Philips MCD735 series User manual

MCD 735
Quick Start Guide
What’s in the Box?
You should find these items upon opening the box.
2
User Manual
1
Quick Start Guide
Quick start guide
User manual
Subwoofer cable
AC power cord
FM and AM antennas Control Cable
A/V cord (R/W/Y)
Remote control with two
AAA batteries
Remote control with two
AAA batteries
BAND BAND
MCD735 QUG_Eng 2006.7.20, 15:101

Tips
–See the User Manual for other TV
connection options.
–For connecting to a Progressive Scan
TV, refer to the user manual for proper
connections and detailed setup.
1
2
4
3
1
5
4
3
2
5
Setting up the TV
1
2
Press SOURCE (DISC on the remote) to select disc source.
Turn on the TV and set it to the correctVideo In channel.
5
Connect the speaker and subwoofer cables.
Connect the AM and FM antennas.
Connect the control cable.
Connect the A/V cord to a TV.
Connect the power cords of the system and TV.
Front Speaker
(right)
Center
Speaker
RearSpeaker
(right)
Rear Speaker
(left)
Front Speaker
(left)
Subwoofer
AC power
AC power
FM Antenna AM Antenna
MCD735 QUG_Eng 2006.7.20, 15:102

Setting the clock
1
2
3
4
In standby mode, press and hold CLOCK on the remote.
When the hour digits flash, turn VOLUME-/+ on the system or press VOLUME+/- on the
remote to set the hours.
Press CLOCK again and the minute digits flash.Then turn VOLUME-/+ on the system or
press VOLUME+/- on the remote to set the minutes.
Press CLOCK again to confirm the time setting.
Setting DVD menu options
IMPORTANT!
If the progressive scan feature is activated but the connected TV does not support
progressive signals or the cables are not connected accordingly, see the user
manual for proper progressive scan setup or deactivate the progressive scan
feature as below:
1) Turn off your TV progressive scan mode or turn on to interlaced mode.
2) Press SYSTEM on the remote to exit the system menu and then DISC and “1”
to exit progressive scan.
Tip
See chapters "Preparations" and "System Menu Options" in the User
Manual for detailed descriptions.
DIVX(R) VOD
IMPORTANT!
– To set clock in the Eco Power mode, press and hold STANDBY-ON/ECO POWER
2 on the set
for 3 seconds or more to switch to normal standby mode first before proceeding with the
procedures below.
MCD735 QUG_Eng 2006.7.20, 15:103

1
2
3
Press OPEN •CLOSE (çon the remote) to open the disc tray and load in a disc, then
press the same button again to close the disc tray.
➜Make sure the label side of the disc is facing up.
Playback will start automatically. If not pressÉÅ.
To stop playback, press PRESET-/9(9on the remote).
Playing a disc
Programming and tuning to radio stations
1
2
3
Press SOURCE (TUNER on the remote) to select tuner source.
Press PROG on the remote for more than two seconds to program all available stations in
order of waveband.
Press PRESET+/- (CH +/- (¡/ ™)on the remote) until the desired preset station is
displayed.
Tip
Detailed playback features and
additional functions are described in the
accompany owner's manual.
PDCC-JS/JW-0627
2005 CKoninklijie Philips Electronics
N.V. All rights reserved.
http://www.philips.com
Notes for remote control:
– First, select the source you wish to control by
pressing one of the source select keys on the remote
control (DISC orTUNER, for example).
–Then select the desired function (
2; , í , ë for
example).
MCD735 QUG_Eng 2006.7.20, 15:104