Philips 29PT6961-79R User manual

Instructions for use
Colour Television
29PT6961
3139 125 28821

2
LASER SAFETY
This unit employs a laser. Due to possible eye
injury, only a qualified service person should
remove the cover or attempt to service this
device.
USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
LASER
Type Semiconductor laser GaAIAs
Wave length 650 nm (DVD)
780 nm (VCD/CD)
Output Power 7 mW (DVD)
10 mW (VCD/CD)
Beam divergence 60 degree
Manufactured under license from Dolby
Laboratories. “Dolby”and the double-D
symbol are trademarks of Dolby
Laboratories. Confidential unpublished
works. © 1992-1997 Dolby laboratories.
All rights reserved.
TruSurround and the SRS symbol are
trademarks pf SRS Labs., Inc.
TruSurround technology is manufactured
under license from SRS Labs., Inc.
LASER SAFETY
NEVER MAKE OR CHANGE
CONNECTIONS WITH THE
POWER SWITCHED ON.
The TV-DVD Combi player is
in conformity with the EMC
directive and low-voltage directive.
CAUTION – VISIBLE AND INVISIBLE
LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
CAUTION WARNING LABEL IS
LOCATED ON THE BACKCOVER
OF THE SET.
The region code for this set is 3.
Since it is usual for DVD movies to be
released at different times in different
regions of the world, all players have
region codes and disc can have an
optional region code. If you load a disc
of a different region code to your
player, you will see the region code
notice on the screen.The disc will not
play and should be unloaded.
TV SAFETY
• Disconnect mains plug when :
– the red light below the TV screen is flashing continuously.
– a bright white line is displayed across the screen.
– cleaning the TV screen. Never use abrasive cleaning agents. Use a slight damp chamois
leather or soft cloth.
– there is a lightning storm.
– the set is left unattended for a prolonged period of time.
• Do not place your TV set under direct sunlight or heat.
• Avoid placing your set (e.g. near the window) where it is likely to be exposed to rain
or water.
• Do not leave your set on standby mode for a prolonged period of time. Switch off set
to allow it to be demagnetised.A demagnetised set supports good picture quality.
• Do not shift or move the set around when it is switched on. Uneveness in colour in
some parts of the screen may occur.
• Never attempt to repair a defective TV yourself.Always consult a skilled service personnel.
3
CLASS 1
LASER PRODUCT

3
INTRODUCTION
Thank you for purchasing this televison set.You are now the proud owner of a PHILIPS
Home-Cinema TV set which promises full value to you as a customer. Please read the
instruction manual carefully and thoroughly to help you install and operate your TV set.
TABLE OF CONTENTS
LASER SAFETY ........................................................................................................................ 2
TV SAFETY ........................................................................................................................ 2
BEFORE CALLING SERVICE (TV) ........................................................................................ 4
BEFORE CALLING SERVICE (DVD) .................................................................................... 5
PREPARATION .......................................................................................................................... 6
CONNECTING THE A UDIO/VIDEO SOCKETS
Playback ....................................................................................................................................7
Recording .................................................................................................................................9
SETTING OF TV/DVD SWITCH .......................................................................................... 10
FUNCTIONS OF REMOTE CONTROL (TV)............................................................................11
FUNCTIONS OF REMOTE CONTROL (DVD)........................................................................13
FUNCTIONS OF TV/DVD CONTROLS ................................................................................14
SELECTING THE MENU LANGUAGE AND A UTOMATIC TUNINGOF CHANNELS............ 15
MANUAL TUNING OF CHANNELS........................................................................................ 17
SELECTING THE COLOUR/SOUND SYSTEM..........................................................................18
FINE TUNING OF CHANNELS .............................................................................................. 19
SORTING OF CHANNELS.........................................................................................................20
EDITING OF CHANNELS..........................................................................................................21
NAMING OF CHANNELS..........................................................................................................22
USING THE PICTURE/SOUND MENU.................................................................................... 23
ACTIVATING THET IMER...........................................................................................................24
ACTIVATING THE CHILD LOCK
Access Code............................................................................................................................26
Change Code...........................................................................................................................27
Lock Channel...........................................................................................................................28
Clear All.................................................................................................................................... 29
USING THE SURF CONTROL.................................................................................................. 30
USING THE SCREEN FORMAT.................................................................................................31
USING THE ROTATION FEATURE ...........................................................................................32
USING THE PROGRAM LISTING CONTROL ......................................................................... 33
SMART PICTURE AND SMART SOUND.................................................................................. 34
USING THET ELETEXT............................................................................................................. 35
OPERATING THE DVD
General .................................................................................................................................... 36
User Preference .....................................................................................................................40
Playing a DVD-Video disc .................................................................................................... 46
Playing a VIDEO-CD disc ..................................................................................................... 47
General Features ................................................................................................................... 48
Special DVD Features ...........................................................................................................51
Special VCD Features ...........................................................................................................52
Favourite Track Selections.................................................................................................... 53
SPECIFICATIONS........................................................................................................................54
Recycling Directive
Your TV set uses materials which are reusable or which can recycled. To minimise the
amount of waste in the environment, specialist companies recoverused sets for
dismantling and collection of reusable materials (consult your dealer).

