView Link _______________________________ 44
Programming a recording with the
ShowView®system ____________________________ 45
Programming a recording without the
ShowView®system ____________________________ 46
Checking, changing or deleting a timer recording ______ 47
Advanced features
Editing the name of the recording _________________ 48
Erasing an entire recording/title ___________________ 48
Disc info screen (DVD+R, DVD+RW discs only) _____ 49
How to display the disc info screen ________________ 49
Changing the disc name
(DVD+R, DVD+RW discs only) __________________ 49
Activating or deactivating the write protection
(DVD+R, DVD+RW discs only) __________________ 50
Making edits compatible (DVD+RW discs only) ______ 50
Finalising DVD+R discs _________________________ 51
Erasing an entire DVD+RW disc __________________ 51
Favorite Scene Selection menu ___________________ 52
Inserting chapter markers _______________________ 52
Deleting chapter markers _______________________ 52
Hiding chapters _______________________________ 53
Playing the entire title including hidden chapters ___ 53
Changing the index picture ______________________ 54
Dividing titles (on DVD+RW discs only) ____________ 54
User preferences
Picture ______________________________________ 55
Language ____________________________________ 56
Features _____________________________________ 57
Remote control settings _________________________ 57
Record settings _______________________________ 58
Installation ___________________________________ 58
Access control
Child lock (DVD-Video discs, (Super) Video CDs,
DVD+R discs, DVD+RW discs only) _______________ 59
Activating and deactivating the child lock _________ 59
Authorising a disc ___________________________ 59
Locking authorised discs ______________________ 59
Filter function and parental control
(DVD-Video discs only) _________________________ 60
Activating and deactivating the filter function ______ 60
Changing the country code (DVD-Video discs only) ___ 61
Changing the 4-digit code (DVD-Video discs, (Super)
Video CDs, DVD+R discs, DVD+RW discs only) _____ 61
If you have forgotten your 4-digit code __________ 61
Troubleshooting _________________________ 62–65
Contents
4
English

Subject to modification without notice.
General
Power supply rating ––––––––––––––––––– 230V / 50 Hz
Power consumption
Active ––––––––––––––––––––––––––––––– < 100 W
Standby –––––––––––––––––––––––––––––––– < 5 W
Record timer standby –––––––––––––––––––– < 17 W
Dimensions (w x h x d) –––– 435 mm x 96 mm x 405 mm
Weight –––––––––––––––––––––––––––––––––––– 9 kg
Amplifier
Output power
Stereo mode (1 kHz, 10%THD) –––––– 2 x 70 W RMS
Surround mode (1 kHz, 10% THD)
Front ––––––––––––––––––––––––– 2 x 81 W RMS
Centre ––––––––––––––––––––––––––– 81 W RMS
Surround –––––––––––––––––––––– 2 x 81 W RMS
Subwoofer –––––––––––––––––––––––– 81 W RMS
Total Harmonic Distortion ––––––––––– 10%, 1 kHz, 66 W
S/N ratio (unweighted) ––––––––––––––––––––– ≥92 dB
(A-weighted) –––––––––––––––––––––––––– 100 dBA
Stereo separation (1 kHz) –––––––––––––––––– ≥-50 dB
Crosstalk (1 kHz) ––––––––––––––––––––––––– ≥-90 dB
Tuner
Tuning range
FM ––––––––––––––––––––––––– 87.5 MHz–108 Mhz
MW –––––––––––––––––––––––– 531 kHz–1602 kHz
Stereo sensitivity ––––––––––––––––––––––––––– 41 dBf
DVD
Disc diameter –––––––––––––––––––––––– 12 cm / 8 cm
Video DAC ––––––––––––––––––––––––––––––– 10 bits
Signal system ––––––––––––––––––––––––– PAL / NTSC
Video format –––––––––––––––––––––––––––– 4:3 / 16:9
Laser
Laser type
DVD ––––––––––––––––––––––––––––––– InGaAIP
CD––––––––––––––––––––––––––––––––– AIGaAs
Wavelength
DVD ––––––––––––––––––––––––––––––– 660 nm
CD––––––––––––––––––––––––––––––––– 780 nm
Output power (out of objective)
DVD+RW writing –––––––––––––––––––– 20 mW
DVD reading –––––––––––––––––––––––– 0.8 mW
CD reading ––––––––––––––––––––––––– 0.3 mW
Beam divergence
DVD –––––––––––––––––––––––––––– 82 degrees
CD ––––––––––––––––––––––––––––– 54 degrees
Input connections
Analogue LINE IN 1, 2 ––––––––––––––– 900 mV / 47 kΩ
Analogue CAM 1 (front) ––––––––––––––– 2.2 V / 10 kΩ
Digital optical –––––––––––––––––––––––––––––– toslink
Digital coaxial ––––––––––––––––––––– 75 Ωacc. IEC958
Scart EXT 1, 2
TV antenna –––––––––––––––––––––––––––––––– 75 Ω
FM antenna –––––––––––––––––––––––––––––––– 75 Ω
MW antenna –––––––––––––––––––––––––––––– 300 Ω
S-Video CAM 1 (front) ––––––––––––––––––– 1V / 75 Ω
Video CAM 1 (CVBS, front) ––––––––––––––– 1V / 75 Ω
Digital CAM 2 (DV IN, front) ––––– acc. IEEE 1394 MPEG2
Output connections
Analogue LINE OUT –––––––––––––– 1.5 V / 2 kΩ/ 0 dB
Digital coaxial ––––––––––––––– 0.5 V / 75 Ωacc. IEC958
TV antenna –––––––––––––––––––––––––––––––– 75 Ω
Speakers ––––––––––––––––––––––––––––––––––– 4 Ω
Subwoofer –––––––––––––––––––––––––––––––––– 8 Ω
Headphone (3.5 mm, 8–600 Ω) –––– 2.8V EMF, Ri= 80 Ω
Loudspeakers
Front and rear speakers
System –––––––––––––––– 2 way shielded, Closed Box
Impedance –––––––––––––––––––––––––––––––– 4 Ω
Speaker drivers –––––– 3 x 2" woofers, 1 x 3/4" tweeter
Dimensions (w x h x d) –– 73 mm x 282 mm x 73 mm
Centre speaker
System –––––––––––––––– 2 way shielded, Closed Box
Impedance –––––––––––––––––––––––––––––––– 4 Ω
Speaker drivers –––––– 4 x 2" woofers, 1 x 3/4" tweeter
Dimensions (w x h x d) – 435 mm x 73.5 mm x 65 mm
Subwoofer
System ––––––––––––––––––––––––––––– Bass Reflex
Impedance –––––––––––––––––––––––––––––––– 8 Ω
Speaker driver –––––––––––––––––––––––– 4" woofer
Dimensions base (w x h) ––––––––– 30 mm x 240 mm
Dimensions tube (w x h) –––––––– 115 mm x 940 mm
Technical data
5
English
CAUTION
VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN.AVOID EXPOSURE TO BEAM.
Note:This warning is located inside the enclosure.

