Philips FWM396 User manual

DVD Micro System FWM396
TABLE OF CONTENTS
3141 785 32590
DB 0814
2008
Location of PCBS ............................................................ 1-1
Specifications ................................................................. 1-2
Measurement Setup ....................................................... 1-3
Service Aids, Safety Instruction, etc. .............................. 1-4
Instructions On CD Playability .............................. 1-5 to 1-6
Service Test Program .................................................... 2-1
Disassembly Diagram .................................................. 3-1
Block Diagram ................................................................. 4-1
Wiring Diagram................................................................. 4-2
MCU & Front Board ....................................................... 5
Circuit diagram ............................................................ 5-1
Layout diagram.................................................. 5-2...5-3
HI-Amp & lOW - Amp Board............................................. 6
Circuit diagram .................................................. 6-1...6-2
Layout diagram............................................................ 6-3
MAIN Board...................................................................... 7
Circuit diagram ............................................................ 7-1
Layout diagram............................................................ 7-2
CD Board ...................................................................... 8
Circuit diagram ............................................................ 8-1
Layout diagram............................................................ 8-2
Power Board ................................................................. 9
Circuit diagram ............................................................ 9-1
Layout diagram............................................................ 9-2
Explode View ................................................................. 10
Service Partlist ................................................................. 11
/55/BK/78

du
VERSION VARIATIONS :
Type /Versions:
Features
Board in used:
FWD396
Service policy
MAIN BOARD
FRONT/MCU BOARD
CD BOARD
POWER BOARDPOWER BOARD
* TIPS : C -- Component Lever Repair.
M -- Module Lever Repair
√
-- Used
/55
/55
/BK
/BK
/78
/78
Feature diffrence
C
M
Type /Versions:
FWD396
Hi-AMP & LOW-AMP BOARD
AMP BOARD
TUNER BOARD
Location of PCBS
1-1
Hi-AMP BOARD
LOW-AMP BOARD
FRONT/MCU BOARD
MAIN BOARD
POWER BOARD
MM
MMM
CC
CCC
CCC
CCC
CCC

1-2
Electronic specification
AMPLIFIER
1 kHz
(low channel - both channels driven)
................................................... 50 W per channel (6 Ω)
10 kHz
(high channel - both channels driven)
................................................... 50 W per channel (6 Ω)
Total output power............................................. 200 W
Signal-to-noise ratio .......................... ≥60 dBA (IEC)
Frequency response .......................... 50 – 16000 Hz
Input sensitivity
AUX/Line In ............................................................. 2 V
Microphone ....................................................... 1.5 mV
Output
Speakers ............................................................. ≥6 Ω
(1) (6 
1 kHz, 10% THD)
CD/MP3-CD PLAYER
Number of programmable tracks ............................... 40
Frequency response ...................... 50 – 16000 Hz -3dB
Signal-to-noise ratio ....................................... ıG%$
Channel separation .......................... ıG%N+]
7otal harmonic distor tion ................................. < 0.6%
MPEG 1 Layer 3 (MP3-CD) ..................... MPEG AUDIO
MP3-CD bit rate ......................................... 32-256 kbps
(128 kbps advised)
Sampling frequencies ....................... 32, 44.1, 48 kHz
TUNER
FM wave range ...................................... 87.5 – 108 MHz
AM wave range (9 kHz) ......................... 531 – 1602 kHz
SPEAKERS
System 1-way; 1 port bass reflex
Impedance ................................................................ 6
Woofer .................................................................. 1 x 5"
Tweeter............................................................... 1 x 1.5"
Dimensions (w x h x d) . 207 x 309 x 214 (mm)
Weight ................................................... 2.8 kg each
GENERAL
Material/finish ................................... Polystyrene/Metal
AC Power ............................ 110 – 127 / 220 – 240V;
................................................... 50/60 Hz Switchable
Power Consumption
Active ............................................................... 110 W
Dimensions (w x h x d) ..265 x 310 x 403 (mm)
Weight (without speakers)................................. NJ
Specifications and external appearance are
subject to change without notice.
Ω
Ω