4
BEFORE CALLING SERVICE (TV)
Below is a list of frequently occurred symptoms for the TV. Before you call service, make these
simple checks. Some of these symptoms can easily be rectified if you know what to do.
Symptom What you should do
Colour patch • Switch off the TV by the mains power button.Wait for 20
(uneveness) minutes before switching on again.
• Check the TV is not placed too near speakers or magnetic
objects.
No power • Check the TV’s AC power cord is plugged into the mains
socket. If there is still no power, disconnect plug.Wait for
60 seconds and re-insert plug. Switch on the TV again.
No picture • Check the antenna connection at the rear of the TV.
• Possible TV station problem.Try another channel.
Good picture • Try increasing the volume.
but no sound • Check that the sound is not muted. If it is muted, press the
(mute) button on the remote control to restore sound.
Good sound but poor • Try increasing the contrast and brightness setting.
colour or no picture
Snowish picture and • Check antenna connection at the rear of the TV.
noise
Horizontal dotted lines • Possible electrical interference e.g. hairdryer, vacuum
cleaner, etc. Switch off appliances.
Double images or • Possible poor positioning of antenna. Using a highly
“Ghost” images directional antenna may improve reception.
TV not responding to • Check life span of batteries of remote control handset.
remote control handset • Aim remote control handset directly at remote control
sensor lens on the TV.
HH
HH
H

5
BEFORE CALLING SERVICE (DVD))
Below is a list of frequently occurred symptoms for the DVD. Before you call for service, make
these simple checks. Some of these symptoms can easily be rectified if you know what to do.
Symptom What you should do
No power • Check if both plugs of the power cord are properly
connected.
• Check if there is power at the AC outlet by plugging in
another appliance.
No picture • Check if the TV is switched on.
• Check the video connection.
Completely distorted • If the picture is distorted completely or if the picture rolls
picture or no colour vertically, make sure the NTSC/PAL setting at the DVD
with player menu player matches the video signal of your television.
If your TV video signal is NTSC, select NTSC setting at
the DVD player. If your video signal is PAL, select the PAL
setting (Refer to section on “Selecting the Colour/Sound
System).
Distorted or Black/White • The disc format does not match your TV’s video signal
picture with DVD orVideo (PAL/NTSC).
CD
Distorted sound from HiFi • Check to make sure that no audio connections are made to
ampliflier the amplifilier phono input.
No audio at digital output • Check the digital connections.
• Check the settings menu to make sure the digital output is
set to ALL or PCM.
• Check if the audio format of the selected audio language
matches your receiver capabilities.
Disc cannot be played • Ensure the disc label is facing up.
• Clean the disc. Wipe the disc from the center out. Note : Do
not use solvents such as benzine, thinner, commercially
available cleaners or anti-static spray intended for analog discs.
• Check if the disc is defective by trying another disc.
• Check to see if the disc is badly scratched or warped.
No return to start-up • Reset by switching the player off, then, on again.
screen when disc is • Check to see if the program requires another disc to be
removed loaded.
Player does not respond • Aim remote control directly at the sensor on the front of
to the remote control the player.
• Remove any obstacles between the player and the remote
control.
• Inspect or replace the batteeries in the remote control.
Buttons do not work • Set the player in standby by using the STANDBY button on
the front of the player. Press STANDBY button again to set
the player back to ON.
Player does not respond • Operations are not permitted by the disc. Refer to the
to all operating commands instructions of the disc.
during playback

