Philips V40 109B6 User manual

Service
Service
Service
Published by BCU Monitors Printed in Suzhou Copyright reserved Subject to modification F Sep. 24 2004
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC
EQUIPMENT CONTAINING HIGH VOLTAGES.
SAFETY NOTICE
GB 3138 106 10426
V40 109B6
Model: 109B60/00

2
Proper service and repair is important to the safe, reliable
operation of all Philips Consumer Electronics Company**
Equipment. The service procedures recommended by
Philips and described in this service manual are effective
methods of performing service operations. Some of these
service operations require the use of tools specially designed
for the purpose. The special tools should be used when and
as recommended.
It is important to note that this manual contains various
CAUTIONSandNOTICESwhichshouldbecarefullyreadin
order to minimize the risk of personal injury to service
personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to
understand that these CAUTIONS and NOTICES ARE NOT
EXHAUSTIVE. Philips could not possibly know, evaluate and
advise the service trade of all conceivable ways in which
service might be done or of the possible hazardous
consequences of each way. Consequently, Philips has not
undertaken any such broad evaluation. Accordingly, a
servicer who uses a service procedure or tool which is not
recommended by Philips must first satisfy himself thoroughly
that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method
selected.
* * Hereafter throughout this manual, Philips Consumer
Electronics Company will be referred to as Philips.
Critical components having special safety characteristics are
identified with a by the Ref. No. in the parts list and
enclosed within a broken line* (where several critical
components are grouped in one area) along with the safety
symbol on the schematics or exploded views.
Use of substitute replacement parts which do not have the
same specified safety characteristics may create shock, fire,
or other hazards.
Under no circumstances should the original design be
modified or altered without written permission from Philips.
Philips assumes no liability, express or implied, arising out of
any unauthorized modification of design.
Servicer assumes all liability.
WARNING
* Broken Line
FORPRODUCTSCONTAININGLASER:
Invisible laser radiation when open.
AVOIDDIRECTEXPOSURETOBEAM.
Use of controls or adjustments or
performance of procedures other than
those specified herein may result in
hazardous radiation exposure.
The use of optical instruments with this
product will increase eye hazard.
DANGER-
CAUTION-
CAUTION-
TO ENSURE THE CONTINUED RELIABILITY OF THIS
PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S REPLACEMENT
PARTS, WHICH ARE LISTED WITH THEIR
PARTNUMBERSINTHEPARTSLISTSECTIONOFTHISSERVICE
MANUAL.
Important Safety Notice
109B6 CRT
Go to cover page
!
!

