5
190P6&170P6 LCD
Go to cover page
Technical Data(For 170P6)
"
"
"
"
1.General
1.1.1Product description
170P6 isthe 6th generation of Hudson 17 TFT Flat Panel Display
Monitor.The monitor featuredwith both DVI-Dandanalog signal
input interface,andmodularizedasadisplayunit with embedded
universal AC power suppliesinsidemonitor main body. The power
button anddisplaycontrol buttons(tact switch type) are on the front
ofthe monitor.The monitor shall support an internal scaler to
automaticallyenable the monitor to displaylower resolution video
modesinto 1280x1024 full screen display. The image can be
adjustedthrough OSDcontrolboard. Theseadjustmentscan be
storedonaboardmemoryincluding 34 pre-set modesand16
factorypre-set modes.
1.1.2 Destination:AP, CN, EE, GB, LA, ME, SH, WE
1.2. Basic data
1.2.1LCD panel
Type NR. : LM170E01-A6K3/A6K4 (LPL)
Number ofPixels. : 1280(H)x1024 (V)
Physical Size. : 358.5(w)*296.5(h)*17.0(d)mm
Pixel Pitch.:0.264(per one triad)x0.264mm
Color pixel arrangement.:RGBvertical stripes
Support Color.:16.2M colors(RGB8bitsdata)
DisplayMode.:NormallyWhite
Backlight.:CCFLedge light system
Active area.(WXH).:337.92 x 270.336mm (17 diagonal)
Viewing Angle.:Vertical 140degree,Horizontal
140degree (CR=10)
Contrastratio.:500:1
White luminance.:250nits(Typ)
1.2.2. Power supply
Main Voltage:AC90-135 Vrms and170-264Vrms, 50/60±2Hz
Power consumption:55wattsmax(full loading,with 4X USB
deviceson downstreamports, each device consumes0.5 Amp)
Operating <35W(typical value;no device loading on USB
downstreamport(s)) standby<1W.
DCpower switch off < 1W(no device loading on USB
downstreamport(s))
Power cordlength:1.5M
Power cordtype:3leadwith earth plug
Power indicator:LED(ON: green,S
tandby: amber)
Auto power saving:EPA, Nutek, VESA, DPMS,
STATUS H-
sync
V-
sync Video Powe
rLED
OnOnOnActive <55
W
Green /With Audio
andfull USB
loading
OnOnOnActive <35
W
Green /Without
Audio andUSB
loading
Stand-by Off OnBlanked<1WAmber LED
SuspendOnOff Blanked<1WAmber LED
Off Off Off Blanked<1WAmber LED
DCPower
off N/A <1WLEDOff
Note :
A. To achieve under 1 Watt power saving,makesure there isno
device loadon USB downstreamport(s).
B. To achieve under 1 Watt power saving when Stand-Alone
Audio feature isselectedOnand systemisin Sleep Mode,
followbelowtwoconditions:
1.Volumehasto beadjustedto 0%prior to measurement.
2.Makesure there isno device loadon USB downstreamport(s).
1.2.3.Horizontal scan:30-83KHz
1.2.4.Vertical scan:56-76 Hz
1.2.5. Inputsignals
The inputsignalscan be appliedin twodifferent modes:
1). VESA Analog
The video inputconsistsofred, green,andbluesignals. The video
signalsare analog levels, where 0Vcorresponds to blackand700mV
isthe maximum signal amplitude.Inputimpedance ofvideo pinsis
75ohm+/-1%.
The capabilityof sync signal inputsshall includeseparate sync,
composite sync andsync on green.inputimpedance:2k2ohms
The signalsare definedasfollow:
Separate sync TTLlevel,Positive/Negative
Composite sync TTLlevel,Positive/Negative
Sync on green H-sync TTLlevel,Positive/Negative
2).Intel DVI Digital
Inputsignal:Four channel TMDSsignals
Signal source:pattern generator format (Refer to the SPEC)
1.2.6Audio
Amplifier andheadphone section :
Outputpower:2x2Wrms into 16 Ohm
Inputsensitivity: 500mVrms
Frequencyrange:100Hz - 20KHz
Volume control keypads are at the front control panel.
L/R inputvia1.8m hard-wiredcable with limegreen3.5mm plug
Headphone connection will mute speakers.
Loudspeaker section :
Ratedinput2.0W
Max. input3.0W
Impedance 16 Ohm+/- 15%
Sensitivity76 dB +/-3 dB (at 1W/1mat 1KHz)
1.2.7Input connectors
(1) InputanalogD-sub connector pin assignment
PIN No.SIGNAL
1Redvideo input
2Green video input/ sync on green
3Bluevideo input
4GND
5GND
6Redvideo GND
7Greenvideo GND
8Bluevideo GND
9DDC +3.3V or +5V
10 Logic GND-Cable detect
11 GND
12Serial data line (SDA)
13H-sync /H+V
14V-sync
15Data clockline (SCL)