Philips PTV800 User manual

IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all Philips
Consumer Electronics Company** Equipment. The service procedures recommended by
Philips and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed
for the purpose. The special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES
which should be carefully read in order to minimize the risk of personal injury to service
personnel. The possibility exists that improper service methods may damage the
equipment. It also is important to understand that these CAUTIONS and NOTICES
ARE NOT EXHAUSTIVE. Philips could not possibly know, evaluate and advise the
service trade of all conceivable ways in which service might be done, or of the possible
hazardous consequences of each way. Consequently, Philips has not undertaken any such
broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is
not recommended by Philips must first satisfy himself thoroughly that neither his safety
nor the safe operation of the equipment will be jeopardized by the service method
selected.
** Hereafter throughout this manual, Philips Consumer Electronics Company will be
referred to as Philips.
WARNING
Critical components having special safety characteristics are identified with a or
"S" by the Ref. No. in the parts list and enclosed within a broken line* (where
several critical components are grouped in one area) along with the safety symbol
on the schematics or exploded views. Use of substitute replacement parts which
do not have the same specified safety characteristics may create shock, fire, or other
hazards. Under no circumstances should the original design be modified or altered
without written permission from Philips. Philips assumes no liability, express or
implied, arising out of any unauthorized modification of design. Servicer assumes all
liability.
* Broken Line ____ _ ____ _ ____ _ ____

FIRE AND SHOCK HAZARD
1.Be sure all components are positioned in such a way as to avoid the possibility of adjacent component
shorts. This is especially important on those chassis which are transported to and from the service shop.
2.Never release a repaired unit unless all protective devices such as insulators, barriers, covers, strain
reliefs, and other hardware have been installed in accordance with the original design.
3.Soldering and wiring must be inspected to locate possible cold solder joints, solder splashes, sharp solder
points, frayed leads, pinched leads, or damaged insulation (including the ac cord). Be certain to remove
loose solder balls and all other loose foreign particles.
4.Check across-the-line components and other components for physical evidence of damage or
deterioration and replace if necessary. Follow original layout, lead length, and dress.
5.No lead or component should touch a receiving tube or a resistor rated at 1 watt or more. Lead tension
around protruding metal surfaces or edges must be avoided.
6.Critical components having special safety characteristics are identified with an 'S' by the Ref. No. in the
parts list and enclosed within a broken line* (where several critical components are grouped in one area)
along with the safety symbol on the schematic diagrams and /or exploded views.
7.When servicing any unit, always use a separate isolation transformer for the chassis. Failure to use a
separate isolation transformer may expose you to possible shock hazard, and may cause damage to
servicing instruments.
8.Many electronic products use a polarized ac line cord (one wide pin on the plug). Defeating this safety
feature may create a potential hazard to the servicer and the user. Extension cords which do not
incorporate the polarizing feature should never be used.
9.After reassembly of the unit, always perform an ac leakage test or resistance test from the line cord to all
exposed metal parts of the cabinet. Also, check all metal control shafts (with knobs removed), antenna
terminals, handles, screws, etc., to be sure the unit may be safely operated without danger of electrical
shock.
* Broken line ____ _ ____ _ ____ _ ____

LEAKAGE CURRENT COLD CHECK
1.Unplug the ac line cord and connect a jumper between the two prongs of the plug.
2.Turn on the power switch.
3.Measure the resistance value between the jumpered ac plug and all exposed cabinet parts of the receiver,
such as screw heads, antennas, and control shafts. When the exposed metallic part has a return path to the
chassis, the reading should be between 1 megohm and 5.2 megohms. When the exposed metal does not
have a return path to the chassis, the reading must be infinity. Remove the jumper from the ac line cord.
LEAKAGE CURRENT HOT CHECK
1.Do not use an isolation transformer for this test. Plug the completely reassembled receiver directly into
the ac outlet.
2.Connect a 1.5k, 10W resistor paralleled by a 0.15uF. capacitor between each exposed metallic cabinet
part and a good earth ground such as a water pipe, as shown below.
3.Use an ac voltmeter with at least 5000 ohms/volt sensitivity to measure the potential across the resistor.
4.The potential at any point should not exceed 0.75 volts. A leakage current tester may be used to make
this test; leakage current must not exceed 0.5mA. If a measurement is outside of the specified limits,
there is a possibility of shock hazard. The receiver should be repaired and rechecked before returning it
to the customer.
5.Repeat the above procedure with the ac plug reversed. (Note: An ac adapter is necessary when a
polarized plug is used. Do not defeat the polarizing feature of the plug.)
OR
With the instrument completely reassembled, plug the ac line cord directly into a 120Vac outlet. (Do not
use an isolation transformer during this test.) Use a leakage current tester or a metering system that
complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and
Underwriters Laboratories (UL) 1410, (50.7). With the instrument ac switch first in the on position and
then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed
metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays,
control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis.
Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the outlet and
repeat the test. See the graphic below.

