
2TPS1.1L LA 1. Technical Specifications,Connections,and Chassis Overview
Index of this chapter:
1.1 Technical Specifications
1.2 Connections
1.3 Chassis Overview
Notes:
Figures below can deviate slightly from the actual situation,
due to the different set executions.
Specifications are indicative (subject to change)
1.Technical Specifications,Connections,and Chassis Overview
1.1 Technical Specifications
1.1.1 Technical Specifications
Type : LCD
Outline dimensions : 760.0 mm(H) x 450.0 mm(V) x 47.4(D)
mm (Typ.)
Pitch (mm) : 510.75 .um(H) x 170.25um(V)
Pixel format : 1366 horiz. by 768 vert. pixels
Color pixel arrangement : RGB vertical stripe
Display surface : Hard coating(3H),Anti-glare treatment
of the front polarizer
Number of color : 16,777,216 colors ( 8 bits)
Backlight : 16 CCFL
Active area (WxH) : 697.68mm X 392.26 mm
View angle : Viewing angle free(R/L 176(Typ.),U/D
176(Typ.))
Contrast ratio : Typical 1500 : 1
Luminance of white : 500 cd/m²(Center 1 points, Typ.)
1.1.2 Sound
Sound system : 2CS, NICAM B/G (5.5-5.85), NICAM D/K (6.5-5.85),
NICAM I (6.0-6.52), stereo for all (should be in line
with RF system of each region)
Maximum power:2X5
1.1.3 Miscellaneous
Power supply
AC-input : 90V ~ 264VAC,50/60±2Hz
Power consumption :
Normal:
1.PC Mode TYP 100 W[Smart picture as "Normal" ] (with audio)(26")
PC Mode TYP 145 W[Smart picture as "Normal" ] (with audio)(32")
2.TV Mode TYP 100 W [Smart picture as "Rich"] (with audio)(26")
TV Mode TYP 145 W [Smart picture as "Rich"] (with audio)(32")
Maximum: 130W (with audio)(26")
170W (with audio)(32")
Power cord length : 1.8M
Power cord type : 3 lead with earth plug , plugable
(US type)
Power indicator : LED (On: blue ,Sleeping mode: Amber )
Auto power saving : EPA, Nutek, VESA DPMS
Horizontal scan : 30 ~ 61KHz
Vertical scan : 56 ~ 75 Hz
Ambient conditions:
Ambient temperature: 15°C~35°C
Relative humidity : 25% ~ 75%.
Supported video formats: 720 X 480i 60Hz
720 X 576i 50Hz
720 X 480P 60Hz
720 X 576P 50Hz
1280X 720P 50Hz
1280X 720P 60Hz
1920X1080i 50Hz
1920X1080i 60Hz
1920X1080p 50Hz
1920X1080p 60Hz
1.2 Connections
1.2.1 Signal Connector
Connectors: From Right to Left
1.Tuner: PAL D/K IandNTSC-M
2.Compair Rx/Tx communicate
3.AV1 audio IN : AV1 and S-Video shared audio R/L(RCA jack)
4.AV1 IN : Composite video input (AV1)
5.CVI IN : Component input with YPbPr format with audio R/L.
6.PC audio IN: audio R/L(mini-jack).
7.PC IN: VGA input (D-SUB connectors)
8.DVI-D : digital PC and video input
9.Earphone : earphone jack
10.AV2 IN : Composite video input (AV2 side)
11.AV2 audio IN : AV2 and S-Video side audio R/L(RCA jack)
12.S-Video IN : S-video input (S-Video side)
9
10
11
12
1.2.2.1 signal type
PC Signal
Analog Video :15 pin D-Sub
0.7 Vp-p linear, positive polarity and
separate Sync ( TTL level, positive or
negative polarity )
Digital Video :24-pin DVI-D connect connector, Single
TMDS link according to DVI specification
Audio signal :Mini-jack audio input
TV Signal
1.2.2 Input Signal
RF signal : Aerial or cable via RF connector,
RF input level -10mV (80dBuV) typical, terminated with
input impedance of 75W.
Transient response: < 250 nS.
Sound (5.5MHz) suppression: > 55dB.
Chroma (4.43MHz) suppression: > 25dB.
Y/C separation: > 20dB.
Support:
PAL B/G INTSC-M
Component Y Pb Pr with RCA connector ( Video , Audio input )
Specification
Video Y:700mV, Pb,Pr,: ±350mV,
Impedance : 75W
Audio : L/R input
Nominal : 0.5 V rms.
Maximum : 1.5 V rms. Impedance > 10 kW
Note : the input will be overloaded
when the signal > 1.5 V rms.
Support: 480i/p, 720p/60Hz, 1080i/60Hz