6
PREPARATION
Positioning of the TV set
• Place your TV set on a solid base, strong enough to
withstand the weight of the set.
• Leave a space of at least 5 cm around each side of the
TV set to allow for proper ventilation.
• Do not place TV set near a radiator or other sources of
heat.
• Do not place TV set where it can be exposed to rain or
excesssive moisture.
Connecting the Aerial
• Insert the aerial plug into the socket ¬at the rear of
the set.
Connecting to the mains
• Insert the mains plug into the wall socket. (For correct
mains voltage, refer to the type sticker at the rear of the
set).
Note :This diagram is not representative of the actual
plug and socket.
Using the Remote Control
• Insert the correct type of batteries into the compartment.
• Ensure the batteries are placed in the right direction.
Note : Remove the batteries from the remote
control handset if handset is not used for a long time.
Switching on the TV set
• Press the mains power button to switch on/off the TV set.
• If the set is on standby mode (indicator light is red), press
the Standby button on the remote control to switch on set.
5 cm 5 cm
5 cm
ÉÑ
ÉÑ
ÉÑ

7
CONNECTINGTHE AUDIO/VIDEO SOCKETS (PLAYBACK)
You can view the playback of VCR tapes (Video Disc players, camcorders, etc.) by using the AUDIO
and VIDEO INPUT sockets on the rear of the TV.
– Connect the VIDEO and AUDIO IN sockets on the rear of the TV to the AUDIO and
VIDEO OUT sockets on the VCR.
The S-Video connection on the rear of theTV is used for the playback of S-VHS VCR tapes,Video
Discs, Video Games or Compact Disc-Interactive (cd-i) discs. Better picture detail and clarity is
possible with the S-Video playback as compared to the picture from a normal antenna (RF)
connection.
– Connect the S-VIDEO socket on the rear of the TV to the S-VHS OUT socket on a
S-VHS VCR.
– Connect the AUDIO IN sockets from the rear of the TV to the AUDIO OUT sockets
on the VCR.
Note : You need not connect the VIDEO IN socket of the TV if S-VIDEO IN socket is
connected.
AV sockets
on rear of
TV
AV sockets
on rear of
TV
Back of
VCR
VCR (Equipped with
Video and Audio
Output sockets
ANTENNA
OUT
IN
OUT
IN
AUDIO
RL
VIDEO
IN
OUT
L/Mono
R
S-VIDEO
VIDEO
AUDIO
AV1
in
AV2
in
Monitor
out
OPTICAL
COAXIAL
DIGITAL AUDIO OUT
PCM / MPEG2 / AC-3 / DTS
ANTENNA
OUT
IN
OUT
IN
AUDIO
RLVIDEO
IN
OUT OUT
S-VIDEO
L/Mono
S-VIDEO
VIDEO
AUDIO
AV1
in
AV2
in
Monitor
out
OPTICAL
COAXIAL
DIGITAL AUDIO OUT
PCM / MPEG2 / AC-3 / DTS
Back of S-VHS VCR

