Philips BT6000A/94 User manual

www.philips.com/support
User manual
Always there to help you
Register your product and get support at
BT6000
Question?
Contact
Philips

1EN
Contents
1 Important 2
2 Your Bluetooth speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 4
3 Get started 5
Power supply 5
Turn on/off 6
Adjust volume 6
4 Use Bluetooth devices 7
Connect a device 7
Play from Bluetooth device 8
Control your phone call 8
Disconnect a device 8
Reconnect a device 8
5 Listen to an external device 9
6 Product information 10
Specications 10
7 Troubleshooting 11
General 11
About Bluetooth device 11
8 Notice 12
Care of the environment 12
Trademark notice 12

2EN
1 Important
Warning
• Never remove the casing of this speaker.
• Never place this speaker on other electrical equipment.
• Keep this speaker away from direct sunlight, naked
amesorheat.
• Make sure that you always have easy access to the
power cord, plug, or adaptor to disconnect the speaker
from the power.
• Make sure that there is enough free space
around the speaker for ventilation.
• After use under humid circumstance,
immediately clean the product with a soft
dry cloth.
• The battery shall not be exposed to
excessiveheatsuchassunshine,reorthe
like.
• The adapter shall not be exposed to
dripping or splashing.
• Noobjectslledwithliquidsshallbe
placed on the adapter.
• Use only power supplies listed in the user
manual.
• Where the plug of the Direct Plug-in
Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.

3EN
2 Your Bluetooth
speaker
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
This speaker has passed splash-proof test
(IPX4) and can be used near water.
With this speaker, you can enjoy audio from
Bluetooth-enabled devices or other external
devices.
What's in the box
Check and identify the contents of your
package:
• Speaker
• USB cable for charging
• Power adapter
• Short user manual

4EN
Overview of the speaker
a PAIRING
• Enter Bluetooth pairing mode.
• Disconnect Bluetooth connection.
• Answer or reject an incoming call.
• End the current phone call.
• Transfer the call to your mobile device.
b NFC
• Connect a NFC compatible device
through Bluetooth.
c
• Charge the built-in battery.
d AUDIO IN
• Connect an external audio device.
e Volume knob ( )
• Adjust volume.
• Turn the speaker on or off.
a
c
b
d
e

5EN
3 Get started
Always follow the instructions in this chapter in
sequence.
Power supply
Either AC power or battery can be used as
power supply of this product.
Option 1: Battery power
The speaker can operate on the built-in
rechargeable battery.
Note
• Rechargeable battery has a limited number of charge
cycles. Battery life and number of charge cycles vary by
use and settings.
• It takes approximately three hours to fully charge the
battery.
• TheredLEDindicatorasheswhenthebatteryislow.
To recharge the built-in battery:
• Connect the speaker to AC power supply;
or
• Connect the USB cable between
• the socket on the speaker, and
• a USB socket on a computer.
LED indicator Battery status
Solid red Under charging
Off Fully charged
Option 2:AC power
Caution
• Risk of product damage! Make sure that the power
voltage corresponds to the voltage printed on the back
or underside of the speaker.
• Risk of electric shock! When you unplug the AC adapter,
always pull the plug from the socket. Never pull the cord.

6EN
• Connect the adapter to:
• the socket on the speaker.
• the power outlet.
Turn on/off
• To turn the speaker on or off, rotate the
knob clockwise or anticlockwise until you
hear a click.
» When the speaker is turned on, the
blueLEDindicatorashes.
» When the speaker is turned off, the
blue LED indicator lights off, and the
and the icons are towards the same
direction.
OFF
ON
Note
• Ifthebatterylevelislow,theredLEDindicatorashes.
Switch to standby mode
• The speaker switches to standby mode in
the following situations:
• The connection with Bluetooth
device or other device is invalid for 15
minutes; or
• Music playback is stopped for 15
minutes.
Adjust volume
• During play, rotate the knob to increase or
decrease volume.

7EN
4 Use Bluetooth
devices
With this speaker, you can listen to audio from
Bluetooth-enabled devices and control the
incoming call through Bluetooth.
Connect a device
Note
• The speaker can memorize a maximum of four paired
devices.Thefthpaireddevicewillreplacetherstone.
• Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
• Any obstacle between this speaker and a Bluetooth
device can reduce the operational range.
• Keep away from any other electronic device that may
cause interference.
• Make sure that no audio input cable is connected to
the AUDIO IN socket.
Option 1: Connect a device through
NFC
Near Field Communication (NFC) is a
technology that enables short-range wireless
communication between various NFC
compatible devices, such as mobile phones and
IC tags.
If your Bluetooth device supports NFC, you can
connect it with this speaker easily.
1 Enable NFC on your Bluetooth device
(refer to its user manual).
2 Turn on the speaker.
» TheblueLEDindicatorashes.
3 Tap the NFC tag on the top of the speaker
with the NFC area of your Bluetooth
device.
4 Follow the on-screen instructions to
complete the pairing and connection.
» After successful connection, the
speaker beeps twice, and the LED
indicator turns solid blue.
Option 2: Connect a device manually
Note
• The operational range between this speaker and a
Bluetooth device is approximately 10 meters (30 feet).
1 On your Bluetooth device, enable
Bluetooth and search for Bluetooth devices
that can be paired (see the user manual of
the device).
2 Turn on the speaker.
» TheblueLEDindicatorashes.

8EN
3 Select [Philips BT6000] displayed on your
device for pairing. If necessary, input “0000”
as the pairing password.
» After successful connection, the
speaker beeps twice, and the LED
indicator turns solid blue.
• Ifyoufailtond[Philips BT6000] on
your device for pairing, press and hold
PAIRING until you hear beep sound,
and then try again.
LED indicator Description
Flashing blue Connecting;
Waiting for pairing
Solid blue Connected
Play from Bluetooth device
Note
• If there is an incoming call on the connected mobile
phone, music play pauses.
After successful Bluetooth connection, play
audio on the Bluetooth device.
» Audio streams from your Bluetooth
device to the speaker.
Control your phone call
After Bluetooth connection, you can control an
incoming call with this speaker.
Button Function
Press to answer an incoming call.
Press and hold for three seconds to
reject an incoming call.
During a call, press to end the current
call.
During a call, press and hold for three
seconds to transfer the call to your
mobile device.
Disconnect a device
• Press and hold PAIRING for three seconds
when there is no incoming call;
• Disable Bluetooth on your device; or
• Move the device beyond the
communication range.
» The speaker beeps twice, and the blue
LEDindicatorashes.
Note
• Before connecting another Bluetooth device, disconnect
thecurrentdevicerst.
Reconnect a device
When you turn on the speaker, it will reconnect
the last connected device automatically; If not,
select [Philips BT6000] on your Bluetooth
device to start connection.