Philips 43PFH4082/96 User manual

Published by Yingqun.Wen 4082 Quality Subject to modification
2017 ©TP Vision Netherlands B.V.
All rights reserved. Specifications are subject to change without notice. Trademarks are the
property of Koninklijke Philips Electronics N.V. or their respective owners.
TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust
earlier supplies accordingly.
PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Chassis name Platform Model name
4082 MSD3463 43PFH4082/96
4082
2017-Nov-25

Published by Yingqun.wen 4082 Quality Subject to modification
2017-July-19
2017 ©TP Vision Netherlands B.V.
All rights reserved. Specifications are subject to change without notice. Trademarks are the
property of Koninklijke Philips Electronics N.V. or their respective owners.
TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust
earlier supplies accordingly.
PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
1.Product inforamtion……….……………………………………………………………………………………3
2.Connections overview……..…..…..………………..…………………………………………………………6
3.Mechanical Instructions………………….…………………………………………………………………….7
Cable dressing (43" 4082 series)………………………………………………………………………………7
Assembly/Panel Removal ………………………………………………………………………………………7
4.Factory Modes…………….……………….………………….…………………………………………….….15
5. So ft wa re up gr ad in g an d Pa nel Cod e …… …… … .. . …… …… …… …………………… …… … .. 1 7
6.Circuit Descriptions…..……………………….………………………………………………………………19
7.IC Data Sheet……...……………………………………………………………………………………….…..25
8.Circuit Diagrams……………...……………………………………………………………………………….27
9.Styling Sheet……………….…………………….……………………………………………………………..35
4082 series 43"……………………………………………………………………………………………….35

3
1. Product information
Product information is subject to change without notice.
For detailed product information，please visit www.philips.com/support
Display Type
Diagonal screen size
• 43PFH4082/96: 42.51 inch
Display resolution
• 43PFH4082/96 : 1920*1080p
Input resolution
• 800 x 600p - 60 Hz
• 1024 x 768p - 60 Hz
• 1280 x 768p - 60 Hz
• 1360 x 765p - 60 Hz
• 1360 x 768p - 60 Hz
• 1280 x 1024p - 60 Hz
• 1920 x 1080p - 60 Hz23.5
Video formats Resolution — Refresh rate
• 480i, 480p,576i, 576p,720p,1080i,1080p(24/25/30/50/60Hz)
Computer formats Resolutions (amongst others)
720*400@70HZ
640*480@60HZ
800*600@60HZ
1024*768@60HZ
1360*768@60HZ
1280*720@60HZ
1280*960@60HZ
1280*1024@60HZ
1600*900@60HZ
1920*1080@60HZ
Dimensions and Weights
43PFH4082/96
• without TV stand:
Width 969mm - Height 578 mm - Depth 83mm - Weight 7.4kg
• with TV stand:
Width 969 mm - Height 625mm - Depth 226mm - Weight 7.5kg
Connectivity
I/O port to be clearly indicated
TV*2/USB*2/VGA*1
/HDMI*3/YPBPR&AV-IN*1/Earphone
*1/Coaxial-OUT*1/PC audio*1/Audio
in*1
Playback YES
Component (HD/SD)@24p/50/60 (HD/SD)@24p/50/60
HDMI Number 3
HDMI 1 HDMI 1.4 /up to 2k@60hz
4：4：4 down
HDMI 2 HDMI 1.4 /up to 2k@60hz
4：4：4 down
HDMI 3 HDMI 1.4 /up to 2k@60hz
4：4：4 down
HDMI 4 NA
HDCP v2.2 (on HDMI 2.0 port) YES
HDMI ARC HDMI-3