8
CONNECTINGTHE AUDIO/VIDEO SOCKETS (PLAYBACK)
For more convenient direct playback connections, the Side Audio/Video Input sockets allow for quick
and easy connections, particularly Camcorder tape recordings.
– Connect the S-VIDEO socket (if available) from the Camcorder to the Side S-VIDEO
socket of the TV. You need not connect the Side VIDEO IN socket of theTV if the
S-VIDEO socket is connected.
– Connect the AUDIO OUT sockets (Right and Left) from the Camcorder to the Side
AUDIO IN sockets.
Side Audio/Video
Input sockets
Camcorder
Connect headphone jack
to socket for personal
listening
CONNECTING TO THE AMPLIFIER W ITHT WO CHANNEL
DIGITAL STEREO (PCM)
• Connect the TV’s digital audio “out” jack (optical or coaxial) to the corresponding “in” jack
on your amplifier.
• You will need to activate the player’s diigital output(See User Preferences)
ANTENNA
OUT
IN
OUT
IN
AUDIO
RL
VIDEO
IN
OUT
L/Mono
R
S-VIDEO
VIDEO
AUDIO
AV1
in
AV2
in
Monitor
out
OPTICAL
COAXIAL
DIGITAL AUDIO OUT
PCM / MPEG2 / AC-3 / DTS
AMPLIFIER
VCR (Equipped with
Video and Audio
Output sockets
AV sockets on
rear of TV

9
CONNECTINGTHE AUDIO/VIDEO SOCKETS (RECORDING)
Connection for recording from the TV channel
– Connect the corresponding INPUT sockets of the VCR to the MONITOR OUTPUT
sockets on the rear of the TV.
– To enhance the sound of your TV, connect the AUDIO L and Rsockets to an external
audio system instead of theVCR. For mono equipment, connect only the AUDIO L socket.
Connection for recording from one VCR to another VCR
– Connect the sockets of the VCR which you wish to record from, to the corresponding
sockets at either AV1 or AV2..
– Connect the sockets of the receiving VCR to the MONITOR OUTPUT sockets on the
rear of the TV.
AV sockets on
rear of TV
VCR (Equipped with
Video and Audio
Output sockets
ANTENNA
OUT
IN
OUT
IN
AUDIO
RL
VIDEO
IN
OUT
L/Mono
R
S-VIDEO
VIDEO
AUDIO
AV1
in
AV2
in
Monitor
out
OPTICAL
COAXIAL
DIGITAL AUDIO OUT
PCM / MPEG2 / AC-3 / DTS
AV sockets
on rear of
TV
VCR (Equipped with
Video and Audio Input
sockets
ANTENNA
OUT
IN
OUT
IN
AUDIO
RL
VIDEO
IN
OUT
ANTENNA
OUT
IN
OUT
AUDIO
RL
VIDEO
OUT
L/Mono
R
S-VIDEO
VIDEO
AUDIO
AV1
in
AV2
in
Monitor
out
OPTICAL
COAXIAL
DIGITAL AUDIO OUT
PCM / MPEG2 / AC-3 / DTS
VCR (Equipped with Video
and Audio Input sockets
VCR 2
VCR 1
Back of
VCR

10
➥
NOTE
This set performs 2 functions, that as , a TV set and
a DVD PLAYER.
TV Viewing
• For set to perform as a TV, the TV/DVD switch
MUST be set to TV position on the remote control.
If switch is at DVD position, functions of remote
control for TV operation will be disabled .
DVD Playback
• For set to perform as a DVD player, the TV/DVD
switch MUST be set to DVD position on the
remote control. If switch is at TV position, functions
of remote control for DVD operation will be disabled
except for Sleeptimer, Volume + / – , Mute and
Smart Picture and Sound buttons
Note
• If you want to adjust picture and sound settings or
features while you are in DVD mode, the TV/DVD
switch must be at the TV position to enable you to
enter into the TV remote command mode.
• Press the MENU button to enter into the main
menu. For picture and sound adjustments, refer to
the section on “Using the Picture and Sound menu”
• To return to DVD mode, reset the switch to DVD
position.
SETTING OF TV/DVD SWITCH
➥

