Phistek ZE7000 Installation and operating instructions

20141229 v1.0 1
U
Us se er r M Ma an nu ua al l / / I In ns st ta al ll la at ti io on n G Gu ui id de e
A
AV V O Ov ve er r E Et th he er rn ne et t G Gi ig ga ab bi it t A Ad da ap pt to or r
M
Mo od de el l N No o. . Z ZE E7 70 00 00 0/ / Z ZE E7 70 00 00 0
Warning! It will cause malfunction if the AV Adaptor is operating with unspecified power supply adaptor or
incorrect power voltage. Do not expose this unit in the rain or moisture environment to reduce the risk of fire or
electric shock.
PRECAUTIONS
Do not use the “AV adaptor” and “Power supply Adaptor” near water.
The “AV adaptor” is featured with 75mm x 75mm and 100mm x 100mm VESA mount.
For easy and safe use, it is recommended to mount ”AV adaptor” on the rear cover of monitor with VESA
mount.
The “AV Adaptor” should be operated by an Ethernet cable with standard RJ-45 connector on both ends.
One end to the “AV adaptor”, the other end to host PC or server.
Never spill liquids on the “AV Adaptor”.
Do not attempts to service ”AV adaptor” yourself; opening or removing covers can degrade product EMC
and performance. Please refer all servicing to qualified service personnel.
For Wall mount “Power supply adaptor”, wall socket shall be installed near the equipment and shall be
easily accessible.


20141229 v1.0 2
Content Index:
I. Introduction --------------------------------------------------------------------------------------------------------------------- 3
II. Features --------------------------------------------------------------------------------------------------------------------------- 3
III. Un ack the Ada tor------------------------------------------------------------------------------------------------------------ 3
IV. Check Accessories--------------------------------------------------------------------------------------------------------------- 4
V. Recommended network a lication and setting ---------------------------------------------------------------------- 5
1. Set u Procedures -------------------------------------------------------------------------------------------------------- 6
2. Installation Procedure --------------------------------------------------------------------------------------------------- 6
(1) Windows OS Preparation ---------------------------------------------------------------------------------------- 6
(2) Turn on Microsoft NET. Framework --------------------------------------------------------------------------- 6
(3) Drivers Installation ------------------------------------------------------------------------------------------------ 7
3.1 Install Network USB Driver ---------------------------------------------------------------------------- 7
3.2 Install DisplayLink USB Graphics Software for Windows* V7.6 M1 ------------------------- 11
(4) Network IP address ----------------------------------------------------------------------------------------------- 12
VI. Product Outline and I/O Descri tion-------------------------------------------------------------------------------------- 16
VII. Product In ut / Out ut Installation --------------------------------------------------------------------------------------- 17
VIII. Zero Client Ada tor mounting method----------------------------------------------------------------------------------- 18
IX. EMC Warning Statement------------------------------------------------------------------------------------------------------ 20
X. Product General S ecification ---------------------------------------------------------------------------------------------- 21

20141229 v1.0 3
I. Introduction
ZE7000/ ZE7000 Zero Client operates as a stand-alone computing model without local CPU, memory, :
-Connected to Host PC only with a Ethernet cable,
-Video, audio and USB functions are all communicated through this cable.
ZE7000/ ZE7000 Zero Client decode Video, Audio from Ethernet to USB, then with video, audio
decoders to translate USB to video (for monitor), audio amplifier and microphone.
It also includes a USB Hub, with 4 downstream ports, upstream is internally communicated to Ethernet
and connected to Host PC.
ZE7000 is a ZE7000 Zero Client with embedded security code to apply for Phistek eSignage application
software.
II. Features
-Sim le Ethernet connection for multi le extended dis lays
ZE7000/ ZE7000 connect to Host server through Ethernet cable connection, this type of connection can
exceed the length limit of other signal connection such as VGA, USB. This also gives the flexibility of
system layout.
-Easy and convenient installation
Designed with VESA standard mounting on the adaptor box;
75mm x 75mm and 100mm x 100mm
-Provides three ty es of video signals for end user to select
VGA (by an attached DVI to VGA dongle)
DVI-D (through a DVI-D to DVI-D cable)
Reset: To reset IP address
-Audio Line out
-Head hone out
-Micro hone in/out
III. Un ack the Ada tor
-Put the AV Adaptor on a clean surface; make sure the box in upright position.
-Remove packing materials from inside of box.

20141229 v1.0 4
IV. Check accessory
Please make sure the entire accessory is included:
oR
DVI to VGA Dongle DC 12V Power Adaptor
ZE7000 User Guide &
Driver CD
ZE7000+User Guide &
Driver CD

20141229 v1.0 5
V. Recommended network a lication and setting:
The Phistek ZE7000/ ZE7000 can be configured as below:
-ZE7000: with Microsoft Basic Extended Mode(or Mirror Mode) for multi le extended dis lays
Multiple extended displays block diagram : simple extended displays, no control center at Host PC
ZE7000+: Add Phistek eSignage+ a with Microsoft basic extended mode for multi le extended
dis lays
ZE7000+, with eSignage+ a lication exam le:
eSignage+ create a control center at Host PC to broadcast and monitor each zero client
Audio
Audio
LAN cable
LAN cable
LAN cable
LAN cable
LAN cable
VGA/ DVI-D
VGA/ DVI-D
VGA/ DVI-D
Host PC
Gigabit LAN switch
ZE7000
#1
ZE7000
#2
ZE7000
#3
ZE7000
#4
Monitor
Display 1
Monitor
Display 2
Monitor
Display 3
Monitor
Display 4
VGA/ DVI-D
Audio
Audio
Phistek eSigange SW
create a control center
/panel in Host PC to
broadcast and monitor
each zero client