Technical Data 109B6 CRT 3
I. Basic Data
1.Description:Auto-Scan UltraHigh Resolution Digital Color Monitor
2. Commercial Release:Sep, 20,2004
3.CRT:
Screen size:19"Flat SquareConventiontube
Diagonal VIS : 18”
Shadow Mask : Invar
DotPitch :0.26mm for SDI, LG & CPTCRT
Horizontal pitch :0.21mm for SDI, LG & CPTCRT
Deflectionangle :90 degrees
Aspect ratio:4:3
Source :LG/SDI/CPT
Surface :Anti-reflection/Anti-static
Visible screen area :360 mm x 270mm
Blackmatrix:Yes
Phosphors : P22
Magnetic field:North
4. Commercial name:Philips
5. ScanningFrequency
Horizontal :30 -97 KHz
Vertical :50-160 Hz
6.Maximum resolution:1920x1440@60 Hz
Recomm. resolution:1280x1024 @ 75 Hz
7. Over-scan :Yes
8. Monitor modes
Factory modes:40
Usermodes:16
"
ItemResolutionFreq. V x H Pixel rate(Mhz) Remark
160(31.469k) 25.175 VGA
2 72(37.861k) 31.500 VESA
375(37.500k) 31.500 VESA
4 @ 85(43.269k) 36.000 VESA
5100(50.60k) 40.500 SNI
6
640x480
67(35.0k) 30.240MAC-º
770(31.5k) 25.100 VGA
8
640x350
85(37.8k) 31.500 VESA
9@70(31.469k) 28.321VGA
10
720x400
85(37.927k) 35.500 VESA
11 60(37.879k) 40.000 VESA
12 72(48.077k) 50.000 VESA
13 75(46.875k) 49.500 VESA
14 @ 85(53.674k) 56.250VESA
15100(63.90k) 67.500 SNI
16 56(35.16k) 36.000 VESA
17
800x600
90(60.4k) 65.227 SIEMENS
18832x624 75(49.725k) 57.280MAC-º
19 @60(48.363k) 65.000 VESA
20@70(56.476k) 75.000 VESA
2175(60.000k) 78.750VESA
22 @ 85(68.677k) 94.500 VESA
23@
1024x768
90(72.54K) 99.82 SIEMENS
24 @ 70(63.850K) 94.500 VESA
25 75(67.500k) 108.000 VESA
26
1152x864
85(77.090K) 121.500 VESA
27 1152x87075(68.681k) 100.000 MAC
28 1152x900 76(71.800k) 108.000 SUN
2960(60.000k) 108.000 VESA
30 @
1280x960
85(85.938k) 148.500 VESA
31 60(63.981k) 108.000 VESA
32 @ 75(79.976k) 135.000 VESA
33 @
1280x1024
85(91.146k) 157.500 VESA
3460(75.000k) 162.000 VESA
3565(81.250k) 175.500 VESA
36 @70(87.500k) 189.000 VESA
37@
1600x1200
75(93.75k) 202.50VESA
381792x1344 60(83.640k) 204.750VESA/P
39 1856x139260(86.330k) 218.250VESA/P
401920x144060(90.000k) 234.000 VESA/P
“@“Denote it isapreset mode,others arepreloadmodes.
""
PIN No. SIGNAL
1Red
2Green
3 Blue
4Sense(GND)
5SelfTest
6RedGND
7Green GND
8BlueGND
9Notconnect
10 Sync GND
11 Sense(GND)
12Bi-directional data(SDA)
13 H-sync
14V-sync
15DDC Data clock(SCL)
Inputsignal Pin assignment:
II. PicturePerformance
1.Displaysize
Recommended:355x265mm
Maximum : 360 x270mm
2. Maxvideopixel :234Mhz
3.Rise/Fall time:<6.5ns/<6.5ns
4. Misconvergence
(A/Czone):£0.25 / 0.35(Zone A/Cis0.3/0.4 When ? 45kHz).
center:£0.15
5. Geometry distortion:
|Top|, |Bottom| : : £2.0mm
|Left|, |Right|:£2.0mm
ôTop + Bottom ô:£3.5 mm
ôLeft+Rightô:£3.5 mm
Waviness per50mm:1.0mm max. at maximum videosize
Slopepolaritychanges: 1.0mm max.
Tilt :£2.0mm
6.Imagerotation:1degree adjustable
7. Horizontal /Vertical linearity:
12equal blocks alonghorizontal axis,
9equal blocks alongvertical axis. (see Fig-1)
Horizontal frequency<33KHz 33K~ 65KHz >65KHz
Horizontal non-linearity: £7.5 % £6.5 % £6%
Vertical non-linearity: £5% £5% £5%
Horizontal two adjacent:£6%£6%£5%
Vertical two adjacent:£5% £5% £5%
Xmax. - Xmin
H. linearity = ----------------------- x 100%
Xmax. + Xmin.
Ymax. - Ymin
V. linearity = ------------------------ x 100%
Ymax. + Ymin.
8. Imagestabilityafterwarm -up 30 minutes.
As afunctionof brightness : < 1.0%
As afunctionof supplyinputvoltage:<1.0%
As afunctionof temperature:<1.0%
9.Brightness uniformity : >75%
10.White uniformity:x,y<±0.015
11.DisplayCentering:|A-B|or|C-D|<6mm(for all preset modes)
12. White color CIE coordinates
@9300K ±27MPCD :x=0.283+/- 0.015
y=0.297+/- 0.015
@6500K ± 27MPCD :x=0.313 +/- 0.015
y=0.329+/- 0.015
@5500K ±27MPCD :x=0.332+/-0.015
y=0.347 +/- 0.015
@sRGB:x=0.313 +/- 0.015
y=0.329+/- 0.015
+/-
+/-
+/-
+/-
13.White tracking: +/- 0.015on centerwith light outputfrom 3
FL tomaxFL.
14. Brightness output:(9300 K) 68.67K/85Hz
Brightness ContrastFW Pattern10X10cmblock
ControlControlfL fL
Min Min <0.2
CenterMin £0.25
CenterMax30 +/- 2.5 41+/ - 3
Go to cover page