Introduction
Record your own DVDs and enjoy the digital surround
sound and some of the best features of home cinema
technology with your DVD recorder system.
This set complies with the radio interference
requirements of the European Community.
CAUTION
Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Supplied Accessories
Your DVD recorder system is delivered with
– 2 front, 1 centre and 2 rear speakers
– 2 subwoofers integrated in the speaker stands
– 7 speaker cables
– 1 SCART cable
– 1 cinch audio cable
– 1TV antenna cable
– 1 FM antenna cable
– 1 MW loop antenna
– 1 AC power cable
– 1 remote control with 2 AA batteries
– 1 blank Philips DVD+RW disc
Setup
Place the set on a flat, hard and stable surface.
Do not position the set on top of other equipment that
might heat it up (e.g. receiver or amplifier).
Allow at least 10 cm clearance from the rear and the
top of the set and 5 cm from the left and right to prevent
overheating.
Do not block the ventilation openings.
Do not expose the set to dripping or splashing.
Do not place any sources of danger (e. g. lighted candles,
objects filled with liquid) on the set.
Active mobile phones near the set may cause malfunctions.
Maintenance
Clean the set with a soft, slightly
dampened, lint-free cloth. Do not
use any cleaning agents as they
may have a corrosive effect.
Do not expose the set, batteries
or discs to humidity, rain, sand or
excessive heat (caused by heating
equipment or direct sunlight).
Always keep the tray of your DVD recorder system closed
to protect the lens from dust. Do not use any commonly
available lens cleaning discs, as they may damage the optical
unit of the set.
The lens may cloud over when the set is moved from cold
to warm surroundings. Playing or recording a disc is not
possible then. Leave the set in a warm environment until
the moisture evaporates.
Disc handling
DVD+Rs and DVD+RWs are very
delicate. Please take special care
when handling the discs.To take a
disc out of its box easily, press the
centre spindle while lifting it.After
use, always take the disc out of the
DVD recorder system and store it in the disc case.
Never attach a sticker to a disc. If you want to provide a
disc with an inscription use a soft felt-tipped pen and write
only on the printed side.
To clean a disc, wipe it in a straight
line from the centre towards the
edge using a soft, lint-free cloth.
Any cleaning agents may damage
the disc!
Environmental information
All redundant packing material has been omitted.We have
done our utmost to make the packaging easily separable into
three mono materials: cardboard (box), polystyrene foam
(buffer) and polyethylene (bags, protective foam sheet).
Your set consists of materials which can be recycled if
disassembled by a specialized company. Please observe the
local regulations regarding the disposal of packing materials,
exhausted batteries and old equipment.
General information
6
English
10 cm
10 cm
5 cm
5 cm

Which discs can be used?
There is a great number of disc types and you can use
many of them on your DVD recorder system. Some can be
used for playback only, others for playback and recording,
but there are a few types of discs which cannot be used
with this DVD recorder system.To determine which discs
you can use on this DVD recorder system, refer to the
logos shown below and look for these logos on your discs.
Discs for playback only
– DVD-Video
– DVD-R
plays only if it contains
DVD Video and if
finalised.
– DVD-RW
plays only if it contains
DVD Video and if
finalised.
– Video CD,
SuperVideo CD
– Audio CD
– Audio CDR,Audio CDRW
plays only if finalised.
– CDR, CDRW
plays only Audio CD
tracks and MP3 files
if finalised.
Discs for playback and recording
– DVD+R
can be recorded once and played
on standard DVD players and
DVD recorders, if finalised.
– DVD+RW
can be recorded, erased and
re-recorded many times and played on
DVD+RW compatible DVD players
and DVD recorders if finalised.
Discs unsuited for playback or recording
– DVD-RAM
– DVD-Audio
Region code
DVDs and DVD players are released for specific regions
around the world. DVDs must be labelled for ALL regions
or for region 2 in order to play them on this DVD recorder
system.You cannot play DVDs that are labelled for other
regions.
Trademark and license
information
ShowView is a registered
trademark of Gemstar
Development Corporation.
The ShowView system is manufactured under license from
Gemstar Development Corporation.
Manufactured under license from
Dolby Laboratories.“Dolby”,
“Pro Logic”, and the double-D symbol
are trademarks of Dolby Laboratories.
Manufactured under license from
DigitalTheater Systems, Inc. US Pat. No.
5,451,942, 5,956,674, 5,974,380, 5,978,762
and other world-wide patents issued
and pending.“DTS” and “DTS Digital Surround” are
registered trademarks of Digital Theater Systems, Inc.
Copyright 1996, 2000 Digital Theater Systems, Inc.
All Rights reserved.
See license, trademark and warning notice on the
bottom of the set.
General information
7
English