11
FUNCTIONS OF REMOTE CONTROL (TV)
11
12
5
6
7
1
2
3
4
4
\
m
INCR. SURR.
PROG. LISTSURF
INCR. PIC
T/C AUDIO FTS ANGLE
Éá á
ç
Ç
àà
Å
8
9
13
10
1SLEEPTIMER
Allows you to select a time period after
which the set will switch to standby mode
automatically.
2OSD
– Displays the channel number, sound and
colour transmission mode, status of the
sleeptimer., channel name (if channel is
named) and the current time (if current
time is being entered in the Timer menu).
– Also allows you to exit menu from screen.
3AV
Allows you to select the AV channels.3
4TV/DVD Switch
Allows you to select between TV or DVD
mode.When TV is in operation, ensure switch
is at TV position. Likewise,when DVD is in
operation, switch must be in DVD position.
5DIGIT (0 -9)
Allows you select a channel.
Note : For a 2-digit number, the second digit
must be entered before the “–” sign disappears.
6SMART SOUND
Allows you to select your desired sound
setting from 4 types of sound settings.
7MENU
Displays main menu. Also exits menu from
screen.
8CURSOR UP
Allows you to select the next item on the
menu.
9CURSOR LEFT
Allows you to access the sub-menus and
adjust the settings.
10 VOLUME + / –
Increases or decreases volume.
11 DVD buttons
Refer to section on “Functions of Remote
Control (DVD)”
12 TELETEXT
Allows to select teletext information.
(For detailed description of functions, refer
to section on “Using the Teletext”
13 SURF
Allows you to select up to a maximum of 10
channels and view quickly the selected channels.

12
FUNCTIONS OF REMOTE CONTROL (TV)
23
24
21
14
17
16
18
19
20
4
\
m
INCR. SURR.
PROG. LISTSURF
INCR. PIC
T/C AUDIO FTS ANGLE
Éá á
ç
Ç
àà
Å
22
15
25
14 STANDBY
–Switch set off temporarily to standby mode.
(The red light indicator lights up when set is
on standby mode).
– To switch on set from standby mode, press
Channel Up/Down, Digit (0 -9) or Standby
button.
15 CLOCK
Allows you display the clock on the screen.
16 44
44
4
Allows you to switch from Stereo to
Mono sound during stereo transmission
or to choose between language5or
language6during dual sound transmission.
17 SMART PICTURE
Allows you to select your desired picture
setting from 5 types of picture settings.
18 OK
Refer to section on “Functions of Remote
Control (DVD)
19 CURSOR RIGHT
Allows you to access the sub-menus and
adjust the settings.
20 CURSOR DOWN
Allows you to select the next item on the
menu.
21 CHANNEL + / –
Selects channel in ascending or descending
order.
22 MUTE
Mutes sound.To restore sound, press
button again.
23 PROGRAM LIST
Allows you to navigate through a list of
installed programs for a quick overview
of the channels and activate the channel
you have selected.
24 INCREDIBLE PICTURE
Allows you to view a more vivid and realistic
picture with better contrast when the “ON”
function is selected.
25 INCREDIBLE SURROUND
– Allows you to select Incredible Surround
sound when transmission is in stereo mode.
– Allows you to select Spatial Sound when
transmission is in mono mode.

13
4
\
m
INCR. SURR.
PROG. LISTSURF
INCR. PIC
T/C AUDIO FTS ANGLE
Éá á
ç
Ç
àà
Å
FUNCTIONS OF REMOTE CONTROL (DVD)
T/C (Title/Chapter)
Allows you to access
the title/chapter
selector mode.
AUDIO
Allows you to view the
different languages in the
menu bar.
ZOOM
Allows you to enlarge
the video image and
to pan through the
enlarged image.
OK
To confirm selection
on the menu.
ANGLE
Allows you to change
the camera angle.
MENU
Access menu of DVD.
TV/DVD Switch
TV mode or DVD mode
selector.
BACKWARD
Allows you to skip or
rewind.
FORWARD
Allows you to skip or
fast forward.
PAUSE
Allows you pause
playback temporarily.
PLAY
Allows you to activate
playback mode.
STOP
Allows you stop
playback mode.
EJECT
Allows you open/close
disc tray.
INCREDIBLE
SURROUND
Allows you select Stereo,
TruSurround 3D Virtual
Surround or Dolby Surround
compatible sound.
OSD
Access or exit On-Screen
display.