4Technical Data
109B6 CRT
Go to cover page
14.1.sRGBluminance (Full white pattern): at 68.67K/85Hz, regardless
of brightness andcontrastcontrols: 23 +/- 2.5 FL
15.Imageshiftrange:Horizontal:> 10 mm, +/-3 from centertoeach side.
Vertical:> 8 mm, +/-2 from centertoeach side.
III. CustomerRelevance
1.Front Controls:Contrasttactswitch control
(With DecreaseandIncrease)
(LefttoRight)Brightness tact switch control
(With DecreaseandIncrease)
OSDmenutact switch control
Poweron/off button
2. RearControl:15-pin D-sub I/F cable.
Digital OSDControls
-Language.Chinese
.English
Espanol
Francais
Deutsch
Italiano
.Portuguese
.Korean
- Zoom .Zoom
-AdjustHorizontal .Position
.Size
-AdjustVertical Position
.Size
-AdjustShape.Adjustsidecurve.Pincushion
.Balanced
.Adjustsideangles. Trapezoid
.Parallelogram
.Rotate image.Rotate
-AdjustColor .9300Kforgeneral use
.6500Kforimagemanagement
.5500Kforphotoretouch
.sRGB
.UserPreset R,G,B
-Reset tofactory settings .No
.yes
-Extracontrols.Adjustmoire.Horizontal
.Vertical
Degauss
.LightFrame<Off On>
.Serial No.
Resolution
.Frequency
-Model select (underfactotory mode)CPTCRT:set 109B6 CPTON
LPD&SDICRT:set 109B6 LG & SDION
.SWDDC set ON
.LF ONOSDset ON
.LF3 set ON
-Closemain controls
(Moredetailsaboutstructureareprovidedin SoftwareCRS)
3. RearInterconnection:PowerCord: 1.8 m plugable,3leadwith
groundlead
I/F connectors : 15pin 1.8m D-sub flyingin cable
4.DDC :Compliant with the VESA DDC2Bstandards
DDC1 DDC2B
SoftwareV
Hardware
See DDC DATA
5. MainsVoltageRange:195-264 or 90-264 Vrms
6InputLine Frequency: 47-63Hz
7. Powerconsumption:< 75W (at 220Vac mains)
< 78W (at 110Vac mains)
8. PowerLEDgreen (non-protruding)
**Note1: 78&79Factory code
Brazil :HC(48H,43H)
Chung-Li:TY(54H,59H)
Delta :GK(47H,4BH)
Suzhou : BZ(42H,5AH)
Juarez : YA(59H,41H)
Shenzshen :CX(43H,58H)
Szombathely:HD(48H,44H)
Raleigh:IO(49H,4FH)
Series No. address : 82,83,84,85,86,87,88,89
9. PowerManagement TCO-99,EPAand E2000
Functionality: Status LEDcolor
Ongreen (normal operation)
Off flashgreen (< 1.0W)
10. Low radiation:TCO/MPRº
11.Separated EHT:Yes
12. DAF : Yes
13. Selftest:Yes
IV. Quality
1.MTBF:>75000 hr. (excl.CRT)
2. Target F.C.R.:target £2%(first12months)
3. Environment :operating/non-operatingshipping/storage
Temperature0to40 -25 to65
Humidity10 %to90 % 5%to95%
nocondensation incl.condensation
butexcl.rain
Altitude:10000 ft39000 ft
Shock/vibration:AccordingDSDstandard
4.Environmental issues:CRT,cabinet andcomponentsmustbe
free of CFC's,
PBBE's, PBDE's, cadmium, (TCO99)
All documentationprintedonrecycledpaper
Accessoriespackedin bufferwithoutadditional
wrapping
All otherissuesaccordingCEandBUEnvironmental
Policy
V. Regulatory Compliance
1.Safety & Ergonomics:UL1950
CSA-22.2 No. 950-M89
IEC950
ZH1/618
EN60950
EMKO-TSE (74SEC)207/94
ISO 9241-3 / ISO 9241-7 / ISO 9241-8
E-2000,EPA,Nutek, TUV/GS,TCO.
2. EMI/RFI/EMS :EN55022 class B
FCC Part15(class B)
D.O.C.(class B)
CISPR22 (class B)
C-tick, CE(Europe)
EMS: EN61000-4-3(80%1KHz AM modulation)picturejitter4mm
3. X-Ray:DHHS 21CFRSubchapterJ
Rontgen VerordnungRov 1987-01-08
4.EMCstandards : EN 50082-1
EN 60555-2
5. Low Radiation:TCO/MPRº
6.CompatibilityPC99,Windows2000,Windows ME, PC2001
Windows XP.
VI. ApprobationCompliance
1. Approvals&Certifications: UL, CSA, SEMKO, TUV/GS,
FCC Class B,DOC.Class B,BZT,VCCIclass 2,
FDA(DHHS), Rontgen,TUV/Ergonomics, CE(98,
prepared), B”-mark for Poland, C tick for Australia
PSB(Singapore), BCIQ, CCIB
</=
"- "

Go to cover page
109B6 CRT 5
Installation
Front View
Power button switchesyour monitoron.
OK button which whenpressed will take youto the OSD controls
Contrast hotkey. Whenthe "-" button is pressed, the adjustment
controls forthe CONTRASTwill show up.
Brightness hotkey. Whenthe "+" button is pressed, the adjustment
controls forBRIGHTNESS will show up.
"-" and "+" buttons,are used foradjustingthe OSD ofyour monitor
RearView
1.Power in -attach power cable here.
2. VideoIn-this is a cable which is already attached to
your monitor. Connectthe other endofthe cableto your PC.