Inserting the batteries
1Open the battery compartment of the remote control and
insert 2 alkaline batteries, type AA (R06, UM-3).
2Close the battery compartment.
Do not use old and new or different types of batteries in
combination.
Remove batteries if they are empty or if the remote control
will not be used for a long time.
Batteries contain chemical substances, so they should
be disposed of properly.
Using the remote control
With this remote control you can control the
DVD recorder system as well as other Philips appliances
such as a PhilipsTV,VCR or CD player.
To control a Philips appliance, briefly press the
corresponding source key (TV, SAT, CAM 1/2, CD, CDR or
VCR) on the remote control. Some of the remote control
keys, e. g. 2, 0–9, CH+, CH–,4,¢,9,2;can be used
to control the appliance then.To control the DVD recorder
system with these keys, pressTUNER or DVD/MON.
To select a source on the DVD recorder system, keep the
source key (TV, SAT, CAM 1/2, CD, CDR or VCR) on the
remote control pressed for 1 second.
To select CAM 2 (or TAPE, GAME), first select CAM 1 (or
CDR,VCR), then keep the corresponding key pressed for
1 second.
To control the DVD recorder system, please point the
remote control at the DVD recorder system and not at
theTV.
Remote Control
8
English
TV
CDR/TAPE
CAM 1/2 CD
TUNER SAT
MENU
REC MODE DISC DISPLAY
CLEAR RETURNEDIT
PLAY MODE
TREBLE
TIMER
LOUDNESS
VCR/GAME
DVD/MON
BASS
SUBWOOFER
REAR
NIGHT
VOICE
TV VOL
REC/OTR
CHVOL MUTE
SELECT
SURR.
+
-
AUDIODISC
É
É
É
É
0
OK
H
§
T/C
SURR.
2;
∞9
13
2
46
5
79
8
SYSTEM
2
1
2
3
4
7
8
9
!
%
(
)
^
£
≤
§
•
ª
&
*
¡
™
∞
≥
5
6
$
@
0
#
º

Remote control keys
12
switches the DVD recorder system and a Philips appliance
on or to standby
2REC/OTR
starts recording theTV channel or video source selected
on the DVD recorder system
3DVD/MON
selects the disc in the tray or the TV channel selected on
the DVD recorder system
TV
selects theTV
TUNER
selects the radio tuner, selects the waveband and switches
between FM mono and FM stereo
SAT
selects a connected satellite receiver
CAM 1/2
selects the camcorder inputs on the front
CD
selects a connected CD player
CDR/TAPE
selects a connected CD recorder, tape deck or similar
VCR/GAME
selects a connectedVCR or game console
40–9 to key in numbers 0–9
5DISC MENU
enters the disc menu
6SYSTEM MENU
enters the system menu of the DVD recorder system
7AUDIO MENU / SELECT
enters the audio menu of the DVD recorder system and
selects an option in the system menu
8OK
confirms menu options
9Arrow keys 1,3,2,4
to move in a menu
0VOL +,VOL –
increases/decreases the volume of the DVD recorder
system
!H
mutes the sound of the DVD recorder system
@CH+, CH–
selects aTV channel on the DVD recorder system and
selects a preset radio station
#4/ –TVVOL
skips to the beginning of the current or previous
chapter/title/track of the inserted disc, searches backwards,
tunes to a radio station with a lower frequency and
decreases the volume of a PhilipsTV
$¢/TVVOL+
skips to the beginning of the next chapter/title/track of the
inserted disc, searches forwards,
tunes to a radio station with a higher frequency and
increases the volume of a PhilipsTV
%2;
starts/pauses playback and closes the disc tray
^9
stops playback or recording
&REC MODE
selects a recording mode: HQ, SP, SP+, LP, EP or EP+
*PLAY MODE
selects different playback modes like REPEAT or SHUFFLE
(DISPLAY
selects various display information
)T/C / DISC
switches between title, track and chapter and
changes discs on a Philips CD changer
¡TIMER
enters the timer recording menu
™EDIT
enters the menu Favorite Scene Selection
£SURR. / RETURN
selects the different surround modes and
returns to the previous menu on a (Super) Video CD
≤CLEAR
clears an entry (eg. timer preset)
∞SUBWOOFER (in combination withVOL+or VOL−)
adjusts the subwoofer volume
§LOUDNESS
switches loudness on and off
≥REAR (in combination withVOL+or VOL−)
adjusts the volume of the rear speakers
•VOICE / NIGHT
switches ClearVoice or Night mode on or off
ªTREBLE (in combination withVOL+or VOL−)
adjusts the treble
ºBASS (in combination withVOL+or VOL−)
adjusts the bass
Remote Control
9
English