4
PC input (VGA) VGA
AV （input）YES
Headphone YES
Video and Audio out NA
Digital audio out (SPDIF)
co-axial/Optical Co-axial Out
RJ45 NA
DLNA/ Certification NA
WiFi NA
EasyLink (HDMI-CEC) YES
Antenna Tuner /Satellite tuner Antenna Tuner(down)
Wireless connections N/A
Wi-Fi Band Concurrent N/A
Bluetooth for subwoofer/RC (do not claim
commercially)
N/A
MHL(Version ) HDMI-1
Sound
Mono/Stereo/Virtual Surround Mono/Stereo/Virtual Surround
Output Power (10% THD) RMS (RMS Watts) 16W
Speaker configuration 8W+8W
Speaker system (Number of on board Speakers ) 2.0
Speaker type built-in(normal)
Auto Volume Levelier / Auto Volume Levelier + N/A
Dolby Digital DecoderType(DD/DD+) N/A
DTS Studio Sound N/A
DTS 2.0+ Digital out N/A
SPL (>= 84dB @ 2m) 78dB @ 2m
Acoustic frequence range 160~8K HZ<=16dB
Multimedia
Video Playback Formats MPEG-1/MPEG-2/MPEG-4 H.264
FLV/RV8/RV9/RV10
Subtitles Formats Support SRT、ASS
Music Playback Formats MP3，AAC
Picture Playback Formats JPG、JPEG、BMP、PNG
Pause TV/USB recording (PVR) YES
Time shift YES
PIP/POP NA
USB USB2.0(*2)
USB Harddisk Format (Power) FAT/NTFS (500mA)

5
Power
Product specifications are subject to change without
notice. For more specification details of this product,
see www.philips.com/support
Power
• Mains power : AC 100-240V 50/60Hz
• Standby Energy Consumption:≤0.5W
• Ambient temperature : 5°C to 40°C

6
2. Connections Overview

7
3. Mechanical Instructions
3.1 Cable Dressing
Serial no part description function
1 Backlight wire Connect to PJ2
2 Power wire Connect to PCN105
3 LVDS wire Cn401 to T-CON board
4 Speaker wire CN203 to speaker (yellow black wire)
5 Speaker wire CN201 to speaker (red black wire)
6 two-terminal wire CN104 to IR board
7 two-terminal wire IR Board to key board
3.2 Assembly/Panel Removal
3.2.1 Stand removal1. Remove the fixation screws [1] that secure the stand
2. Take the stand bracket out from the set.
3.2.2 Disassemble Back Cover-1
1. Use electric screwdriver to dismantle 7PCS Ф3×6mm screws from back cover. Figure 1
2. Put removed screws at appointed material box.Do not mix it with others material
3. After self-check OK,flow it into next station by foot switch.
11
1
1

8
3.2.3 Disassemble Back Cover-2
1. Take off screws with electric screwdriver. Figure 1
2. Categorize and place removed screws at the appointed material box. Do not mix with other material.
3. Both hands respectively grasp the middle of left and right sides of back cover-M,lift the right side of back cover to separate the
buckle on lower right side of back cover-M,from back cover-L.Then Pushing back cover-M toward right and up to make the
buckle on the lower left side of back cover-M separate from back cover-R. Take out power cord from the slot and then take
down back cover-M and put it on the mat of circulated cart. Figure 2
4. After self-check OK,flow it into next station by foot switch.

9
3.2.4 Disassemble Wire
1. Use diagonal pliers to cut off 2pcs cable ties from the baffle and place them at appointed position. Figure 1
2. As figure show,tear off fabric tapes from wires and place them at appointed position. Figure 1
3. As Figure show,tear off aluminum foil from FFC wire and place them at appointed position. Figure 1
4. Unplug all wire terminals from motherboard connector. Figure 1
5. Unplug rocker power switch and power cord from the slot of back cover. Figure1/A
6. Take down power cord and LVDS wire,categorize and place them at appointed position orderly
Figure 2

10
3.2.5 Dismantle left/right back cover
1. Use electric screwdriver to dismantle 2pcs Ф3×6mm screws from back cover. Figure 1
2. Place removed screws at the appointed material box. Do not mix with other material
3. Take down back cover-L and back cover-R respectively,and place them at appointed position.
4. After self-check OK,flow it into next station by foot switch.
.

11
3.2.6 Dismantle speaker & key module
1. Unplug speaker's wire from the buckle of back cover-L,as Figure1 show. Then take down speaker from its plastic pillar. Figure 1
2. Unplug speaker's wire from back cover-R by the same way. Figure 1
3. Press the key bracket buckle outward to make it separate from back cover's slot.Then pull out key bracket. Figure 2
4. Categorize and place removed speaker at appointed position orderly.
5. Place removed key module,back cover-L,back cover-R at the appointed position orderly.
3.2.7 Dismantle keypad module
1. Use electric screwdriver to dismantle 2pcs Φ3×5mm screws from keypad. Figure 1
2. Place removed screws at the appointed material box. Do not mix with other material.
3. Place removed key bracket at the appointed position orderly.
4. Unplug double terminal wire from keypad connector. Figure 2
5. Place removed keypad and wire at the appointed position orderly.

