Phistek ZE5000 User manual

20141229 v2 1
U
Us se er r M Ma an nu ua al l / / I In ns st ta al ll la at ti io on n G Gu ui id de e
A
AV V O Ov ve er r E Et th he er rn ne et t G Gi ig ga ab bi it t A Ad da ap pt to or r
Model No. ZE5000
Warning! It will cause malfunction if the AV Adaptor is operating with unspecified power supply
adaptor or incorrect power voltage. Do not expose this unit in the rain or moisture environment to
reduce the risk of fire or electric shock.
PRECAUTIONS
Do not use the “AV adaptor” and “Power supply Adaptor” near water.
The “AV adaptor” is featured with 75mm x 75mm and 100mm x 100mm VESA mount.
For easy and safe use, it is recommended to mount ”AV adaptor” on the rear cover of monitor with
VESA mount.
The “AV Adaptor” should be operated by an Ethernet cable with standard RJ-45 connector on both
ends. One end to the “AV adaptor”, the other end to host PC or server.
Never spill liquids on the “AV Adaptor”.
Do not attempts to service ”AV adaptor” yourself; opening or removing covers can degrade product
EMC and performance. Please refer all servicing to qualified service personnel.
For Wall mount “Power supply adaptor”, wall socket shall be installed near the equipment and shall
be easily accessible.


20141229 v2 2
Index:
I. Introduction --------------------------------------------------------------------------------------------------- 3~4
Features--------------------------------------------------------------------------------------------------------- 3
Unpack the Adaptor------------------------------------------------------------------------------------------- 3
Check Accessories--------------------------------------------------------------------------------------------- 4
II. Reco ended network application and setting ---------------------------------------------------- 5~11
Basic Extended mode - LAN cable connection block diagram-------------------------------------- 5
Basic Extended mode - USB cable connection block diagram -------------------------------------- 5
Zero Client with with WMS2012 Multipoint
Ethernet( LAN) network connection example --------------------------------------------------- 6
Basic Extended Mode(or Mirror Mode) -----------------------------------------------------------------7~10
Zero Client with Windows MultiPoint Server 2012---------------------------------------------------- 11
III. Driver Installation : Install drivers for extended ode ----------------------------------------------11~19
Install Elite USB Server--------------------------------------------------------------------------------------- 11~13
Install SMSC Driver-------------------------------------------------------------------------------------------- 14~15
Install EETI Touch Driver ------------------------------------------------------------------------------------- 17~19
IV. Mechanical Di ension and Input/ Output ports description ----------------------------------- 20
V. Output signals installation --------------------------------------------------------------------------------- 20
VI. Adaptor installation -----------------------------------------------------------------------------------------21
VII. FCC Warning State ent ------------------------------------------------------------------------------------ 22
VIII. Product General Specification ---------------------------------------------------------------------------- 23
Appendix: Network IP address setting ----------------------------------------------------------------------------- 24~27

20141229 v2 3
I. Introduction
ZE5000 is a Zero Client Audio/Video over Ethernet Adaptor, designed as an endpoint of a PC
sharing solution such as Windows MultiPoint Server 2012
With Windows MultiPoint Server 2012, it can work as a standalone workstation.
The solution enables a host PC(Server) to communicate with multiple and independent stations.
Each station is consisted of one Adaptor (zero client) with a keyboard, mouse, and monitor
connected, allowing multiple users to share the resources/computing of one single server.
By simple Ethernet connection, the server provides each station user with a familiar and
independent Windows® experience.
Features
-Si ple Ethernet connection
ZE5000 connect to Host server through Ethernet cable connection, this type of connection
can exceed the length limit of other signal connection such as VGA, USB. This also gives the
flexibility of system layout.
-Si ple plug and play
Just attach a keyboard, mouse, and monitor to your ZE5000, and connect it to the host server.
A station is set up easily and ready for use right away
-Video output: VGA
-Reset: To reset IP address
-USB upstrea port: option for USB connect application
-Headphone out
-Microphone in/out
Unpack the Adaptor
-Put the AV Adaptor on a clean surface; make sure the box in upright position.
-Remove packing materials from inside of box.