Controls on the front
12STANDBY·ON
switches the set on or to standby
2SOURCE
selects a source
34SEARCH
skips to the beginning of the current or previous
chapter/title/track of the inserted disc, searches backwards
4SEARCH ¢
skips to the beginning of the next chapter/title/track
of the inserted disc, searches forwards
5STOP 9
stops playback or recording
6PLAY/PAUSE 2;
starts/pauses playback
7display/DVD recorder drawer
8OPEN/CLOSE /
opens/closes the DVD recorder drawer
9SURR.
selects the different surround modes
0INSTANT – RECORD (status light)
indicates if immediate recording is possible
!RECORD
starts recording aTV channel or an external
video source selected on the DVD recorder system
(the key is illuminated while recording is in progress)
@VOLUME
adjusts the volume
Connections on the front
#PHONES
3.5 mm headphone socket
$DV IN / CAM 2
connect to the i.Link output of your DigitalVideo (DV) or
Digital 8 camcorder
%S-VIDEO / CAM 1
connect to the S-video output of your Hi-8 or S-VHS
camcorder
^VIDEO / CAM 1
connect to the video (CVBS) output of your camcorder
&AUDIO LEFT/RIGHT / CAM 1
connect to the audio output of your camcorder
Controls and connections
10
English
123456 7 0! @ #
%& ^
89
$

Connections on the rear
1connect to the supplied speakers
2RADIO / MW
connect to the MW antenna
3RADIO / FM
connect to the FM antenna
4MAINS ~
After all other connections have been made,
connect the mains lead to the wall socket.
5TV ANTENNA / IN
connect to theTV antenna
6TV ANTENNA / TV OUT
connect to theTV antenna input of yourTV
7EXT 2 / AUX I/O
connect to the SCART socket of an external video
appliance
8EXT 1 /TOTV I/O
connect to the SCART socket of the TV
9LINE IN 1 L/R
connect to the analogue audio output of an external
appliance (e. g. tape deck, CD changer, …)
0LINE IN 2 L/R
connect to the analogue audio output of an external
appliance (e. g. tape deck, CD changer, …)
!LINE OUT L/R
connect to the analogue audio input of an external
appliance (e. g. tape deck, …)
@DIGITAL IN
connect to the digital coaxial output of a digital appliance
#OPTICAL IN
connect to the digital optical output of a digital appliance
$DIGITAL OUT
connect to the digital coaxial input of a digital appliance
Before starting with the connections, make sure all
appliances that you want to connect as well as the
DVD recorder system are disconnected from the
power sockets.
Controls and connections
11
English
TV ANTENNA
IN
TV OUT
EXT 2
EXT 1
MW FM
AUX I/0
TO TV I/0
L
R
L
R
DIGITAL OUT
DIGITAL IN
OPTICAL IN
LINE IN 1 LINE IN 2 LINE OUT
MAINS ~
RADIO
CENT.
4 Ω
SURR
LEFT
4 Ω
SURR
RIGHT
4 Ω
SUB
LEFT
8 Ω
FRONT
LEFT
4 Ω
FRONT
RIGHT
4 Ω
SUB
RIGHT
8 Ω
2 3 4
5 76 8 @ # $9 0 !
1

Speaker setup
1First, assemble the speakers as described in the supplied
”Quick use guide”.You can place the subwoofers either in
the front or in the rear.
2Place the front left and right speakers at equal distances
from yourTV.The distance between the listener´s position
and the front speakers should be approximately equal to
the distance between the two front speakers.
3Place the centre speaker above or below theTV set.
4Place the rear speakers to the left and right of your
preferred listening position.
Notes:
Keep the speakers away from the corners of the room.
Position the speakers at ear level.
Connecting the speakers
Connect the supplied speakers using the supplied speaker
cables. Match the colours of the speaker sockets and the
speaker cables:
Speaker ++−−
Front Left white black
Front Right red black
Centre green black
Subwoofer Left violet black
Subwoofer Right violet black
Rear Left blue black
Rear Right grey black
Note: If you placed the subwoofers in the rear, the colours of
the cables will no longer match the speaker sockets on the
subwoofers.
We recommend connecting all speakers. At least the front
speakers and the subwoofers must be connected.
●Press down the clip of the speaker and fully insert the
stripped portion of the speaker cable into the socket, then
release the clip.
Speaker setup/Connecting …
12
English
front R,
subwoofer R
front L,
subwoofer L
rear L rear R
centre