TV SAFETY NOTES
SAFETY CHECKS
After the original service problem has been corrected, a complete safety check should be made. Be sure to
check over the entire set, not just the areas where you have worked. Some previous servicer may have left
an unsafe condition, which could be unknowingly passed on to your customer. Be sure to check all of the
following:
Fire and Shock Hazard
Implosion
X-Radiation
Leakage Current Cold Check
Leakage Current Hot Check
Picture Tube Replacement
Parts Replacement
WARNING: Before removing the CRT anode cap, turn the unit OFF and short the HIGH VOLTAGE to
the CRT DAG ground.
SERVICE NOTE: The CRT DAG is not at chassis ground.
IMPLOSION
1.All picture tubes used in current model receivers are equipped with an integral implosion system.
Care should always be used, and safety glasses worn, whenever handling any picture tube. Avoid
scratching or otherwise damaging the picture tube during installation.
2.Use only replacement tubes specified by the manufacturer.
X-RADIATION
1.Be sure procedures and instructions to all your service personnel cover the subject of X-radiation.
Potential sources of X-rays in TV receivers are the picture tube and the high voltage circuits. The
basic precaution which must be exercised is to keep the high voltage at the factory recommended
level.
2.To avoid possible exposure to X-radiation and electrical shock, only the manufacturer's specified
anode connectors must be used.
3.It is essential that the service technician has an accurate HV meter available at all times. The
calibration of this meter should be checked periodically against a reference standard.
4.When the HV circuitry is operating properly there is no possibility of an X-radiation problem. High
voltage should always be kept at the manufacturer's rated value -no higher -for optimum
performance. Every time a color set is serviced, the brightness should be run up and down while
monitoring the HV with a meter to be certain that the HV is regulated correctly and does not exceed
the specified value. We suggest that you and your technicians review test procedures so that HV and
HV regulation are always checked as a standard servicing procedure, and the reason for this prudent
routine is clearly understood by everyone. It is important to use an accurate and reliable HV meter. It
is recommended that the HV reading be recorded on each customer's invoice, which will
demonstrate a proper concern for the customer's safety.

5.When troubleshooting and making test measurements in a receiver with a problem of excessive high
voltage, reduce the line voltage by means of a Variac to bring the HV into acceptable limits while
troubleshooting. Do not operate the chassis longer than necessary to locate the cause of the excessive
HV.
6.New picture tubes are specifically designed to withstand higher operating voltages without creating
undesirable X-radiation. It is strongly recommended that any shop test fixture which is to be used
with the new higher voltage chassis be equipped with one of the new type tubes designed for this
service. Addition of a permanently connected HV meter to the shop test fixture is advisable. The
CRT types used in these new sets should never be replaced with any other types, as this may result in
excessive X-radiation.
7.It is essential to use the specified picture tube to avoid a possible X-radiation problem.
8.Most TV receivers contain some type of emergency "Hold Down" circuit to prevent HV from rising
to excessive levels in the presence of a failure mode. These various circuits should be understood by
all technicians servicing them, especially since many hold down circuits are inoperative as long as
the receiver performs normally.
PICTURE TUBE REPLACEMENT
The primary source of X-radiation in this television receiver is the picture tube. The picture tube
utilized in this chassis is specially constructed to limit X-radiation emissions. For continued X-
radiation protection, the replacement tube must be the same type as the original, including suffix letter,
or a Philips approved type.
PARTS REPLACEMENT
Many electrical and mechanical parts in Philips television sets have special safety related
characteristics. These characteristics are often not evident from visual inspection nor can the protection
afforded by them necessarily be obtained by using replacement components rated for higher voltage,
wattage, etc. The use of a substitute part which does not have the same safety characteristics as the
Philips recommended replacement part shown in this service manual may create shock, fire, or other
hazards.
PRODUCT SAFETY GUIDELINES FOR ALL PRODUCTS
CAUTION: Do not modify any circuit. Service work should be performed only after you are thoroughly
familiar with all of the following safety checks. Risk of potential hazards and injury to the user increases if
safety checks are not adhered to.
USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.