6
109B6 CRT
Go to cover page
Trouble Shooting
Having thisproblem? Check theseitems
Makesure the Power cable ispluggedinto the
power outlet andback ofthe monitor.
NoPicture Power button in the front ofyour monitor shouldbe
in the ON position.
(Power LED not lit)Disconnectthemonitor fromthe power outlet
for about one minute.
NoPicture Makesure the computer isturnedon.
Makesure the monitor cable isproperlyconnectedto your computer.
(Power LED isflashing green)Check to see ifthe monitor cable has bent pins.
The EnergySaving feature may be activated
NoPicture Makesure the Brightness andContrastcontrolsare set correctly.
Makesure the monitor cable isproperlyconnectedto your computer.
(Power LED isgreen)Check to see ifthe monitor cable has bent pins.
Makesure the computer Power button ison.
Screen doesn'tshow Makesure the monitor cable isproperlyconnectedto your computer.
(Alsorefer to the Quick Start Guide).
when you turn on the monitor Check to see ifthe monitor cable has bent pins.
Makesure the computer isturnedon.
Nocolor or intermittent color If you are using anon-VESA-DDCstandardvideo card,
turn the DDC1 /2Bfeature Off.
The picture may needdegaussing.
Color appearsblotchyRemoveanynearby magneticobjects.
Facethemonitor towardthe Eastfor the bestpicture quality.
Check the Color Temperature.
Missing one or more colors Makesure the monitor cable isproperlyconnectedto your computer.
Check to see ifthe monitor cable has bent pins.
Adjust the Brightness andContrastcontrols.
DimPicture Check your video cardandit's owner's manualinstructions
for it may be anon-VESA-DDCStandardcard.
AdjusttheHorizontaland/or VerticalSize.
Picture istoo large or too small AdjusttheZoom.
Edgesofthe picture are not square Adjustthegeometry
Picture has a double image Eliminate the useofavideo extension cable and/or video switchbox.
Facethemonitor towardthe Eastfor the bestpicture quality
Picture isnot sharpCheck to makesure Moiréisswitchedoff.
AdjustSyncInput.
Unstable Picture Increaseyour refreshrate
Problemwith OnScreen Display Refer to the instructionsandtroubleshooting information in thatchapter.

109B6 CRT 7
OSD Tree
Go to cover page

8
Go to cover page
The OSD Controls
BRIGHTNESS
To adjust your screen's brightness, follow the steps below. Brightness
is the overall intensity of the light coming from the screen. A 50%
brightness is recommended.
1) Press the button on the monitor. The BRIGHTNESS window
appears.
2) Press the or button to adjust the brightness.
3) When the brightness is adjusted to the level desired. Stop pressing
the or button and after three seconds the BRIGHTNESS
window will disappear with the new adjustment saved.
Smart Help After the BRIGHTNESS window has disappeared, to
continue to the CONTRAST window, follow the steps under CONTRAST.
CONTRAST
To adjust your screen's contrast, follow the steps bellow. Contrast is
thedifferencebetweenthelightanddarkareasonthescreen.A100%
contrast is recommended.
1) Press the button on the monitor. The CONTRAST window appears.
2) Press the or button to adjust the contrast.
3) When the contrast is adjusted to the level desired, stop pressing
the or button and after three seconds the CONTRAST window
will disappear with the new adjustment saved.
Smart Help After the CONTRAST window has disappeared, to continue
to the MAIN CONTROLS, follow the steps under LANGUAGE.
LANGUAGE
The ON SCREEN DISPLAY shows its setting in one of eight languages.
The default is English, but you can select French, Spanish, German,
Italian, simplify-Chinese, Korea, Brazilian or Portuguese.
1) Press the button the monitor. The MAIN CONTROLS window
appears. LANGUAGE should be highlighted.
2) Press the button again. The LANGUAGE window appears.
3) Press the or button until the desired language is highlighted.
4) press the button to confirm your selection and return to MAIN
CONTROLS window. Close MAIN CONTROLS will be highlighted...
Smart Help After returning to MAIN CONTROLS......to continue to
ZOOM.
ZOOM
ZOOM increase or decrease the size of the images on your screen.
To adjust the ZOOM follow the steps below.
1) Press the button on the monitors. The MAIN CONTROLS
window appears.
2) Press the or button until ZOOM is highlighted.

Go to cover page
3) Press the button. The ZOOM window appears.
4) Press the or button to adjust ZOOM.
5) Press the button to confirm your selection and return to the MAIN
CONTROLS window. Close MAIN CONTROLS will be highlighted.
Smart Help After returning to MAIN CONTROLS...
... to continue to ADJUST HORIZONTAL, press the or button until
ADJUST HORIZONTAL is highlighted. Next, follow steps3-7 under ADJUST
HORIZONTAL.
... To exit completely, press the button.
ADJUST HORIZONTAL under ADJUST HORIZONTAL shifts the image on
your screen either to the left or right. Use this feature if your image does
not appear centered. ADJUST SIZE under ADJUST HORIZONTAL expands
or controls the image on your screen, pushing it out toward the left and
right sides or pulling it in toward the center.
1) Press the button on the monitor. The MAIN CONTROLS window
appears.
2) Press the or button until ADJUST HORIZONTAL is highlighted.
ADJUST HORIZONTAL
3) Press the button. The ADJUST HORIZONTAL window appears.
ADJUST POSITION should be highlighted.
4) Press the or button to move the image to the left or right.
5) When the position is adjusted, press the button to return to
MAIN CONTROLS window, or press the to highlight ADJUST SIZE.
6) To adjust the horizontal size, press the or button.
7) When the size is adjusted, press the button to return to MAIN
CONTROLS window. CLOSE MAIN CONTROLS will be highlighted.
Smart Help After returning to MAIN CONTROLS...
... To continue to ADJUST VERTICAL, press the button until ADJUST
VERTICAL is highlighted. Next, start with step 3 under ADJUST VERTICAL
and follow the directions.
...To exit completely, press the button.
ADJUST VERTICAL
ADJUST POSITION under ADJUST VERTICAL shifts the image on your
screen either up or down. Use this feature if your image does not
appear centered. ADJUST VERTICAL expands or controls the image on
your screen, pushing it out toward the top or bottom or pulling it in
toward the center.
1) Press the button on the monitor. The MAIN CONTROLS window
appears.
2) Press the button until ADJUST VERTICAL is highlighted.
3) Press the button. The ADJUST VERTICAL window appears.
ADJUST POSITION should be highlighted.