Connecting the tuner antennas
MW antenna
●Assemble the supplied MW loop antenna as shown below
and connect it to RADIO MW.
Notes:
After finishing the hookup and the initial setup, move the
MW antenna in various directions to achieve best reception.
Keep the antenna as far away as possible from the TV,VCR
or other electronic appliances.
For better reception connect an outdoor antenna or a cable
TV system.
The supplied antenna is for indoor use only.
FM antenna
●Connect the FM antenna socket of an outdoor FM antenna
or that of your cable TV system to RADIO FM on the DVD
recorder system with the supplied FM antenna cable.
Connecting theTV antenna
1Disconnect the antenna cable from theTV´s antenna input
and connect it toTV ANTENNA IN on the DVD recorder
system.
2ConnectTV ANTENNATV OUT on the DVD recorder
system to theTV´s antenna input with the supplied antenna
cable.
If you connect an appliance or change its connection after
the initial installation, you need to “install” it on the DVD
recorder system, i. e. you have to tell the DVD recorder
system to which socket the appliance is connected.
Otherwise the appliance will not be available on the DVD
recorder system. Please see “When adding appliances or
changing the connections of appliances”.This is not
necessary for appliances connected to CAM 1 and CAM 2.
Connecting theTV
Consult the user´s manuals of yourTV on which SCART
sockets are available and how to connect them to other
video appliances.
If several SCART sockets are available on your TV, select
one that is suited for RGB input to achieve the best picture
quality.
If your PhilipsTV supports EasyLink, please select the
SCART socket number 2 on the TV (EXT2, EXTERNAL 2
or similar) which supports EasyLink.
Connect theTV directly to the DVD recorder system
without aVCR or any other appliance in between.
Otherwise, not all functions of the DVD recorder system
may be available.
1Connect the SCART socket of the TV
(EUROCONNECTOR, EURO-AV or similar) to
EXT 1TOTV I/O on the DVD recorder system with the
supplied SCART cable.
2If you have a digitalTV with a digital audio output, connect
either
– its digital coaxial output to DIGITAL IN on the DVD
recorder system with a digital cinch cable or
– its digital optical output to OPTICAL IN on the DVD
recorder system with a digital optical cable.
Connecting …
13
English
MW
RADIO
TV ANTENNA
IN
TV OUT
EXT 2
EXT 1
MW FM
AUX I/0
TO TV I/0
L
R
L
R
DIGITALOUT
DIGITALIN
OPTICAL IN
LINE IN 1 LINEIN 2 LINE OUT
MAINS ~
RADIO
EXT IN
ANTENNA IN
TV
OPTICAL
OUT
TV ANTENNA
IN
TV OUT
EXT 2
EXT 1
MW FM
AUX I/0
TO TV I/0
L
R
L
R
DIGITALOUT
DIGITALIN
OPTICAL IN
LINE IN 1 LINEIN 2 LINE OUT
MAINS ~
RADIO
EXT IN
ANTENNA IN
TV
OPTICAL
OUT
to antenna, cable TV or VCR

Connecting additional video
appliances
You can connect several video appliances with a SCART
socket to EXT2 AUX I/O by connecting them in a “chain”:
In the illustration below, a satellite receiver is connected to
aVCR and the VCR to the DVD recorder system.
Please keep in mind that the appliance closest to the
DVD recorder system will provide the input signal if several
appliances in the chain are switched on.Therefore:When
selecting a video appliance connected to EXT2 AUX I/O,
make sure that all other appliances connected to
EXT2 AUX I/O are switched off or to standby.
Consult the user´s manuals of the video appliances you
wish to connect on which SCART sockets are available and
how to connect them to other video appliances.
1Connect the SCART socket of a video appliance to
EXT2 AUX I/O on the DVD recorder system with a
SCART cable. If the appliance has several SCART sockets,
use the one labelledTOTV or similar.
Note: Use RGB capable SCART cables only. Some other SCART
cables are only partially wired, resulting in a moderate picture
quality and less functionality of the SCART connection.
2Connect another video appliance to the free SCART
socket on the video appliance which is already connected
to the DVD recorder system.
3If a digital video appliance (e. g. satellite receiver or game
console) supports digital surround sound, connect either
– the digital coaxial output of the appliance to DIGITAL IN
on the DVD recorder system with a digital cinch cable,
– the digital optical output of the appliance to
OPTICAL IN on the DVD recorder system with a digital
optical cable.
Connecting additional audio
appliances
Please consult the user´s manual of your audio appliances
on which connections are possible.
Analogue connections
1Connect the left and right analogue output sockets of
your tape deck, CD player or similar to LINE IN 1 L/R or
LINE IN 2 L/R on the DVD recorder system with an
audio cinch cable.
Note:You cannot connect a turntable to LINE IN 1 or 2.
2Connect the left and right analogue input sockets of a
tape deck or similar recording appliance to LINE OUT L/R
on the DVD recorder system with an audio cinch cable.
Digital connections
1Connect either
– the digital coaxial output socket of your CD recorder,
CD player or similar to DIGITAL IN on the DVD
recorder system with a digital cinch cable or
– the digital optical output socket of your CD recorder,
CD player or CD changer to OPTICAL IN on the DVD
recorder system with a digital optical cable.
2Connect the digital coaxial input socket of your CD recorder
or similar digital recording appliance to DIGITAL OUT on
the DVD recorder system with a digital cinch cable.
Note: DIGITAL OUT provides digital 2-channel stereo sound.
The DVD recorder system converts digital multichannel sound
into 2-channel stereo sound without loss of relevant sound
information.
Connecting …
14
English
TV ANTENNA
IN
TV OUT
EXT 2
EXT 1
MW FM
AUX I/0
TO TV I/0
L
R
L
R
DIGITALOUT
DIGITALIN
OPTICAL IN
LINE IN 1 LINEIN 2 LINE OUT
MAINS ~
RADIO
EXT. IN
TO TV
TO TV
OPTICAL
OUT
TV OUT
ANTENNA
EXT IN
ANTENNA IN
VCR
SAT Receiver
TV
TV ANTENNA
IN
TV OUT
EXT 2
EXT 1
MW FM
AUX I/0
TO TV I/0
L
R
L
R
DIGITALOUT
DIGITALIN
OPTICAL IN
LINE IN 1 LINEIN 2 LINE OUT
MAINS ~
RADIO
CD player
LL
R
DIGITAL OUT
Tape deck
OUT IN
R