14
FUNCTIONS OF TV/DVD COMBI CONTROLS
Note
• You can enter the main menu by pressing both the Volume – and + buttons at the same
time.
• Press the Channel ¸or ˚button to select the next item on the menu.
• Press the Volume – or +button to access the sub-menus and adjust the settings.
1Mains Power button Switch mains power on or off.
2Standby Light indicator Indicate red light when standby mode is activated.
3Remote Sensor Acts as a sensor for activating the controls of the TV
when remote control handset is aimed at it.
4Volume – / + button Adjusts sound volume softer/louder.
5Channel ¸/˚button Selects channel in descending/ascending order.
6DVD Eject button Allows you to open/close DVD tray
EJECT
– VOLUME + ¸CHANNEL˚
INSTALL MENU
123456
DVD Tray
➠

15
SELECTING THE MENU LANGUAGE
AND AUTOMATIC TUNING OF CHANNELS
This section explains the operating instructions of theTV only.
Operating instructions are explained step by step to enable
you to operate the TV set easily. For instructions on operating
the DVD, refer to section on “Operating the DVD”
Before you tune in the channels by the Auto Store method, select the menu language of your
choice.
1. Enter main menu.
2. Press button repeatedly
until INSTALL is
selected.
3. Enter INSTALL menu.
Press button
Result on TV Screen
• PICTURE BRIGHTNESS
• SOUND COLOUR
• FEATURES CONTRAST
• INSTALL SHARPNESS
COLOUR TEMP
É
▼
• PICTURE LANGUAGE
• SOUND AUTO STORE
• FEATURES MANUAL STORE
• INSTALL SORT
CHANNEL EDIT
É
▲
INSTALL
LANGUAGE •ENGLISH
• AUTO STORE B.MELAYU
• MANUAL STORE
•SORT
•CHANNEL EDIT
Ñ
▲
É
▼
4
\
m
INCR. SURR.
PROG. LISTSURF
INCR. PIC
T/C AUDIO FTS ANGLE
É
á á
ç
Ç

16
OR
INSTALL
LANGUAGE • ENGLISH
• AUTO STORE B. MELAYU
• MANUAL STORE
• SORT
• CHANNEL EDIT
Ñ
▲
É
▼
INSTALL
• LANGUAGE
AUTO STORE • SEARCH
•MANUAL STORE
•SORT
•CHANNEL EDIT
•
Ñ
▲
É
▼
▲
▼
É
INSTALL
• LANGUAGE
• AUTO STORE •SEARCHING
• MANUAL STORE PLEASE WAIT
•SORT CHAN.FOUND 8
•CHANNEL EDIT 048.31 MHZ
•
INSTALL
• LANGUAGE
AUTO STORE • SEARCH
•MANUAL STORE
•SORT
•CHANNEL EDIT
•
Ñ
▲
É
▼
SELECTING THE MENU LANGUAGE
AND AUTOMATIC TUNING OF CHANNELS
4. Enter LANGUAGE mode.
5. Select desired language.
6. Exit from language mode.
7. Select AUTO STORE.
8. Start automatic tuning.
9. When tuning is completed,
exit menu from screen.
▲
É
▼
INSTALL
LANGUAGE •ENGLISH
•AUTO STORE
•MANUAL STORE
•SORT
•CHANNEL EDIT
•
Ñ
4
\
m
INCR. SURR.
PROG. LISTSURF
INCR. PIC
T/C AUDIO FTS ANGLE
É
á á
ç
Ç