20141229 v2 4
Check accessory
Please make sure the entire accessory is included:
DC 5V Power Adaptor
ZE5000 User Guide &
Driver CD

20141229 v2 5
II. Reco ended network application and setting:
The Phistek Zero Client ZE5000 can be configured to the following modes: -
Basic Extended mode - LAN cable connection block diagram:
-Basic Extended mode - USB cable connection block diagram:
Audio
Audio
USB cable
USB cable
USB cable
LAN cable
VGA
Host PC
Zero Client
#1
Zero Client
#2
Zero Client
#3
Zero Client
#4
Monitor
Display 1
Monitor
Display 2
Monitor
Display 3
Monitor
Display 4
Audio
Audio
VGA
VGA
VGA
Audio
Audio
LAN cable
LAN cable
LAN cable
LAN cable
LAN cable
VGA
Host PC
Gigabit LAN switch
Zero Client
#1
Zero Client
#2
Zero Client
#3
Zero Client
#4
Monitor
Display 1
Monitor
Display 2
Monitor
Display 3
Monitor
Display 4
Audio
Audio
VGA
VGA
VGA

20141229 v2 6
-Zero Client with with WMS2012 Multipoint Ethernet( LAN network connection example
Ethernet( LAN) network connection exa ple

20141229 v2 7
1. Basic Extended Mode (or Mirror Mode):
Please note that Extended ode only provide extended function of video display, audio,
USB ports.
1.1 Set Up Procedures:
1.1.1 Required Hardware Ingredients
The ZE5000 Zero-Client: typically available directly from PHISTEK. The host
co puter: should be scaled according to the usage scenarios
CPU Intel i7 Intel i5 Intel i3 Inel Atom D525
DRAM 8G 8G 4G 2G
OS Win7 64bit Win7 64bit POS Ready7 POS Ready2009
Video 1080p 8 sets(max) 6 sets(max) 0 set 0 sets
Video 720p 8 sets(max) 8 sets(max) 1 sets(max) 0 sets
Photo 1920x1080 8 sets(max) 8 sets(max) 4 sets(max) 4 sets(max)
1.1.2 The LAN network: 10/100M or 1000M Ethernet, recommend Gigabit-Switched,
and ideally having a dedicated switch per each cluster.
1.2 Installation:
Part 1: Host PC Windows OS Preparations
1) Host PC to run Windows-Update and install all available updates.
2) Make sure to install the latest driver for the graphic card (applies to on-board as well).
3) Turn off Windows-Update device driver searching
http://technet.microsoft.com/en-us/library/cc753091.aspx
4) Set Host PC TCP/IPV4 to DHCP
Part 2: Elite Driver installation:
1) Install Elite Driver: (See Page 13, Section III, 2.0)
2) Reboot your computer
Part 3: SMSC Driver Installation & prepare Zero-Client
1) Install SMSC display driver: (See Page 15 Section III, 3.0)
2) Connect all Zero-Clients to Ethernet Switch.
Connect monitors, and sound devices to each client.
3) Launch the Network USB Setting Utility from its desktop shortcut.
Network USB Setting Utility shortcut

20141229 v2 8
4) This program will search for ZE5000 Zero-Clients:
5) Click “Configuration”, tick “DHCP”
6) Per each cluster, per each client terminal:
Click “Assign to this PC”:
7) Windows will identify and install USB sound driver.
8) A dialog may pop up – search for Zero Client software – click cancel.

20141229 v2 9
9) Each client connection will be completed as below:
10) At this stage, you should be able to see all the assigned monitors in active Windows
Desktop mode.
11) Start “ViewSpan Configuration” in the Task-Bar.
Make sure to set all zero client monitors as “Extended”

20141229 v2 10
12). Set up maximum no. zero clients in application
After SMSC driver installation, the system will set number of zero clients in application at”4”
If user wants to connect for more clients, user need to execute “regedit.exe”
Simply input “regedit “to search this application.
Then follow the route:
HKEY_LOCAL_MACHINE/SYSTEM/CurrentControlSet/services/sgfxk :
MAxNumberOfUsbAdapters REG_DWORD 0x00000004 (4)
The default number is 4, click MAxNumberOfUsbAdapters to change number
The numbers of clients to use depend on the Host PC resources,
Recommend maximum number set <10
2. Zero Client with Windows MultiPoint Server 2012
2.1 With Windows MultiPoint Server 2012, zero clients can work independently as
standalone PC
2.2 Pls visit Microsoft Website for Windows MultiPoint Server 2012Evaluation.
to get image and installation guide.
http://www.microsoft.com/en-us/download/details.aspx?id=35821
2.3 In addition to the image, pls visit Phistek website to download following drivers
Elite Driver for wms2012:
GenericWMSZeroClientService_Setup_13_1217_S0122_G1042_Cert
SMSC driver for wms2012:
SetupSgfxWmsFbr-5_3_60_8411
Patch file:
WMS-KB2791647-ENU-x64
Please mail to: [e-mail] or phist[email protected] to get download access
code.