Connecting a camcorder to
CAM 1 or CAM 2
You can connect 2 camcorders to the connections CAM 1
and CAM 2.The picture quality depends on the type of
connection between the camcorder and the DVD recorder
system:
– good quality: CompositeVideo (Video CVBS)
– better quality: S-Video
– best quality: i.Link (IEEE 1394, Fire Wire)
Select the best connection available. Only one video
connection between the DVD recorder system and the
camcorder is needed.
1Open the flap on the front of the DVD recorder system.
2Connect the camcorder to CAM 1 or CAM 2 following the
instructions in the user´s manual of your camcorder.
Note: If the camcorder connected to CAM 1 has mono
sound only, connect the audio output of the camcorder to
CAM 1 AUDIO RIGHT on the DVD recorder system.
Connecting headphones
●Connect the headphones with an 3.5 mm plug to PHONES
on the DVD recorder system.
➜The speakers are switched off automatically. Sound will
be reproduced through the headphones only.
Note:With connected headphones, no surround sound is
available. If you press SURROUND,DISCONNECT
HEADPHONES will be scrolled on the display of the DVD
recorder system.
Mains
The type plate is located on the rear of the set.
1Check whether the mains voltage as shown on the type
plate corresponds to your local mains voltage. If it does not,
consult your dealer or service organisation.
2Make sure yourTV is switched on before connecting the
DVD recorder system to the mains supply for the first time.
3Make sure all connections have been made before
connecting the DVD recorder system to the mains
supply.
4Connect the supplied mains cable to AC MAINS ~ and to
the wall socket.
When the set is switched to standby, it is still consuming
some power. To disconnect the set from the mains
completely, remove the mains plug from the wall
socket.
To avoid overheating of the set a safety circuit has
been built in.Therefore your set may disconnect
under extreme conditions. If this happens, switch the
set off and let it cool down before reusing it.
When you connect the DVD recorder system to the mains
supply for the first time, you need to perform some basic
settings. See “Initial installation”.
Connecting …
15
English
S-Video Video, CVBS,
CompositeVideo
i.Link
(IEEE 1394, Firewire,…)

During the initial installation, you will perform some basic
settings of the DVD recorder system.You can change all
settings of the initial installation later on.To change these
settings please see the chapters of “System settings” and
tPicture and uLanguage in “User preferences”.
Basic settings
Please observe the screen of yourTV and the display of the
DVD recorder system.
1Switch on yourTV.
2Connect the supplied mains cable to AC MAINS ~ and to
the wall socket. If the DVD recorder system is in demo
mode, press 2to cancel the demo mode.
➜IS TV ON?is displayed on the DVD recorder system.
3If necessary set the TV to the correct audio/video channel
for the DVD recorder system. Such channels may be called
AUX or AUXILIARY IN,AUDIO/VIDEO or A/V IN, EXT1,
EXT2 or EXTERNAL IN, etc.These channels are often near
channel 00.
Note: If your TV supports EasyLink, the TV and the DVD
recorder system exchange information via the SCART cable.
In this case, EasyLink loading data fromTV, please
wait will appear on the TV. Some of the following settings will
be done automatically then.
4➜The menu Menu Language appears on theTV screen.
Press 3or 4to select the language in which the display
messages should appear on theTV screen.Then press OK.
5➜The menu Audio language appears.
Press 3or 4to select the language in which DVDs should
preferably be played, if the language is available on the disc.
Then press OK.
6➜The menu Subtitle Language appears.
Press 3or 4to select the language in which subtitles
should preferably be displayed, if subtitles in the language
are available on the disc.Then press OK.
Note: Some DVDs may override your audio and subtitle
language selection. In this case, you have to select the audio
and subtitle language in the DVDs Disc Menu.
7➜The menu TV Shape appears.
Press 3or 4to select the screen format.This setting will
have an effect only with DVDs supporting different screen
formats.
➜4:3 letterbox: for a wide-screen picture (cinema
format) on a conventional 4:3TV set with black borders
at the top and bottom of the screen.
➜4:3 panscan: for a full-height picture with cropped
edges.
➜16:9: for a wide-screenTV set.
Then press OK.
8➜The menu Country appears.
Press 3or 4to select the country where the
DVD recorder system is used. If your country does not
appear, select Other.Then press OK.
9➜If you have connected the antenna - press OK
appears.
If you connected the DVD recorder system to aTV antenna
or a cableTV system, press OK.
If not, connect the antenna as described in “Connecting
theTV antenna”, then press OK.
➜Searching for TV channels appears and the
automatic search forTV channels starts.This may take
several minutes.As soon as the search is complete,
Autom. search complete appears.
10 ➜Time,Year,Month and Date appear.
If the settings are correct continue with step 13, else press 4
repeatedly to select either Time,Year,Month or Date.
11 Press 1or 2or 0–9 repeatedly to set the correct value.
12 If necessary, repeat steps 10 and 11 until all settings of the
time and date are correct.
13 Press OK.
➜CONTINUE WITH SPECIAL AUDIO SETTINGS is
scrolled on the DVD recorder system.
14 Continue with “Advanced settings”.
Initial installation
16
English
TV
CDR/TAPE
CAM 1/2 CD
TUNER SAT
MENU
VCR/GAME
DVD/MON
REC/OTR
SELECT
AUDIODISC
É
É
0
OK
H
13
2
46
5
79
8
SYSTEM
2
É
É