12
3.2.8 Dismantle IO baffle
1. Use electric screwdriver to dismantle 4pcs Ф3×3mm screws from IO baffle. Figure 2
2. Put removed screws in the material box. Do not mix with other materials.
3. Take down IO baffle from right side and lower side,and place them at appointed position orderly.
4. After self-check OK,flow it into next station by foot switch.
3.2.9 Dismantle motherboard
1. Use electric screwdriver to dismantle 4PCS M3×7mm screws from motherboard. Figure 2.
2. Put removed screws in the material box. Do not mix with other materials.
3. Place motherboard on the ESD tray.
4. After self-check OK,flow it into next station by foot switch.
3.2.10 Dismantle base support
1. Use electric screwdriver to dismantle 8pcs Φ4×6mm screws from base support. Figure 1
2. Put removed screws in the material box. Do not mix with other materials.
3. Put removed base support at the appointed position orderly

13
3.2.11 Dismantle lower bracket
1. Use electric screwdriver to dismantle 7pcs Ф3×3mm screws from lower bracket. Figure 1
2. Put removed screws in the material box. Do not mix with other materials.
3. Take down lower hardware and hardware bracket,put them at appointed position orderly.
3.2.12 Dismantle mylar film and hexagonal screw
1. Tear off mylar film from back plate,as figure show. Figure 1/A

14
2. Tear off mylar film and put it at appointed position.
3. Use electric screwdriver to dismantle 4pcs hexagonal screws from back plate,as figure show. Figure 2/A
3.2.13 LCD Panel
1. Remove the SSB as described earlier.
2. Remove the PSU as described earlier.
3. Remove the keyboard control panel as described earlier.
4. Remove the stand bracket as described earlier.
5. Remove the IR/LED as described earlier.
6. Remove the fixations screws that fix the metal clamps to the front bezel. Take out those clamps.
7. Remove all other metal parts not belonging to the panel.
8. Lift the LCD Panel from the bezel.
When defective, replace the whole unit.

15
4. Factory Mode
Purpose
Press the following key sequence on a standard RC transmitter: “1999” directly followed by MENU,
To perform extended alignments.
Primary menu Secondary menu Value,remark
ADC ADJUST
MDOE VGA/YPBPR(SD)/YPBPR(HD)
,Selection
R-GAIN
Front-end gain adjustment
G-GAIN
B-GAIN
R-OFFSET
Clamp level adjustment
G-OFFSET
B-OFFSET
AUTO ADC ADC automaticall
y
ad
j
ust
PICTURE MODE
MODE VGA/HDMI1/HDMI2/HDMI3/
DTV/ATV/AV/YPBPR
PICTURE MODE D
y
namic/Standard/Sotf/User
BRIGHTNESS BRIGHTNESS
CONTRAST CONTRAST
COLOR COLOR
SHARPNESS SHARPNESS
TINT TINT
Co
py
all No function
W/B ADJUST
Source VGA/HDMI1/HDMI2/HDMI3/
DTV/ATV/AV/YPBPR
TEMPERATURE Cool, Standard, Warm
R-GAIN
White level adjustment
G-GAIN
B-GAIN
R-OFFSET
Black level adjustment
G-OFFSET
B-OFFSET
Co
py
all No function
SSC
MIU Enable DDR spectrum enable
MIU0 S
p
an Exhibition fre
q
uentl
y
wide
MIU Ste
p
S
p
read s
p
ectrum ste
p
LVDS enable LVDS s
p
ectrum enable
LVDS S
p
an Exhibition fre
q
uentl
y
wide
LVDS Ste
p
S
p
read s
p
ectrum ste
p
LVDS swin
g
LVDS swin
g
Spectial set
2HOUR OFF 2hours
p
ower off enable
WDT on/off
WHITE PATTER OFF/White/Red/Green/Blue/Bla
ck/192Grey
GE/GOP PATTERN
BMAP PATTERN
Restore user default Factory reset
PVR_RECORD ALL PVR Record on/off
Power on/off/Mem
Mirror Enable Mirror Enable enable
Ageing mode Ageing mode enable
Auto Volume on/off
PVR Encrypt on/off
Qmap adjsut PQ setting
PEQ PEQsetting
other
Test pattern
UART DEBUG DEBUG ON/OFF
HDMI CEC/ARC CEC/ARC ON/OFF