Go to cover page
4) Press the or button to move the image up or down.
5) When the position is adjusted, press the button to return to
MAIN CONTROLS window, or press the button to highlight
ADJUST SIZE.
6) To adjust the vertical size, press the or button.
7) When the size is adjusted, press the button to return to MAIN
CONTROLS window. CLOSE MAIN CONTROLS will be highlighted.
Smart Help After returning to MAIN CONTROLS...
... To continue to ADJUST SHAPE, press the button until ADJUST
SHAPE is highlighted. Next, start with step under ADJUST SHAPE and
follow the directions.
... To exit completely, press the button.
ADJUST SIDE CURVE
ADJUST SIDE CURVE under ADJUST SHAPE allows you to adjust two
of the five preset options. These two options are PINCUSHION and
BALANCED pincushion. Note: use these features only when the picture
is not square.
1) Press the button on the monitor. The MAIN CONTROLS window
appears.
2) Press the button until ADJUST SHAPE is highlighted.
3) Press the button. The ADJUST SHAPE window appears.
ADJUST SIDE CURVE should be highlighted.
ADJUST SHAPE
4) Press the button. The SIDE CURVE window appears.
PINCUSHION should be highlighted.
5) To adjust the pincushion, press the or button, then
press the button to save your selection.
6) When the pincushion is adjusted, press the button to
highlight BALANCE or press the button to return to the
ADJUST SHAPE window.
7) To adjust the balanced, press the or button.
8) When the balanced is adjusted, press the button. BACK TO
ADJUST SHAPE will be highlighted.
9) Press the button to return to the ADJUST SHAPE window, then
press the button until ADJUST SIDE ANGLES is highlighted.
Smart Help After returning to MAIN CONTROLS...
... To continue to ADJUST SIDE ANGLES, start with step 5 under
ADJUST SIDE ANGLES and follow the directions.
...To exit completely. Press the button twice.
ADJUST SIDE ANGLES under ADJUST SHAPE allows you to adjust
two of the five preset options. These two options are TRAPEZOID
and PARALLELOGRAM. Note: use these features only when the
picture is not square.
1) Press the button on the monitor. The MAIN CONTROLS
window appears.
2) Press the button until ADJUST SHAPE is highlighted.
ADJUST SIDE ANGLES

OSD Adjustments (Continued) 109B6 CRT
Go to cover page
11
3) Press the button. The ADJUST SHAPE window appears.
ADJUST SIDE CURVE should be highlighted.
4) Press the button to highlight ADJUST SIDE ANGLES.
5) Press the button. The SIDE ANGLES window appears.
TRAPEZOID should be highlighted.
6) To adjust the trapezoid, press the or button, then
press the button to save your selection.
7) When the trapezoid is adjusted, press the button to
highlight PARALLELOGRAM or press the button to return
to the ADJUST SHAPE window.
8) To adjust the PARALLELOGRAM, press the or button.
9) When the parallelogram is adjusted, press the button to return
to the ADJUST SHAPE window. BACK TO MAIN CONTROLS window
will be highlighted.
10) Press the button to return to the MAIN CONTROLS window, or
press the button until ROTATE IMAGE is highlighted.
Smart Help After returning to MAIN CONTROLS...
... To continue to ROTATE IMAGE, start with step 5 under ROTATE IMAGE
and follow the directions.
...To exit a completely, press the button twice.
...To adjust only the PARALLELOGRAM, follow steps 1-4 above, then
press the button, and follow steps 7-9
ROTATE IMAGE under ADJUST SHAPE allows you to adjust the rotated
image. Note : use this feature only when the picture is not square.
1) Press the button on the monitor. The MAIN CONTROLS window
appears.
2) Press the button until ADJUST SHAPE is highlighted.
ROTATE IMAGE
3) Press the button. The ADJUST SHAPE window appears.
ADJUST SIDE CURVE should be highlighted.
4) Press the button until ROTATE IMAGE is highlighted.
5) Press the button. The ROTATE IMAGE window appears.
ROTATE will be highlighted.
6) To adjust the rotation, press the or button.

