Philips PVD1079/12 User manual

Quick Start Guide
Install TV set stand
Charge
Setup DVB-T
Setup AnalogueTV
Plug in USB storage drive
and SD card
A
B
C
D
E
Portable TV PVD1079
PVD1079_12_QSG_Eng.indd 1PVD1079_12_QSG_Eng.indd 1 2008-02-01 3:26:48 PM2008-02-01 3:26:48 PM

2
1
Install TV set stand
A
1
2
Align the catches on the stand base with the slots at the
bottom of the set as shown.
Fit the stand into the slots and turn anticlockwise until
you hear a "click" sound.
NOTE
See the user manual for how to release
the stand.
PVD1079_12_QSG_Eng.indd 2PVD1079_12_QSG_Eng.indd 2 2008-02-01 3:26:51 PM2008-02-01 3:26:51 PM

BCharge
1
2
IMPORTANT: For the first time to power on the set, use the AC
power adaptor.
3
Connect the supplied adaptor to the set and the AC outlet.
The RED light comes on.
The battery pack will be fully charged in approximately
6 hours. When the RED light goes off, it means that the
battery pack is fully charged.
TIPS
1. Your battery will continue to charge while the player
is in use. The RED light will appear and it will take
approximately 8 hours to fully charge the battery pack.
2. The environment temperature should be between 0°C
and 35°C. To protect the electronic insides, the player
will stop charging when too cold or too hot.
PVD1079_12_QSG_Eng.indd 3PVD1079_12_QSG_Eng.indd 3 2008-02-01 3:26:52 PM2008-02-01 3:26:52 PM

CSetup DVB-T
1
2
3
Before you start searching TV channels,
connect your TV to the antenna as shown.
Press POWER 2; on the main unit
or 2on the remote to switch on the TV.
To set up DVB-T, press SETUP > DTTV. The player
will guide you through the DVB-T setup automatically.
Enjoy the TV program by using the control keys on the
remote.
4
Antenna connection
Home antenna
TIPS
1. For best reception, connect the PVD1079 to the home antenna. Auxiliary
antenna is used when there is excellent signal coverage.
2. The unit is designed to receive digital signals only, and it does not support
analog radio such as FM or AM.
NOTE
When travelling to another country, it is possible to lose current TV programs.
Carry out an Auto search by following these steps:
1. Press SETUP > DTTV > Country.
2. Select your country.
3. Select Auto search.
PVD1079_12_QSG_Eng.indd 4PVD1079_12_QSG_Eng.indd 4 2008-02-01 3:26:53 PM2008-02-01 3:26:53 PM

5
DSetup AnalogueTV
1
2
3
Before you start searching analogue TV channels,
connect your TV to the antenna as shown.
Press SOURCE > ATV.
Press SETUP > Auto Store to select your country.
Press 2; to start scanning. All channels found will be
automatically stored after scanning is complete.
Enjoy the TV program by using the control keys on the
remote.
4
Antenna connection
NOTES
1. When travelling to another country, it is possible to lose current TV
programs. Carry out an Auto store by repeating steps 2 to 4.
2. The supplied cable antenna is not good for analogue TV reception,
please connect the player to the home antenna.
Home antenna
PVD1079_12_QSG_Eng.indd 5PVD1079_12_QSG_Eng.indd 5 2008-02-01 3:26:53 PM2008-02-01 3:26:53 PM

EPlug in USB storage drive
and SD card
\ |
1
2
Connect your USB drive or SD card as shown.
You can playback the digital content in your storage media,
such as:
Photo: JPGE files
Video: DivX® or MP4 files
Music: MP3 or WMA
➜
➜
➜
© Royal Phipips Electronics N.V. 2008
All rights reserved.
WK0805
PVD1079_12_QSG_Eng.indd 6PVD1079_12_QSG_Eng.indd 6 2008-02-01 3:26:54 PM2008-02-01 3:26:54 PM