Advanced settings
You will be asked
– about the distances between the speakers and your
preferred listening position and
– to which input sockets on the DVD recorder system you
connected other appliances.
If you want to skip the advanced settings and to use
standard settings for the speaker distances and the
connections (see “Quick use guide”):
Press 4to select NO, and continue with step 11 below.
If you want to continue with the advanced settings:
Press OK.
➜SPEAKER DISTANCES is scrolled.
1➜FRONT and 3,0Mare displayed.
Press 3or 4repeatedly to set the distance of your
preferred listening position to the front speakers.
Then press OK to confirm.
2➜CENTER and 3,0Mare displayed.
Repeat step 1 for the centre speaker.
3➜REAR and 1,5Mare displayed.
Repeat step 1 for the rear speakers.
➜SOURCE SETUP is scrolled.
4➜DIGITAL AUDIO FROM TV?is scrolled.
Press 4repeatedly to select
➜NO if there is no digital audio connection between theTV
and the DVD recorder system,
➜DIG if you connected theTV´s digital coaxial output to
DIGITAL IN on the DVD recorder system,
➜OPT if you connected theTV´s digital optical output to
OPTICAL IN on the DVD recorder system.
Press OK to confirm.
5➜VCR CONNECTED?is scrolled and YES is displayed.
If you did not connect a VCR to the DVD recorder
system:
Press 4to select NO, then press OK.
If you connected a VCR:
Press OK.
➜WHICH INPUT?is scrolled.
Press 4repeatedly to select
➜EXT2 if you connected theVCR to EXT 2 AUX I/O or
➜EXT1 if you connected theVCR to EXT 1TOTV I/O on
the DVD recorder system.
Press OK to confirm.
➜DIGITAL AUDIO?is scrolled.
Press 4repeatedly to select
➜NO if there is no digital audio connection between the
VCR and the DVD recorder system,
➜DIG if you connected the digital coaxial output of the
VCR to DIGITAL IN on the DVD recorder system,
➜OPT if you connected the digital optical output of the
VCR to OPTICAL IN on the DVD recorder system.
Press OK to confirm.
6➜SAT CONNECTED?is scrolled and YES is displayed.
Repeat step 5 for a satellite receiver.
7➜GAME CONNECTED?is scrolled and YES is displayed.
Repeat step 5 for a game console.
8➜CD CONNECTED?is scrolled and YES is displayed.
If you did not connect a CD player to the DVD
recorder system:
Press 4to select NO, then press OK.
If you connected a CD player:
Press OK.
➜WHICH INPUT?is scrolled.
Press 4repeatedly to select
➜LIN1 or LIN2 if you connected the analogue audio
output of the CD player to LINE IN 1 or LINE IN 2 on
the DVD recorder system,
➜DIG if you connected the digital coaxial output of the
CD player to DIGITAL IN on the DVD recorder system,
➜OPT if you connected the digital optical output of the
CD player to OPTICAL IN on the DVD recorder
system.
Press OK to confirm.
9➜CDR CONNECTED?is scrolled and YES is displayed.
Repeat step 8 for a CD recorder or similar.
10 ➜TAPE CONNECTED?is scrolled and YES is displayed.
Repeat step 8 for a tape deck or similar.
➜SOURCE SETUP COMPLETE is scrolled.
11 Press OK.
➜AUTOINSTALL is displayed.The DVD recorder system
searches for available radio stations and stores them in its
memory.
➜After the search INSTALLATION COMPLETE is
scrolled and a radio station is played.The DVD recorder
system is ready to play.
Initial installation
17
English

When adding appliances or
changing the connections of
appliances
If you have connected additional appliances or changed the
connections after the initial installation, you need to tell the
DVD recorder system to which socket on the rear of the
DVD recorder system the appliance is connected.
After changing the connection of theTV e
1Press AUDIO MENU to enter the audio menu.
2Press 4repeatedly to select INPUTS, then press 2.
3Turn SOURCE on the DVD recorder system or keep TV on
the remote control pressed for 1 second.
➜eand AUDIO -> are displayed.
4Press 4repeatedly to select
➜EXT1 if you connected theTV to EXT 1 only
(no digital audio connection between theTV and the
DVD recorder system),
➜DIG if you connected the digital coaxial output of theTV
to DIGITAL IN,
➜OPT if you connected the digital optical output of theTV
to OPTICAL IN on the DVD recorder system.
5Press OK to store the setting.
6Press AUDIO MENU to exit the audio menu.
After changing the connections of theVCR j,
satellite receiver ior game console r
1Press AUDIO MENU to enter the audio menu.
2Press 4repeatedly to select INPUTS, then press 2.
3Turn SOURCE on the DVD recorder system or use the
source keys on the remote control to select theVCR,
satellite receiver or game console.
➜AVAILABLE and YES or NO are displayed.
4If the appliance is not connected to the
DVD recorder system:
Press 4repeatedly to select NO, then press OK.
➜STORED is displayed.
If the appliance is connected to the DVD recorder
system:
Press 4repeatedly to select YES, then press OK.
➜VIDEO -> is displayed.
Press 4repeatedly to select
➜EXT1 if you connected the appliance to EXT 1,
➜EXT2 if you connected the appliance to EXT 2,
➜NONE if you did not connect the appliance to EXT 1 or
EXT 2 on the DVD recorder system.
Press OK to confirm.
➜AUDIO -> is displayed.
Press 4repeatedly to select either
➜EXT1 or EXT2 if you connected the appliance to EXT 1
or EXT 2 only (no digital audio connection between the
appliance and the DVD recorder system),
➜LIN1 or LIN2 if you connected the audio output of
the appliance to LINE IN 1 or LINE IN 2 (available only if
you selected VIDEO ->NONE),
➜DIG if you connected the digital coaxial output of the
appliance to DIGITAL IN,
➜OPT if you connected the digital optical output of the
appliance to OPTICAL IN on the DVD recorder system.
Press OK to store the settings.
➜STORED is displayed.
5Press AUDIO MENU to exit the audio menu.
System settings
18
English
TV
CDR/TAPE
CAM 1/2 CD
TUNER SAT
MENU
VCR/GAME
DVD/MON
REC/OTR
SELECT
AUDIODISC
É
É
0
OK
H
13
2
46
5
79
8
SYSTEM
2
É
É