PREVENTION OF ELECTROSTATIC DISCHARGE (ESD)
Some semiconductor solid state devices can be damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive (ES) Devices, Examples of typical ES devices are
integrated circuits and some field-effect transistors and semiconductor "chip" components. The following
techniques should be used to help reduce the incidence of component damage caused by electrostatic
discharge (ESD).
1.Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain
off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging ESD wrist strap, which should be removed for potential shock
reasons prior to applying power to the unit under test.
2.After removing an electrical assembly equipped with ES devices, place the assembly on a conductive
surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3.Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4.Use only an anti-static solder removal device. Some solder removal devices not classified as "antistatic
(ESD protected)" can generate an electrical charge sufficient to damage ES devices.
5.Do not use Freon propelled chemicals. These can generate electrical charges sufficient to damage ES
devices.
6.Do not remove a replacement ES device from its protective package until immediately before you are
ready to install it (most replacement ES devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive material).
7.Immediately before removing the protective material from the leads of a replacement ES device, touch
the protective material to the chassis or circuit assembly into which the device will be installed.
CAUTION: Be sure no power is applied to the chassis or circuit and observe all other safety precautions.
8.Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless
motion such as the brushing together of your clothes fabric or the lifting of your feet from a carpeted
floor can generate static electricity (ESD) sufficient to damage an ES device.)
NOTE to CATV system Installer:
This reminder is provided to call the CATV system installer's attention to article 820-22 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as practical.

PRACTICAL SERVICE PRECAUTIONS
IT MAKES SENSE TO AVOID EXPOSURE TO ELECTRICAL SHOCK. While some sources are
expected to have a possible dangerous impact, others of quite high potential are of limited current and are
sometimes held in less regard.
ALWAYS RESPECT VOLTAGES. While some may not be dangerous in themselves, they can cause
unexpected reactions –reactions that are best avoided. Before reaching into the powered color TV set, it is
best to test the high voltage insulation. It is easy to do, and is just a good service precaution.
BEFORE POWERING UP THE TV WITH THE BACK OFF (or on a test fixture), attach a clip lead to
the CRT DAG ground and to a screwdriver blade that has a well insulated handle. After the TV is powered
on and high voltage has developed, probe the anode lead with the blade, starting at the bottom of the High
Voltage Transformer (flyback –IFT). Move the blade to within two inches of the connector of the CRT. IF
THERE IS AN ARC, YOU FOUND IT THE EASY WAY, WITHOUT GETTING A SHOCK! If
there is an arc to the screwdriver blade, replace the High Voltage Transformer or the lead, (if removable)
whichever is causing the problem.
PICTURE TUBE REPLACEMENT PROCEDURE
Note: a. Two (2) people are required to handle this picture tube.
b. Safety Glasses must be worn during this procedure or whenever directly handling a picture tube.
c. Take care in each step not to damage the CRT or the cabinet.
1.Remove the Chassis and the CRT Socket Board Module from the cabinet.
2.A furniture pad or blanket should be positioned on the floor to support only the CRT Face. This pad or
blanket should be high enough to keep the CRT Face approximately 12 to 14 inches off the floor.
3.Using two people, place the cabinet in a front down position with the CRT Face on the pad or blanket.
4.Place padded blocks under each corner of the cabinet to keep it from rocking.
5.Remove the four screws, at the corners of the CRT.
6.With two people lowering the cabinet to the floor, leave the CRT elevated by the pad or blanket.
Note: Take care not to grasp the neck of the CRT during this procedure, as it is extremely fragile.
7.Two (2) people may then lift the CRT from the cabinet.
8.Remove the degaussing coil from the defective CRT and mount on the replacement. Take care to
maintain the exact shape and fit.
To install the new CRT, reverse steps 1 to 7.