1-3
LF Generator
e.g. PM5110
Recorder
Use Universal Test Cassette CrO2 SBC419 4822 397 30069
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
S/N and distortion met
e
e.g. Sound Technology ST170
L
R
DUT
or Universal Test Cassette Fe SBC420 4822 397 30071
LEVEL METER
e.g. Sennheiser UPM550
with FF
-
filter
S/N and distortion meter
e.g. Sound Technology ST1700B
L
R
DUT
CD
Use Audio Signal Disc
(replaces test disc 3)
SBC429 4822 397 30184
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
S/N and distortion meter
e.g. Sound Technology ST1700B
Frame aerial
e.g. 7122 707 89001
Tuner AM (MW,LW)
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday´s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).
RF Generator
e.g. PM5326
Ri=50:
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
RF Generator
e.g. PM5326
S/N and distortion meter
e.g. Sound Technology ST1700B
Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).
Ri=50:
Tuner FM
MEASUREMENT SETUP

1-4
SERVICE AIDS
GB WARNING
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
ESD
CLASS 1
LASER PRODUCT
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used
Safety components are marked by the symbol !.
Lead free

Set remains closed!
N
Y
Play a CD
for at least 10 minutes
Y
playability
ok ?
N
playability
ok ?
add Info for customer
"SET OK"
check playability
N
Y
playability
ok ?
check playability
check playability
return set
Customer complaint
"CD related problem"
"fast" lens cleaning
1
2
3For flap loaders (= access to CD drive possible)
cleaning method 4is recommended
INSTRUCTIONS ON CD PLAYABILITY
1-
Exchange CDM
1-4For description - see following pages

1
PLAYABILITY CHECK
For sets which are compatible with CD-RW discs
use CD-RW Printed Audio Disc ....................7104 099 96611
TR 3 (Fingerprint)
TR 8 (600μ Black dot) maximum at 01:00
• playback of these two tracks without audible disturbance
playing time for: Fingerprint t10seconds
Black dot from 00:50 to 01:10
• jump forward/backward (search) within a reasonable time
For all other sets
use CD-DA SBC 444A..................................4822 397 30245
TR 14 (600μ Black dot) maximum at 01:15
TR 19 (Fingerprint)
TR 10 (1000μ wedge)
• playback of all these tracks without audible disturbance
playing time for: 1000μ wedge t10seconds
Fingerprint t10seconds
Black dot from 01:05 to 01:25
• jump forward/backward (search) within a reasonable time
2
CUSTOMER INFORMATION
It is proposed to add an addendum sheet to the set which
informs the customer that the set has been checked
carefully - but no fault was found.
The problem was obviously caused by a scratched, dirty or
copy-protected CD. In case problems remain, the customer
is requested to contact the workshop directly.
The lens cleaning (method 3) should be mentioned in the
addendum sheet.
The final wording in national language as well as the printing
is under responsibility of the Regional Service Organizations.
4
LIQUID LENS CLEANING
Because the material of the lens is synthetic and coated
with a special anti-reflectivity layer, cleaning must be done
with a non-aggressive cleaning fluid. It is advised to use
“Cleaning Solvent
The actuator is a very precise mechanical component and
may not be damaged in order to guarantee its full function.
Clean the lens gently (don’t press too hard) with a soft and
clean cotton bud moistened with the special lens cleaner.
The direction of cleaning must be in the way as indicated in
the picture below.
Before touching the lens it is advised to clean the
surface of the lens by blowing clean air over it.
This to avoid that little particles make scratches on
the lens.
INSTRUCTIONS ON CD PLAYABILITY
1-

SERVICE TEST PROGRAM
2 - 1 2 - 1
To enter service mode,keep
TITLE+ & MAX key depressed
for 3 Seconds while plugging the
main AC cord.
Display shows
Ver: x.x
disc1
Display lights
all the screen
Display shows
NEW
stop All settings will be
reset to default
settings
if no button is pressed within 90s
exit factory mode
automatically

Disassembly Diagram
3-1 3-1

4-1 4-1
Block Diagram
FRONT/MCU BOARD
MAIN BOARD AMP BOARD

4-24-2
Wiring Diagram

5-1
5-1
MCU & FRONT BOARD - Circuit Diagram

5-2
5-2
MCU & FRONT BOARD - Layout Diagram - top view

5-3
5-3
MCU & FRONT BOARD - Layout Diagram - bottom view

6-1
6-1
HI-AMP & LOW-AMP BOARD - Circuit Diagram - 1
IC

6-2
6-2
HI-AMP & LOW-AMP BOARD - Circuit Diagram - 2
IC

6-3
6-3
HI-AMP & LOW-LOW AMP BOARD - Layout Diagram

7-1
7-1
MAIN BOARD - Circuit Diagram

7-2
7-2
MAIN BOARD - Layout Diagram

8-1
8-1
CD BOARD - Circuit Diagram