17
MANUAL TUNING OF CHANNELS
Manual tuning allows you to store each programme manually.
1. Enter main menu.
2. Press button repeatedly
until INSTALL is
selected.
3. Enter INSTALL menu.
4. Press button repeatedly
until MANUAL STORE
is selected.
5. Enter MANUAL STORE
menu.
6. Select SEARCH.
7. Start manual tuning of
channel. Searching stops
once a transmitting
channel is found.
8. Select CHANNEL.
9. Key in the desired channel
number.
10. Select STORE.
11. Store tuned channel.
Note : If you want to
continue searching for
another transmitting
channel, repeat steps
7 to 11.
12. Exit menu from screen.
Press button
Result on TV Screen
• PICTURE LANGUAGE
• SOUND AUTO STORE
• FEATURES MANUAL STORE
• INSTALL SORT
CHANNEL EDIT
É
▲
INSTALL
• LANGUAGE COLOUR SYSTEM
• AUTO STORE SOUND SYSTEM
• MANUAL STORE SEARCH
• SORT CHANNEL
• CHANNEL EDIT STORE
•
▲
É
▼
▼
▲
Ñ
INSTALL
MANUAL STORE
•COLOUR SYSTEM
• SOUND SYSTEM
SEARCH •048.31MHZ
•CHANNEL
•STORE
É
▼
▲
Ñ
INSTALL
MANUAL STORE
•COLOUR SYSTEM
• SOUND SYSTEM
SEARCH •196.25MHZ
•CHANNEL
•STORE
É
▼
▲
Ñ
INSTALL
MANUAL STORE
•COLOUR SYSTEM
• SOUND SYSTEM
•SEARCH
CHANNEL •18
•STORE
É
▼
▲
Ñ
INSTALL
MANUAL STORE
•COLOUR SYSTEM
• SOUND SYSTEM
•SEARCH
•CHANNEL
STORE •STORED
É
▼
▲
Ñ
INSTALL
MANUAL STORE
•COLOUR SYSTEM
• SOUND SYSTEM
SEARCH •196.25MHZ
•CHANNEL
•STORE
É
4
\
m
INCR. SURR.
PROG. LISTSURF
INCR. PIC
T/C AUDIO FTS ANGLE
É
á á
ç
Ç

18
SELECTING THE COLOUR /SOUND SYSTEM
This feature allows you to select your desired COLOUR and SOUND system. If AUTO
is selected, the respective colour and sound system will be automatically selected according
to the transmission system.
Note : Select your desired colour and sound system manually if reception is poor at AUTO
mode.
Repeat step 1 to step 5 as in “MANUAL TUNING OF CHANNELS”
6. COLOUR SYSTEM is
selected. Enter COLOUR
SYSTEM mode.
7. Select the desired colour
system.
8. Exit from colour system
mode.
9. Proceed to select
SOUND SYSTEM.
10. Enter SOUND SYSTEM
mode.
11. Select the desired sound
system.
12. Exit from sound system
mode.
13. Press button repeatedly
until STORE is selected.
14. Store selected system.
15. Exit menu from screen.
Press button
Result on TV Screen
OR
▼
▲
É
Ñ
INSTALL
MANUAL STORE
S COLOUR SYSTEM • AUTO
• SOUND SYSTEM PAL
• SEARCH SECAM
•CHANNEL
•STORE
•
É
▼
▲
É
Ñ
INSTALL
MANUAL STORE
•COLOUR SYSTEM
SOUND SYSTEM •AUTO
•SEARCH B/G
•CHANNEL D/K
•STORE
•
É
▼
▲
É
Ñ
INSTALL
MANUAL STORE
• COLOUR SYSTEM
SOUND SYSTEM • AUTO
• SEARCH B/G
• CHANNEL D/K
• STORE
•
É
▼
▲
Ñ
INSTALL
MANUAL STORE
COLOUR SYSTEM
• SOUND SYSTEM
•SEARCH
•CHANNEL
STORE •
É
▼
▲
Ñ
INSTALL
MANUAL STORE
COLOUR SYSTEM
• SOUND SYSTEM
•SEARCH
•CHANNEL
STORE •STORED
É
▼
▲
Ñ
INSTALL
MANUAL STORE
•COLOUR SYSTEM
• SOUND SYSTEM
SEARCH •196.25MHZ
•CHANNEL
•STORE
É
4
\
m
INCR. SURR.
PROG. LISTSURF
INCR. PIC
T/C AUDIO FTS ANGLE
É
á á
ç
Ç