GENERAL INFORMATION
CAUTION: A SEPARATE ISOLATION TRANSFORMER MUST BE USED WHEN
SERVICING THIS CHASSIS.
PTV 800 PANEL INFORMATION
Models Covered in This Manual:
Model Chassis
Reference Screen Size and Brand
1152980001 PTV800 52" Philips/Magnavox
626-54538.890 PTV800 52" Sears
8P4831C101 PTV805 48" Philips/Magnavox
8P4834C101 PTV805 48" Philips/Magnavox
8P5431C101 PTV805 54" Philips/Magnavox
8P5434C101 PTV805 54" Philips/Magnavox
8P6031C101 PTV805 60" Philips/Magnavox
8P6034C101 PTV805 60" Philips/Magnavox
8P4841C101 PTV810 48" Philips/Magnavox
8P4844C101 PTV810 48" Philips/Magnavox
8P5441C101 PTV810 54" Philips/Magnavox
8P5444C101 PTV810 54" Philips/Magnavox
8P6041C101 PTV810 60" Philips/Magnavox
8P6044C101 PTV810 60" Philips/Magnavox
8P6051C101 PTV810 60" Philips/Magnavox
48PP72A001 PTV811 48" Philips Brazil
48XP43C101 PTV811 48" Philips Taiwan/Latam
48XP44C101 PTV811 48" Philips Korea
54PP72A001 PTV811 54" Philips Brazil
54XP43C101 PTV811 54" Philips Taiwan/Latam
54XP44C101 PTV811 54" Philips Korea
60XP43C101 PTV811 60" Philips Mexico/Latam
MX5472C101 PTV815 54" Magnavox
MX6072C101 PTV815 60" Magnavox
MX6472C101 PTV815 64" Magnavox
XV5270B103 PTV820 52" Marantz Wallvision
PV5470C104/105 PTV825 54" Marantz
PV6070C104/105 PTV825 60" Marantz

MODEL TO PANEL LIST
•The Model to Panel List shown below identifies all electrical panels, modules, and
assemblies used in each model produced with the PTV800 series chassis.
•This information was current at time of printing.
•Information concerning cabinet parts and cabinet mounted parts (CRT/Yoke/etc.) is shown
in the Cabinet Replacement Parts List.
•Replacement part numbers for each panel are provided in the Chassis / Panel Replacement
Parts List.
•If you are attempting to service a model equipped with the PTV800 series chassis, the
necessary electrical information should be covered in the this service manual, even if the
corresponding model number is not listed.
PTV800
1152980001 52" Philips/Magnavox
5545380002 52" Sears
Reference Description
00APD019A001 Large Signal Panel
00ASG051A001 Small Signal Panel
00A10688A001 Digital Convergence Panel
00APT191A001 Green CRT Panel
00APT192A001 Red CRT Panel
00APT193A001 Blue CRT Panel
00ATC669A001 Customer Control Assembly
00ARR023A001 IR Receiver Panel
00ASW129A001 Switch Panel
00T207NGPM01 Remote Transmitter (1152980001)
00T206NGGA01 Remote Transmitter (5545380002)