12
109B6 CRT
Go to cover page
7) When the rotation is adjusted, press the button to return to
the ADJUST SHAPE window. BACK TO MAIN CONTROLS should
be highlighted.
8) Press the button to return to MAIN CONTROLS.
Smart Help After returning to MAIN CONTROLS...
... To continue to ADJUST COLOR, press the button until ADJUST
COLOR is highlighted. Next, start with step 3 under ADJUST COLOR
and follow the directions.
... To exit completely, press the button twice.
ADJUST COLOR
Your monitor has two preset options you can choose from. The first
option is for GENERAL USE, which is fine for most applications. The
second option is for GAMES, which is for playing computer games.
When you select one of these options, the monitor automatically
adjusts itself to that option. There is also a third option, USER PRESET,
which allows you to adjust the colors on your screen to a setting you
desire.
1) Press the button on the monitor. The MAIN CONTROLS window
appears.
2) Press the button until ADJUST COLOR is highlighted.
3) Press the button. The ADJUST COLOR window appears.
4) Press the or button to highlight 9300K for GENERAL
USE. 6500K for GAMES, or USER PRESET.
5) Once you have highlighted the GENERAL USE OR GAMES, press
the button to confirm your selection and return to the MAIN
CONTROLS window. CLOSE MAIN CONTROLS will be highlighted.
6) If USER PRESET is highlighted, press the button to highlight
RED(GREEN BLUE). Next, press the or button to adjust
the color red(green blue).
7) When all adjustments are complete, press the button until
RESET TO FACTORY SETTINGS is highlighted. Next, start with
step 3 under RESET TO FACTORY SETTINGS.
...To exit completely, press the button.
RESETTOFACTORYSETTINGS
RESETTOFACTORYSETTINGSreturnseverythinginallthewindows
to factory presets.
1) Press the button on the monitor. The MAIN CONTROLS window
appears.
2) Press the button until RESET TO FACTORY SETTING is
highlighted.
3) Press the button. The RESET TO FACTORY SETTINGS
window appears.
4) Press the or button to select YES or NO. NO is the
defaults. YES return all settings to their original factory
adjustments.
OSD Adjustments (Continued)

OSD Adjustments (Continued) 109B6 CRT
Go to cover page
13
5) Press the button to confirm your selection and return to the MAIN
CONTROLS window. CLOSE MAIN CONTROLS will be highlighted.
Smart Help After returning to MAIN CONTROLS...
... To continue to EXTRA CONTROLS, press the button until EXTRA
CONTROLS is highlighted. Next, start with step 3 under EXTRA CONTROLS.
...To exit completely, press the button.
ADJUST MOIRE
EXTRA CONTROLS is a set of three feature, including ADJUST MOIRE.
Moire is a fringe patten arising from the interference between two
superimposed line pattens. To adjust your moire, follow the steps below.
Note: use only if necessary. By activating ADJUST MOIRE, sharpness can
be affected.
1) Press the button on the monitor. The MAIN CONTROLS window
appears.
2) Press the button until EXTRA CONTROLS is highlighted.
EXTRA CONTROLS
3) Press the button. The EXTRA CONTROLS window appears.
ADJUST MOIRE will be highlighted.
4) Press the button. The ADJUST MOIRE window appears.
HORIZONTAL will be highlighted.
5) To adjust the horizontal moire, press the or button.
6) When the horizontal moire is adjusted, press the button to
highlight VERTICAL.
7) To adjust the vertical moire, press the or button.
8) When the vertical moire is adjusted, press the button to return
to the EXTRA CONTROLS window. BACK TO MAIN CONTROLS will
be highlighted.
Smart Help After returning to MAIN CONTROLS...
... To continue to DEGAUSS, press the button until DEGAUSS is
highlighted. Next, start with step 3 under EXTRA CONTROLS,
DEGAUSS.
...To exit completely, press the button.
EXTRA CONTROLS is a set of three feature, including DEGAUSS.
Degaussing remove electromagnetic build up that may distort the color
on your screen.
1) Press the button on the monitor. The MAIN CONTROLS window
appears.
2) Press the button until EXTRA CONTROLS is highlighted.
DEGAUSS
1280X1024
80K/75HZ

OSD Adjustments (Continued)
14
109B6 CRT
Go to cover page
3) Press the button. The EXTRA CONTROLS window appears.
ADJUST MOIRE will be highlighted.
4) Press the button until DEGAUSS is highlighted.
5) To degauss your screen, press the button. Your screen will be
degaussed, then the MAIN CONTROLS will reappear. CLOSE MAIN
CONTROLS will be highlighted.
Smart Help After returning to MAIN CONTROLS...
...To exit completely, press the button.
CLOSE MAIN CONTROLS
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.
If the monitor is functioning properly, you will see a OSD message
asshowninthefollowingillustration:
This box also appears during normal system operation if the video
cable becomes disconnected or damaged. This box will remain on
for one minute, go off five seconds. Then on for one minute, and will
repeat cycle.
1. Turn off your monitor and reconnect the video cable:
then turn on both your computer and the monitor.
2. While in self-test mode, the LED remains green and the pattern
remains on and stationary.
If your monitor screen still remains dark after you use the previous
procedure, check your video controller and computer system; your
monitor is functioning properly.
NO SIGNAL INPUT
If there is something wrong with the input signal, a message appears
on the screen although the power indicator LED is still on. The
message may indicate that the monitor is NO SIGNAL INPUT or that
you need to check the signal cable.
CHECK SIGNAL CABLE
NO SIGNAL INPUT
Monitor specific troubleshooting
Self-test Feature Check(STFC)
Your monitor provides a self-test feature that allows you to check
whether your monitor is functioning properly. If your monitor and
computer are properly connected but the monitor screen remains
dark, run the monitor self-test by performing the following steps:

OSD Adjustments (Continued) 109B6 CRT
Go to cover page
15
OSD LOCK
OSD LOCK is a feature which disables the OSD controls. It can be used
when the monitor is set up for demonstration purposes or when
adjustment of the OSD is not desirable.
Switch on OSD LOCK feature:
Press and hold the button continuously for 15 seconds.
Release the button when the message
" CONTROL MENU IS LOCKED" appears.
Switch off OSD lock feature:
Press and hold the button continuously for 15 seconds or until
the message window ''CONTROL MENU IS LOCKED''disappears. And
''MAIN CONTROLS'' appears.
To access factory mode
1. Turn off monitor(don't turn off PC)
2. Press and simultaneously on the front control pane,
then press , wait until the OSD menu with characters
V32 107T6 V0.24 20040303 (below OSD menu) come on the screen
of monitor.
3. If OSD menu disappears on the screen of monitor, press
again(anytime), then the OSD menu comes on the screen again.
4. Using : to select OSD menu.
5. Using : to increase or decrease the setting.
6. Using : to access/confirm the selection.
7. After alignment of factory mode, turn off monitor(if you do not run
off monitor, the OSD menu is always at the factory mode), then turn
on monitor again (at this moment, the OSD menu goes back to user
mode.)
To leave factory mode
To access BURN IN mode
First of all, monitor displays an image.
1. Disconnect the video cable(interface cable).
2. Turn off monitor
3. Press and simultaneously on the front control panel,
then the BURN IN mode comes on the screen of monitor as below.
50 seconds around
5 second around
repeat
4. Reconnect the video cable, then return the normal image.
SERVICE MODE (indication-factory mode)
Default setting of MODEL SELECT
MODEL SELECT
Factory
Mode
Indicator
-----------
MODEL SELECT
-----------
MODEL SELECT
V32 107T6 V0.24 20040303V40 109 V0.12 20040621
37067
V40 109 V0.12 20040621

16 Mechanical Instructions
109B6 CRT
Go to cover page
Control connector
Degaussing wire connector
Fig. 5
Screw
Pedestal ass'y
Screw
Fig. 1
Clip
CRT grounding wire
Video Panel Fig. 3
0. General
To be able to perform measurements and repairs on the "circuit
boards", these unit should placed in the service position first.
1. Remove the rear cover in Fig. 1 and Fig. 2.
-Remove 4 screws as shown
-Remove back cover as shown
-Remove pedestal as shown
2. Video panel
-Disconnect the wire between metal shield of video panel and
CRT neck as shown in Fig. 3.
-Disconnect the CRT grounding from Video panel.
-Remove screw grounding and grounding wire in Fig. 4.
3. Main board connector in Fig. 5.
-Disconnect york wire
-Disconnect rotation connector
-Disconnect control board connector
-Remove Screw for fixed I/F cable
-Remove signal connector
-Remove degaussing wire connector
Screw-grounding Fig. 4
Fig. 2
===================>
Screw

Mechanical Instructions 109B6 CRT
Go to cover page
17
Screw
Fig. 6
Fig. 6
Video panel Main panel
Fig. 9 SERVICE POSITION
Pull-up
Fig. 8
4. Main panel with Bottom Tray
-Remove the screws for disconnect the Bottom tray as Fig. 6.
-Open the click and remove the screws on the main board from
fig. 6 to fig.7.
5. SERVICE POSITION
-reconnect connectors, some wires and panels (chassis),
service position can be available for DC/AC measurement
as shown inFig.8 Fig. 9.
Fig.7
Fig.9