16
Backlight Adjust backlight
OverScan
Overscan
_
resolution Reselution select
Overscan
_
hsize Ad
j
ust overscan H size
Overscan
_
h
p
osition Ad
j
ust overscan H
p
osition
Overscan
_
vsize Ad
j
ust overscan V size
Overscan
_
v
p
osition Ad
j
ust overscal V
p
osition
HDCPKe
y
usb u
pg
rade HDCPKe
y
usb u
pg
rade
SW information SW information
Non-linear
MODE Feature Selection
OSD 0
Curve adjustment
OSD 25
OSD 50
OSD 75
OSD 100
Channel table1 KTC factor
y
Fre
q
uec
y
table set
Channel table2 KTC factor
y
Fre
q
uec
y
table set
Channel dvbt KTC factory Frequecy table set

17
5. Software Upgrading and Panel Code
5.1 Software Upgrading
Operations and procedure of software upgrading:
1). Changed the file name to "MERGE.bin", then stored software in the FAT32 format blank U disk.
2). Insert USB flash disk into the USB upgrade port, upgrade the software according to the following the operating instructions:
Select AIR or DTV signal source, press Menu key to pop up the main menu, then choose.
Select CHANNEL, press right key or OK key to enter.

18
Select Software Update(USB), press right key or OK key to enter.
Software update menu will pop up when press confirm key, then select “Yes” to confirm:
The process of software updating:
Method 2：Keep pressing VOL+ and CH+ keys on the machine panel, power on the machine, the standby light flashes quickly after
about 5 seconds, standby light extinguish and turn into lighting after about a minute, means that the upgrade is completed.
5.1.4 Notice：
①. When the machine Upgrading (U disk light flash), do not remove U disk or switch off the power, otherwise it will
destroy the software and lead can not upgrade.
②. The machine must be power off when inserted or pulled out U disk, to avoid U disk or damage the machine.
5.2 Panel Code
Press the following key sequence on a standard RC transmitter: “1999” directly followed by MENU, can see the panel type
information from factory menu, see the Panel PN from the configuration table
CTN
_
ALT BOM# Panel T
yp
e Panel PN
43PFH4082/96 K430WDK3-LA260A4 7422-430LGK-385AK041-F

19
6. Circuit Descriptions
6.1 Introduction
The 4082 is covered by MSD3463 platform. The major deltas versus its predecessor support DVB-T, with also multi-media, Video out
The 4082 chassis comes with the following stylings:
Series 4082 43PFH4082/96
6.1.1 Implementation
Key components of this chassis are:
TUNER POWER AS1117
VDDC POWER
MSD3463GSA-Z1 T8C2
DDR POWER 1.5V
3.3V STANDBY AS1117
64 Mbit SPI FLASH
HDMI1 ARC
HDMI2 PORT
HDMI3 MHL
6.1.2 Block diagram

20
6.2 Power Supply
Power architecture of this platform.
6.2.1 Power Supply Unit
All power supplies are a black box for Service. When defective, a new board must be ordered and the defective one must be returned,
unless the main fuse of the board is broken. Always replace a defective fuse with one with the correct specifications! This part is available
in the regular market.
Consult the Philips Service web portal for the order codes of the boards.
Important delta’s with the platform are:
• New power architecture for LED backlight
• “Boost”-signal is now a PWM-signal + continuous variable
The control signals are:
• PS-ON
• Lamp “on/off”
• DIM (PWM) (not for PSDL)
In this manual, no detailed information is available because of design protection issues.
• +12 output (on-mode)
• +12V_audio (audio AMP power)
• Output to the display; in case of
- IPB: High voltage to the LCD panel
- PSL and PSLS (LED-driver outputs)
- PSDL (high frequent) AC-current.
6.2.2 Diversity
The diversity in power supply units is mainly determined by the diversity in displays.
The following displays can be distinguished:
• CCFL/EEFL backlight: power panel is conventional IPB
• LED backlight:
- side-view LED without scanning: PSL power panel
- side-view LED with scanning: PSLS power panel
- direct-view LED without 2D-dimming: PSL power panel
- direct-view LED with 2D-dimming: PSDL power panel.
PSL stands for Power Supply with integrated LED-drivers.
PSLS stands for a Power Supply with integrated LED-drivers with added Scanning functionality (added microcontroller).
PSDL stands for a Power Supply for Direct-view LED backlight with 2D-dimming.