PTV805
8P4831C101 48" Philips/Magnavox
8P4834C101 48" Philips/Magnavox
8P5431C101 54" Philips/Magnavox
8P5434C101 54" Philips/Magnavox
8P6031C101 60" Philips/Magnavox
8P6034C101 60" Philips/Magnavox
Reference Description
00APD019A001 Large Signal Panel
00ASG052A001 Small Signal Panel
00A10688A001 Digital Convergence Panel
00APT191A001 Green CRT Panel
00APT192A001 Red CRT Panel
00APT193A001 Blue CRT Panel
00ATC669A001 Customer Control Assembly
00ARR023A001 IR Receiver Panel
00ASW129A001 Switch Panel
00Y147SBAA01 Remote Transmitter UR714
PTV810
8P4841C101 48" Philips/Magnavox
8P4844C101 48" Philips/Magnavox
8P5441C101 54" Philips/Magnavox
8P5444C101 54" Philips/Magnavox
8P6041C101 60" Philips/Magnavox
8P6044C101 60" Philips/Magnavox
8P6051C101 60" Philips/Magnavox
Reference Description
00APD020A001 Large Signal Panel
00ASG053A001 Small Signal Panel
00A10688A001 Digital Convergence Panel
00APT191A001 Green CRT Panel
00APT192A001 Red CRT Panel
00APT193A001 Blue CRT Panel
00ATC669A001 Customer Control Assembly
00ARR023A001 IR Receiver Panel
00ASW129A001 Switch Panel
00AVJ221A001 Front Jack Panel
00A10707A001 2 Tube Scan Velocity Module
00Y147MEAA01 Remote Transmitter

PTV811
48PP72A001 48" Philips Brazil
48XP43C101 48" Philips Taiwan/Latam
48XP44C101 48" Philips Korea
54PP72A001 54" Philips Brazil
54XP43C101 54" Philips Taiwan/Latam
54XP44C101 54" Philips Korea
60XP43C101 60" Philips Mexico/Latam
Reference Description
00APD021A001 Large Signal Panel
00ASG053A001 Small Signal Panel
00A10688A001 Digital Convergence Panel
00APT191A001 Green CRT Panel
00APT192A001 Red CRT Panel
00APT193A001 Blue CRT Panel
00ATC669A001 Customer Control Assembly
00ATC669SKD1 Customer Control Assembly
(48PP72A001 and 54PP72A001)
00ARR023A001 IR Receiver Panel
00ASW129A001 Switch Panel
00AVJ221A001 Front Jack Panel
00AMP030A001 25W Audio Amp
00A10690A001 3 Tube Scan Velocity Module
00H147MEAA01 Remote Transmitter UR614

PTV815
MX5472C101 54" Magnavox
MX6072C101 60" Magnavox
MX6472C101 64" Magnavox
Reference Description
00APD020A001 Large Signal Panel
00ASG054A001 Small Signal Panel
00A10688A001 Digital Convergence Panel
00APT191A001 Green CRT Panel
00APT192A001 Red CRT Panel
00APT193A001 Blue CRT Panel
00ATC669A001 Customer Control Assembly
00ARR023A001 IR Receiver Panel
00ASW129A001 Switch Panel
00AVJ218A001 Front Jack Panel
00AMP029A001 25W Audio Amp
00A10691A001 Stereo Spread Panel
00A10672C003 Guide Plus Panel
00A10706A001 Remote Locator
00A10694A001 Wallvision Switch Panel
00A10690A001 3 Tube Scan Velocity Module
00X177CEAA01 Remote Transmitter UR617
PTV820
XV5270B103 52" Marantz Wallvision
Reference Description
00APD020A001 Large Signal Panel
00ASG056A001 Small Signal Panel
00A10688A001Digital Convergence Panel
00APT191A001 Green CRT Panel
00APT192A001 Red CRT Panel
00APT193A001 Blue CRT Panel
00ATC670A001 Customer Control Assembly
00ARR024A001 IR Receiver Panel
00ASW131A001 Switch Panel
00AMP029A001 25W Audio Amp
00A10691A001 Stereo Spread Panel
00A10672C003 Guide Plus Panel
00A10695A001 Wallvision Switch Panel
00Z147CEAA01 Remote Transmitter UR614

