Philips SV16 Series User manual

Philips Lighting North America Corporation
200 Franklin Square Drive
Somerset, NJ 08873, USA
Phone: [phone]
www.philips.com/luminaires
Philips Lighting Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Phone: [phone]
www.philips.com/luminaires
9140052682 February 2016
SV16 Series
6V 11W
120/277V 60Hz Emergency Luminaire
Damp Location Standard
Wet Loc. / Battery Heater Optional
INSTALLATION AND
OPERATING
INSTRUCTIONS
IMPORTANT
SAFEGUARDS
When using electrical equipment, basic safety
precautions should always be followed, including
the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
All servicing should be performed by qualified
personnel only.
Equipment should be mounted in locations and at
heights where it will not be readily subjected to
tampering by unauthorized personnel.
The use of accessory equipment not recommended
by the manufacturer may cause an unsafe condition.
Do not use this equipment for other than intended
use.
Do not let power supply cords touch hot surfaces.
Do not mount near gas or electric heaters.
CAUTION: Halogen cycle lamp(s) are used in
this equipment. To avoid shattering: Do not
operate lamp in excess of rated voltage, protect
lamp against abrasion and scratches and against
liquids when lamp is operating, dispose of lamp
with care.
Halogen cycle lamps operate at high temperatures.
Do not store or place flammable materials near
lamp.
CAUTION: “To avoid electrical overload, total
connected lamp load (factory and field installed)
should not exceed output rating”.
Do not use this equipment for other than intended
use. SAVE THESE
INSTRUCTIONS
WARNING –Shut off AC power to branch circuits
to which units will be connected. All wiring should
be per National Electrical Code and local
regulations.

Philips Lighting North America Corporation
200 Franklin Square Drive
Somerset, NJ 08873, USA
Phone: [phone]
www.philips.com/luminaires
Philips Lighting Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Phone: [phone]
www.philips.com/luminaires
9140052682 February 2016
Installation
(1): For junction box mounting (wet or damp location units) –Remove large center knockout for
wiring access and remove necessary mounting knockouts. Fasten backplate to junction box using two
#8-32x1-1/4” screws supplied. For wet location units, ensure that the gasket is evenly compressed
around perimeter.
For installation using surface conduit (damp location units only) –Remove necessary mounting
knockouts and secure conduit to flange provided at top of backplate. Mount backplate to wall using
mounting hardware supplied by others.
Connect AC Harness found in electronics module to AC supply. Refer to hookup instructions below:
(2): If battery heater option has been ordered, installer must finish wiring heater according to
installation voltage. All connections are to be made inside electronics module.

Philips Lighting North America Corporation
200 Franklin Square Drive
Somerset, NJ 08873, USA
Phone: [phone]
www.philips.com/luminaires
Philips Lighting Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Phone: [phone]
www.philips.com/luminaires
9140052682 February 2016
(3): Re assemble AC harness assembly to mating plug inside electronics module. Connect battery
harness to charger board. Install electronics module to backplate by hinging together at top and snapping
together at bottom. Two #6x1/2” screws are provided for further securing electronics module to
backplate if so desired. Install lamps provided by snapping into ceramic lamp holders on lamp head.
Attach cover by snapping over electronics module. Cover will latch onto edge of backplate in three
locations. Tamper proof screw may be driven into unit to secure installation against vandalism.

Philips Lighting North America Corporation
200 Franklin Square Drive
Somerset, NJ 08873, USA
Phone: [phone]
www.philips.com/luminaires
Philips Lighting Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Phone: [phone]
www.philips.com/luminaires
9140052682 February 2016
OPERATING INSTRUCTIONS
(1): Energize AC power to equipment and check that pilot lamp illuminates red.
(2): Press test switch and verify pilot lamp turns off and lamp heads illuminate.
(3): Leave AC connected for a minimum of 24 hours before performing any extended testing. Full
recharge of battery may take up to one (1) week.
NOTE
A. This equipment is provided with a lockout feature whereby connecting battery leads prior to
energizing AC power will not turn on the emergency lamps. After AC power is energized, the
emergency lamps will turn on upon AC power failure.
B. This equipment is provided with a low battery disconnect feature which prevents full discharge
of battery. If the building is to be unoccupied for an extended period and AC is shut off, the battery
should be disconnected from the charger to prevent damage.
C. The battery in this unit is sealed and requires no maintenance.
SERVICING
(1): For servicing, remove tamper proof screw (if installed). Then remove cover by inserting a small
screwdriver or similar tool into the hole in the bottom of the cover and press upward to release locking
tab. Pull over up and off of unit.
(2): Remove electronics module from backplate by inserting a flat bladed screwdriver between
backplate and module and prying module away from backplate.