After changing the connections of the
CD recorder p, CD player qor tape deck k
1Press AUDIO MENU to enter the audio menu.
2Press 4repeatedly to select INPUTS, then press 2.
3Turn SOURCE on the DVD recorder system or use
the source keys on the remote control to select either
the CD recorder, CD player or tape deck.
➜AVAILABLE and YES or NO are displayed.
4If the appliance is not connected to the
DVD recorder system:
Press 4repeatedly to select NO, then press OK.
➜STORED is displayed.
If the appliance is connected to the DVD recorder
system:
Press 4repeatedly to select YES, then press OK.
➜AUDIO -> is displayed.
Press 4repeatedly to select
➜LIN1 or LIN2 if you connected the analogue audio
output of the appliance to LINE IN 1 or LINE IN 2,
➜DIG if you connected the digital coaxial output of the
appliance to DIGITAL IN,
➜OPT if you connected the digital optical output of the
appliance to OPTICAL IN on the DVD recorder system.
Press OK to store the settings.
➜STORED is displayed.
5Press AUDIO MENU to exit the audio menu.
When changing the speaker
setup
If you have connected, disconnected or moved the speakers
after the initial installation, you need to change the speaker
settings.
Setting which speakers are connected
1Press AUDIO MENU to enter the audio menu.
2Press 4repeatedly to select LS SETUP, then press 2.
3Press 4repeatedly to select
➜CNTR LS: the centre speaker or
➜REAR LS: the rear speakers.
4Then press 2.
5Press 4repeatedly to select
➜YES if the selected speaker type is connected or
➜NO if the selected speaker type is not connected.
6Press OK to store the setting or 1to exit without storing.
00If necessary, repeat steps 3–6 for the other speaker type.
7Press AUDIO MENU to exit the audio menu.
Setting the distance of your listening position to
the speakers
1Press AUDIO MENU to enter the audio menu.
2Press 4repeatedly to select LS DIST, then press 2.
3Press 4repeatedly to select
➜DIST FRNT: distance to the front speakers,
➜DIST CNTR: distance to the centre speaker or
➜DIST REAR: distance to the rear speakers.
4Then press 2.
5Press 3or 4repeatedly to set the distance of your
listening position to the speakers (from 1 to 10 meters).
6Press OK to store the setting or 1to exit without storing.
00To set the distance to another speaker type, repeat steps
3–6.
7Press AUDIO MENU to exit the audio menu.
System settings
19
English

SearchingTV channels
1Switch yourTV set on. If necessary set the TV to the
correct audio/video channel for the DVD recorder system.
Such channels may be called AUX or AUXILIARY IN,
AUDIO/VIDEO or A/V IN, EXT1, EXT2 or EXTERNAL IN,
etc.These channels are often near channel 00.
2Press SYSTEM MENU.
3Press 1repeatedly to select A.
4Press 4repeatedly to select yInstallation, then press 2.
5Press 4repeatedly to select either
➜Autom. Search: to search forTV channels automatically,
➜Manual search: to add additional or missing TV channels
manually.
Note: If your TV supports EasyLink, please add new TV channels
on your TV first.Then select Autom. Search to transfer the
changes to the DVD recorder system. Some of the menu options
below will not be available with EasyLink.
6Press 2to enter the selected menu.
Autom. Search
Select Autom. Search if newTV channels are available
with your antenna or cable TV system. All previously stored
TV channels will be overwritten.
1Press 2to start the automatic search.
➜Searching for TV channels and xx Channels
found appear, where xx indicates the number of
TV channels found.
2After the search is complete, press SYSTEM MENU to exit.
Note: If your TV supports EasyLink the TV channels will be
stored in the same order as on your TV.
Manual search
If not all available TV channels have been found during the
initial installation, you can search for the missingTV channels
manually.
1➜Channel/freq. is highlighted.
Press 2repeatedly to select
➜CH or S-CH if you want to enter the channel number,
➜Freq. if you want to enter the frequency of theTV
channel.
2Press 4to select Entry/search.
3Press 0–9 repeatedly to enter the channel number or
the frequency of the desiredTV channel.
00If you do not know the channel number or frequency,
press 2to start automatic search. Repeat this step until
the desiredTV channel is found.
4Press 4to select Programme number.
5Press 0–9 or 3or 4repeatedly to enter the programme
number where to store theTV channel.
Note: If Programme number already used appears on
the TV screen, select another programme number. Otherwise
the TV channel with the same programme number will be
deleted.
6Press OK to store the newTV channel or SYSTEM MENU
to exit without storing the changes.
7Press SYSTEM MENU to exit the system menu.
System settings
20
English
TV
CDR/TAPE
CAM 1/2 CD
TUNER SAT
MENU
VCR/GAME
DVD/MON
REC/OTR
SELECT
AUDIODISC
É
É
0
OK
H
13
2
46
5
79
8
SYSTEM
2
É
É