PTV825
PV5470C104/105 54" Marantz
PV6070C104/105 60" Marantz
Reference Description
00APD020A001 Large Signal Panel
00ASG054A001 Small Signal Panel
00A10688A001 Digital Convergence Panel
00APT191A001 Green CRT Panel
00APT192A001 Red CRT Panel
00APT193A001 Blue CRT Panel
00ATC671A001 Customer Control Assembly
00A10699A001 IR Receiver Panel
00ASW130A001 Switch Panel
00AVJ218A001 Front Jack Panel
00AMP029A001 25W Audio Amp
00A10691A001 Stereo Spread Panel
00A10672C003 Guide Plus Panel
00A10706A001 Remote Locator
00A10696A001 Wallvision Switch Panel
00Z177CEAA01 Remote Transmitter UR617

SMALL SIGNAL PANEL SCHEMATIC & WAVEFORM NOTES:
CAUTION: A SEPARATE ISOLATION TRANSFORMER MUST BE USED WHEN
SERVICING THIS CHASSIS.
SMALL SIGNAL PANEL WAVEFORM NOTES:
UNLESS OTHERWISE SPECIFIED
1. ALL VOLTAGES AND WAVEFORMS WERE TAKEN WITH AN NTSC COLOR BAR
PATTERN SIGNAL APPLIED.
2. SWEEP TIME/DIV SETTINGS ARE SHOWN JUST BELOW THE PHOTOS IN THE
CALIBRATED POSITION. HORIZONTAL POSITIONING OF THE WAVEFORMS WAS
ADJUSTED FOR MAXIMUM CLARITY.
SMALL SIGNAL PANEL SCHEMATIC NOTES:
UNLESS OTHERWISE SPECIFIED:
1. ALL VOLTAGES AND WAVEFORMS WERE TAKEN UNDER THE FOLLOWING
CONDITIONS:
•LINE VOLTAGE MAINTAINED AT 120VAC, 60HZ VIA AN ISOLATION
TRANSFORMER.
•CUSTOMER CONTROLS SET TO FACTORY DEFAULT LEVELS AS FOLLOWS:
COLOR, TINT, AND BRIGHTNESS SET TO MIDRANGE, PICTURE SET TO
APPROXIMATELY 2/3 (BETWEEN MIDRANGE AND FULL ON).
2. WAVEFORMS AND VOLTAGES (WITHOUT BRACKETS) WERE TAKEN WITH AN
NTSC SIGNAL GENERATOR DELIVERING 10mVp-p AT THE ANTENNA
TERMINALS.
3. VOLTAGES SHOWN WITH BRACKETS WERE TAKEN WITH NO SIGNAL APPLIED;
THEY ARE LISTED ONLY WHERE AN APPRECIABLE CHANGE WAS NOTED, OR
AS IN THE SOUND CIRCUITRY WHERE NO VOLTAGES WITH SIGNAL WERE
TAKEN.
4. ALL VOLTAGES ARE POSITIVE DC WITH RESPECT TO THE GROUND LOCATED
IN THAT AREA OF THE CIRCUITRY AND MAY VARY DUE TO NORMAL
PRODUCTION TOLERANCES. VOLTAGE SOURCES ARE ALSO NOMINAL, WITH
THE EXCEPTION OF THE +130Vdc SOURCE (TP4) WHICH IS TIGHTLY
REGULATED TO BE WITHIN +.1Vdc, -2Vdc (MEASURED WITH A .1% DIGITAL
VOLTMETER).
5. SCHEMATIC SYMBOLS:
•INDICATES THESE COMPONENTS ARE SMD "CHIP" TYPE COMPONENTS
AND AS SUCH, WILL BE LOCATED ON THE COPPER SIDE OF THE PRINTED
CIRCUIT BOARD.
-INDICATES THESE COMPONENTS WILL VARY DEPENDING UPON SCREEN
SIZE, PRODUCTION DATES, AND OPTIONAL FEATURES INSTALLED. SEE
THE COMPONENT CHARTS POSTED ON THE SCHEMATIC, OR THE
REPLACEMENT PARTS LIST FOR SPECIFIC PART INFORMATION.
NUMBERS 1 THROUGH 23 CORRESPOND TO WAVEFORM PHOTOS.
6. FOR VOLTAGE, WATTAGE AND TOLERANCE RATINGS OF CAPACITORS OR
RESISTORS, REFER TO THE ELECTRICAL REPLACEMENT PARTS LIST.