19
FINE TUNING OF CHANNELS
This feature allows you to adjust picture reception in areas of weak reception.
1. Enter main menu. 2. Select INSTALL. 3. Enter install menu.
4. Press button repeatedly
until MANUAL STORE
is selected.
5. Enter MANUAL STORE
menu.
6. Press button repeatedly until
FINE TUNE is selected.
7. Start fine-tuning until desired
picture and sound is obtained.
8. Select STORE.
9. Store last fine-tuned status.
10. Exit menu from screen.
Press button
Result on TV Screen
➠➠➠
INSTALL
• LANGUAGE COLOUR SYSTEM
• AUTO STORE SOUND SYSTEM
• MANUAL STORE SEARCH
• SORT CHANNEL
• CHANNEL EDIT STORE
•
▲
É
▼
OR
INSTALL
LANGUAGE •ENGLISH
•AUTO STORE B. MELAYU
•MANUAL STORE
•SORT
•CHANNEL EDIT
Ñ
▲
É
▼
▼
▼
▲
É
INSTALL
MANUAL STORE
COLOUR SYSTEM •AUTO
• SOUND SYSTEM PAL
• SEARCH SECAM
•CHANNEL
•STORE
Ñ
▼
▲
INSTALL
MANUAL STORE
• SOUND SYSTEM
• SEARCH
• CHANNEL
•STORE
FINE TUNE
ÑÉ
▼
▲
Ñ
INSTALL
MANUAL STORE
•COLOUR SYSTEM
• SOUND SYSTEM
•SEARCH
•CHANNEL
STORE •
É
▼
▲
Ñ
INSTALL
MANUAL STORE
• COLOUR SYSTEM
• SOUND SYSTEM
• SEARCH
•CHANNEL
STORE •STORED
É
▼
▲
Ñ
INSTALL
MANUAL STORE
•COLOUR SYSTEM
• SOUND SYSTEM
SEARCH •048.31MHZ
•CHANNEL
•STORE
É
4
\
m
INCR. SURR.
PROG. LISTSURF
INCR. PIC
T/C AUDIO FTS ANGLE
É
á á
ç
Ç

20
SORTING OF CHANNELS
This feature allows you to change the channel number to your choice for a particular TV
station.
1. Enter main menu. 2. Select INSTALL. 3. Enter install mode.
4. Press button repeatedly
until SORT is selected.
5. Enter SORT menu.
6. Key in the channel number
in the FROM column, that
is, the channel you want to
swap from.
7. Select TO .
8. Key in the channel number
in the TO column. that is,
the channel you want to
swap to.
9. Select EXCHANGE.
10. Activate exchange of
channels.
11. Exit menu from screen.
➠
Press button
Result on TV Screen
INSTALL
• LANGUAGE FROM
• AUTO STORE TO
• MANUAL STORE EXCHANGE
• SORT
• CHANNEL EDIT
▲
É
▼
▲
▼
É
INSTALL
SORT
FROM •8
• TO
• EXCHANGE
•
Ñ
▲
INSTALL
SORT
• FROM
TO •
• EXCHANGE
•
Ñ
É 6
▼
▲
INSTALL
SORT
•FROM
•TO
EXCHANGE •EXCHANGED
•
Ñ
É
▲
INSTALL
SORT
•FROM
•TO
EXCHANGE •
•
Ñ
É
INSTALL
LANGUAGE •ENGLISH
•AUTO STORE B. MELAYU
•MANUAL STORE
•SORT
•CHANNEL EDIT
Ñ
▲
É
▼
▼
➠➠
4
\
m
INCR. SURR.
PROG. LISTSURF
INCR. PIC
T/C AUDIO FTS ANGLE
É
á á
ç
Ç