20141229 v1.0 6
1. Set U Procedures:
The ZE7000/ ZE7000+ Zero-Client: typically available directly from PHISTEK.
The host com uter: should be scaled according to the usage scenarios
The
LAN network switch: 10/100M or 1000M Ethernet, recommend Gigabit-Switched, and ideally
having a dedicated switch per each cluster.
2. Installation rocedure:
(1). Windows OS Preparations
(2). Turn on Microsoft NET. Framework:
(3). Drivers Installation: Network USB Driver:
Network USB Driver for ZE7000 e_Signage _Setup_1014
Network USB Driver for ZE7000 Network_USB_Service_Setup_13_0731_1084
DisplayLink Driver for ZE7000 & ZE7000 DisplayLink USB Graphics Software for Windows* V
7.6.M1
(4). Network IP address setting
(1). Windows OS Pre arations
Run Windows-Update and install all available updates.
Make sure to install the latest driver for the graphic card (applies to on-board as well)
Turn off Windows-Update device driver searching
http://technet.microsoft.com/en-us/library/cc753091.aspx
(2). Turn on Microsoft NET. Framework:
Click Control Panel to enter Programs.
In Programs, Please check “ Turn Windows Features on or off”
CPU Intel i7 Intel i5 Intel i3 Inel Atom D525
DRAM 8G 8G 4G 2G
OS Win 8.1, Win7
Win 8.1, Win7 POS Ready7 POS Ready2009
Video 1080p 8 sets(max) 6 sets(max) 0 set 0 sets
Video 720p 8 sets(max) 8 sets(max) 1 sets(max) 0 sets
Photo 1920x1080 8 sets(max) 8 sets(max) 4 sets(max) 4 sets(max)

20141229 v1.0 7
Find and turn on Microsoft. NET Framework (it shall be later than 3.5.1 version)
Please see the Fig. below.
(3). Drivers Installation:
3.1 Install Network USB Driver:
Click “e_Signage _Setup_1014” (ZE7000 )
Click “Network_USB_Service_Setup_13_0731_1084”(ZE7000)
Installation is automatically run as below:
ZE7000 : e_Signage _Setup_1014 ZE7000: Network_USB_Service_Setup_13_0731_1084

20141229 v1.0 8
Software configuration proceeding……
ZE7000 : e_Signage _Setup_1014 ZE7000: Network_USB_Service_Setup_13_0731_1084
After installation, screen will display as below, please press “Finish”
ZE7000 : e_Signage _Setup_1014 ZE7000: Network_USB_Service_Setup_13_0731_1084

20141229 v1.0 9
Screen will then display as below, please choose to restart your computer.
After Host PC restart, there will be a shortcut Icon on the screen desktop.
ZE7000 : e_Signage _Setup_1014 ZE7000: Network_USB_Service_Setup_13_0731_1084
For ZE7000 , click eSignage short cut will reveal “eSignage control center” as below:

20141229 v1.0 10
Click the red circle icon, will reveal Network USB Setting utility as below:
(For ZE7000, click “Launch Network USB Setting Utility” shortcut will reveal same utility)
User can use this utility to assign/ clear connection, and configure IP address.
For eSignage , pls refer to eSignage user guide for detail application.

20141229 v1.0 11
3.2 Install Dis layLink USB Gra hics Software for Windows* V7.6 M1
Click Installation The Displaylink software end user Licence agreement shown as below:
Click I Accept, the DisplayLink Core Software installs
Displaylink USB Graphic software installation will complete without notification.
Note: On some computers you may need to reboot before you can use your Displaylink enabled
device

20141229 v1.0 12
(4). Network IP address setting:


Note: All zero clients’ IP address shall be in the same segment
For example:
Host PC: IP address=192.168.1.10, Subnet mask=255:255:255:0
Zero clients shall be
IP=192.168.1.xxx, Subnet mask=255:255:255:0


There are two ways to set u IP address:
DHCP:
See a general home network diagram below as an example:
Connect Host PC and zero clients to a network switch(better to use Gigabit switch). The Router
will automatically assign IP via switch to devices connect to this switch
Host PC
Zero Client A
Zero Client B
ADSL Modem
Router
Gigabit
LAN switch

20141229 v1.0 13
Check if zero clients are at DHCP status:
Click configuration, a set up table will appear, DHCP shall be ticked.
Set Host PC to DHCP: see below properties of IPV4
: tick “Obtain an IP address automatically

20141229 v1.0 14
After all devices’ IP address has been set up to DHCP, the router will assign IP automatically,
the USB server utility will look like as below:
Click Assignment to this PC for each client, connection will be made:

20141229 v1.0 15
If the client IP is not in the same segment, the IP address shown is RED, see example below:
Please tick “DHCP” to get DHCP IP.
Manual assign IP:
If the system is for local use( not connect to router to website),
you may also assign IP manually,
The IP address shall be in the same segment, and Subnet mask shall be the same.
For example:
Host PC: IP=192.168.1.1, subnet: 255:255:255:0
Zero Client A IP=192.168.1.11, subnet: 255:255:255:0
Zero Client B IP=192.168.1.12, subnet: 255:255:255:0.

20141229 v1.0 16
VI. Product Outline and I/O Descri tion: dimension(mm)

20141229 v1.0 17
VII. Product In ut / Out ut Installation:

20141229 v1.0 18
VIII. Zero Client Ada tor mounting method:
ty e 1
ty e 2

20141229 v1.0 19
ty e 3
ty e 4

20141229 v1.0 20
IX. EMC Warning Statement:
FCC Class A Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.