LARGE SIGNAL PANEL SCHEMATIC AND WAVEFORM NOTES:
1. ALL VOLTAGES AND WAVEFORMS WERE TAKEN WITH AN NTSC COLOR BAR
PATTERN SIGNAL APPLIED.
2. SWEEP TIME/DIV SETTINGS ARE SHOWN JUST BELOW THE PHOTOS IN THE
CALIBRATED POSITION. HORIZONTAL POSITIONING OF THE WAVEFORMS WAS
ADJUSTED FOR MAXIMUM CLARITY.
LARGE SIGNAL PANEL SCHEMATIC NOTES:
UNLESS OTHERWISE SPECIFIED:
1. ALL VOLTAGES AND WAVEFORMS WERE TAKEN UNDER THE FOLLOWING
CONDITIONS:
•LINE VOLTAGE MAINTAINED AT 120VAC, 60HZ VIA AN ISOLATION TRANSFORMER.
•CUSTOMER CONTROLS SET TO FACTORY DEFAULT LEVELS AS FOLLOWS:
COLOR, TINT, AND BRIGHTNESS SET TO MIDRANGE, PICTURE SET TO
APPROXIMATELY 2/3 (BETWEEN MIDRANGE AND FULL ON).
2. WAVEFORMS AND VOLTAGES (WITHOUT BRACKETS) WERE TAKEN WITH AN
NTSC SIGNAL GENERATOR DELIVERING 10mVp-p AT THE ANTENNA TERMINALS.
3. VOLTAGES SHOWN WITH BRACKETS WERE TAKEN WITH NO SIGNAL APPLIED;
THEY ARE LISTED ONLY WHERE AN APPRECIABLE CHANGE WAS NOTED, OR AS
IN THE SOUND CIRCUITRY WHERE NO VOLTAGES WITH SIGNAL WERE TAKEN.
4. ALL VOLTAGES ARE POSITIVE DC WITH RESPECT TO THE GROUND LOCATED IN
THAT AREA OF THE CIRCUITRY AND MAY VARY DUE TO NORMAL PRODUCTION
TOLERANCES. VOLTAGE SOURCES ARE ALSO NOMINAL, WITH THE EXCEPTION
OF THE +130Vdc SOURCE (TP4) WHICH IS TIGHTLY REGULATED TO BE WITHIN
+.1Vdc, -2Vdc (MEASURED WITH A .1% DIGITAL VOLTMETER).
5. SCHEMATIC SYMBOLS:
•INDICATES THESE COMPONENTS ARE SMD "CHIP" TYPE COMPONENTS
AND AS SUCH, WILL BE LOCATED ON THE COPPER SIDE OF THE PRINTED
CIRCUIT BOARD.
-INDICATES THESE COMPONENTS WILL VARY DEPENDING UPON SCREEN
SIZE, PRODUCTION DATES, AND OPTIONAL FEATURES INSTALLED. SEE
THE COMPONENT CHARTS POSTED ON THE SCHEMATIC, OR THE
REPLACEMENT PARTS LIST FOR SPECIFIC PART INFORMATION.
NUMBERS 1 THROUGH 23 CORRESPOND TO WAVEFORM PHOTOS.
6. FOR VOLTAGE, WATTAGE AND TOLERANCE RATINGS OF CAPACITORS OR
RESISTORS, REFER TO THE ELECTRICAL REPLACEMENT PARTS LIST.