DDC Instructions
18
109B6 CRT
Go to cover page
General
DDC Data Re-programming
Analog DDC IC, & EEPROM
Additional information
In case the DDC data memory IC or main EEPROM which storage all
factory settings were replaced due to a defect, the serial numbers have
to be re-programmed" ".
It is advised to re-soldered DDC IC and main EEPROM from the old
board onto the new board if circuit board have been replaced, in this
case the DDC data does not need to be re-programmed.
Additional information about DDC (Display Data Channel) may be
obtained from Video Electronics Standards Association (VESA). Extended
Display Identification Data(EDID) information may be also obtained from
VESA.
1. An i486 (or above) personal computer or compatible.
2. Microsoft operation system Windows 95/98 .
Y o Install the EDID_PORT_Tool under Win2000/XP . As
Fig. 1 .
A. Cody the "UserPort.sys" to C:\WINNT\system32\drivers(win2000)
C:\WINDOWS\system32\drivers(winXP)
B. Running " io.exe" everytime, Before you start to programming
edid data .
4. A/D Alignment kits (12NC: 3138 106 10079) shown as Fig. 2:
inclusion : a. Alignment box x1
b. Printer cable x1
c. (D-Sub) to (D-Sub) cable x1
Note: The EDID301.EXE is a windows-based program, which cannot
beruninMS-DOS.
System and equipment requirements
ou have t
3. EDID301.EXE program
Pin assignment
15-pin D-Sub Connector
Configuration and procedure
There is no Hardware DDC (DDC IC) anymore. Main EEPROM stores
all factory settings and DDC data (EDID code) which is also called
Software DDC. The following section describes the connection and
procedure for Software DDC application. The main EEPROM can be re-
programmed by enabling '' factory memory data write'' function on the
DDC program (EDID301.EXE).
Initialize alignment box
In order to avoid that monitor entering power saving mode due
to sync will cut off by alignment box, it is necessary to initialize
alignment box before running programming software
(EDID301.EXE). Following steps show you the procedures and
connection.
Step 1: Supply 8-12V DC power source to the Alignment box by
plugging a DC power cord .
Step 2: Connecting printer cable and D-Sub cable of monitor as Fig. 3
Fig. 3
PC 1=Power connector
2=D-SUB connector
To printer port (LTP1)
DC Power
8-12 V
Printer
Port
To
Monitor
To PC
12
----->
----->
Fig. 2
Fig. 1
PIN No. SIGNAL
1Red
2Green
3Blue
4 Sense (GND)
5 Self Test
6RedGND
7Green GND
8BlueGND
9 Not connect
10 Sync GND
11 Sense (GND)
12 Bi-directional data(SDA)
13 H-sync
14 V-sync
15 DDC Data clock(SCL)
+
109B6
AC POWER

DDC Instructions (Continued) 109B6 CRT
Go to cover page
19
Step 3: Installation of EDID301.EXE
Method 1: Start on DDC program
Start Microsoft Windows.
1.Copy the Program"EDID301.EXE" in service manual cd-rom to C:\ .
2. Click , choose Run at start menu of Windows as shown
In Fig. 4.
Fig. 4
4. Click button. The main menu appears (as shown in Fig. 6).OK
This is for initialize alignment box.
Fig. 6
Fig. 5
Fig. 7
Note 1: If the connection is improper, you will see the following error
message (as shown in Fig. 7) before entering the main menu.
Meanwhile, the (read EDID) function will be disable. At this
time, please make sure all cables are connected correctly and
fixedly, and the procedure has been performed properly.
3. At the submenu, type the letter of your computer's hard disk drive
followed by :EDID301 (for example, C:\EDID301, as shown in Fig. 5).
Note 2: During the loading, EDID301 will verify the EDID data which
just loaded from monitor before proceed any further function,
once the data structure of EDID can not be recognized, the
following error message will appear on the screen as below.
Please confirm following steps to avoid this message.
1. The data structure of EDID was incorrect.
2. DDC IC that you are trying to load data is empty.
3. Wrong communication channel has set at configuration setup
windows.
4. Cables loosed or poor contact of connection.
1
Fig. 8
Re-programming EEPROM(Software DDC IC)
Step 1: After initialize alignment box, connecting all cables and
box as shown in Fig. 9
Fig. 10
Step 2: Read DDC data from monitor
1. Click icon as shown in Fig. 10 from the tool bar to bring up
the Channels "Configuration Setup" windows as shown in Fig. 11.
Fig. 9
1=Power connector
2=D-SUB connector
PC
To printer port (LTP1)
DC Power
8-12V
Printer
Port
To
Monitor
To PC
12
----->
----->
To PC Video port (D-sub)
+AC IN

DDC Instructions (Continued)
20
109B6 CRT
Go to cover page
To Monitor
D-sub/DVI cable
DC 8~12V
To Printer port
Step 3: Modify DDC data (verify EDID version, week, year)
1. Click (new function) icon from the tool bar, bring up
Step1of9asshowninFig.13.
EDID301 DDC application provides the function selection and
text change (select & fill out) from Step 1 to Step 9.
Step 4: Modify DDC data (Monitor Serial No.)
Next
1. Click , bring up Fig. 14.
2. Click , bring up Fig. 15.
Next
3. Click OK button to confirm your selection.
4. Click icon (Read EDID function) to read DDC EDID data from
monitor. The EDID codes will display on screen as shown in Fig. 12.
Fig. 14
Fig. 15
2. Select the DDC2B as the communication channel.
As shown in Fig. 11.
Fig. 11
Fig. 12
Fig. 13
Don't close this screen. --->
Fig. 16
3. Click , bring up Fig. 16.
Next