DIGITAL CONVERGENCE PANEL SCHEMATIC AND
WAVEFORM NOTES:
UNLESS OTHERWISE SPECIFIED:
1. ALL VOLTAGES AND WAVEFORMS WERE TAKEN WITH AN NTSC COLOR BAR
PATTERN SIGNAL APPLIED.
2. SWEEP TIME/DIV SETTINGS ARE SHOWN JUST BELOW THE PHOTOS IN THE
CALIBRATED POSITION. HORIZONTAL POSITIONING OF THE WAVEFORMS WAS
ADJUSTED FOR MAXIMUM CLARITY.
DIGITAL CONVERGENCE PANEL SCHEMATIC NOTES:
UNLESS OTHERWISE SPECIFIED:
1. ALL VOLTAGES AND WAVEFORMS WERE TAKEN UNDER THE FOLLOWING
CONDITIONS:
•LINE VOLTAGE MAINTAINED AT 120VAC, 60HZ VIA AN ISOLATION
TRANSFORMER.
•CUSTOMER CONTROLS SET TO FACTORY DEFAULT LEVELS AS FOLLOWS:
COLOR, TINT AND BRIGHTNESS SET TO MIDRANGE, PICTURE SET TO
APPROXIMATELY 2/3 (BETWEEN MIDRANGE AND FULL ON).
2. WAVEFORMS AND VOLTAGES (WITHOUT BRACKETS) WERE TAKEN WITH AN
NTSC SIGNAL GENERATOR DELIVERING 10mVp-p AT THE ANTENNA
TERMINALS.
3. VOLTAGES WITHIN PARENTHESES WERE TAKEN UNDER THE SAME
CONDITIONS AS ABOVE, ONLY WITH NO SIGNAL APPLIED. THEY ARE LISTED
ONLY WHERE AN APPRECIABLE CHANGE WAS NOTED.
4. FOR VOLTAGE, WATTAGE OR TOLERANCE RATINGS OF CAPACITORS OR
RESISTORS, REFER TO THE ELECTRICAL REPLACEMENT PARTS LIST.
5. SCHEMATIC SYMBOLS:
•INDICATES THESE COMPONENTS ARE SMD "CHIP" TYPE COMPONENTS
AND AS SUCH, WILL BE LOCATED ON THE COPPER SIDE OF THE PRINTED
CIRCUIT BOARD.

Cabinet Replacement Parts Lists
Cabinet Exploded View

001152980001
"s" in the "s" column indicates a safety part.
Ref. Ref
No sPart Number Description
AC/CORD 20 s4835 321 17128 AC Cord, Filtered
BACK/BAR 3135 013 01850 Back Barrier
BK/CV/LW 27 3135 013 01440 Back Cover (Lower)
BK/CV/UP 26 3135 013 01010 Back Cover (Upper)
RECEPT 4835 265 97154 Baffle Mount Receptacle (x6)
BATTERY 4835 138 17001 Battery AAA 2Pk
CASTER 4835 528 77071 Caster (x4)
CHAS/FRM 17 4835 432 17943 Chassis Frame
SCRN/BOT 33135 014 02930 Extr., Screen Bottom
SCRN/TOP 14 3135 014 03020 Extr., Screen Edge Top
SCRN/EDG 23135 014 03030 Extr., Screen Edge, Side (x2)
BS/RL/FO 43135 014 03131 Foot Base Rail (x2)
FRM/CONV 16 4835 432 17846 Frame f/Digital Convergence
BS/RL/FRT 63135 013 02381 Front Base Rail
INSERT/H 93135 014 02741 Hole Insert (x12)
INST/BK 3135 015 07350 Instruction Book
JP/FRM 18 3135 014 06650 Jack Panel Frame
JP/OVLAY 19 3135 015 04420 Jack Panel Overlay
LENSF 13 3135 013 01110 Lens, Fresnel
LENSL 10 3135 013 01100 Lens, Lenticular
LIGHT/BAR 22 4835 432 17847 Light Barrier
MIR/BRKT 15 3135 011 02401 Mirror Board Mtng Brkt. (x2)
MIR/MTNG 25 3135 013 00780 Mirror Mounting
MIR/TRAP 24 3135 013 01200 Mirror Trapezoid, 2nd
QUICK/GD 3135 015 07340 Quick Use Guide
REM/TRAN 4835 219 17716 Remote Transmitter UR614
RETAINER 13135 014 02620 Retainer Treelock (x12)
SCRN/FRM 11 3135 014 06550 Screen Frame 52" (x2)
SPEAKER 84835 240 47011 Speaker Full 4x6" 8 Ohm (x2)
SPK/GRL 73135 014 06410 Speaker Grille Cover
Optical Assembly Parts List 007061150001