Phoenix MRS 64/1000 Series Use and care manual

MRS 64/1000 & 64/1000S Series
Installation Instructions & Repair Parts List
Phoenix Products Company Inc. 8711 West Port Avenue Milwaukee, WI 53224 USA
Phone: [phone] Toll Free: 800.438.1214 Fax: [phone] www.phoenixlighting.com
!CAUTION
• All wiring should be done by a licensed electrician in accordance with state codes, local codes and National Electric Code (NEC) standards.
• Improper installation may result in serious injury and void warranty.
• When fixture is installed in a Class I, Division 2 Hazardous Location, strict compliance to the fixture warning label instructions must be met.
• Wiring connections must be made with metal conduit or flexible cord in compliance with Class I, Division 2 wiring methods defined in the National Electric
Code.
• Use protective gloves and eye equipment when replacing lamps.
Mounting
Fasten fixture with four (4) ⅜ inch bolts through holes provided in mounting base. Do not mount on unsupported cab or house roof. Attach near corner supports
or use adequate sub-base. Avoid mounting on light-weight cross members of booms or derricks which will vibrate or flex excessively. In addition to normal (base
down) mounting fixture may be attached in a pendant or cantilever manner.
Lamping
The MRS 64/1000 Series fixtures are designed to use incandescent and quartz tube halogen cycle par 64 lamps. Lamping is accomplished through the hinged
cover glass assembly. Loosen three (3) wing nuts on lamp support ring and rotate lamp retaining ring free from wing nuts to release lamp from supporting ring. To
replace a lamp the procedure must be reversed and the three (3) wing nuts snugly finger tightened.
When relamping, it is recommended that the cover glass be cleaned to maintain fixture efficiency (see cleaning).
Aiming
Aiming adjustments are made by loosening the single bolt (or handle on “S” model) that attaches the harp to the mounting base and the two (2) bolts (or handle
on the “S” model) holding the fixture to the harp. The fixture can then be positioned to the desired aiming point. The fixture may be rotated 180 degrees about
each of the two adjustable axes for proper aiming. It may be necessary, in some installations, to rotate the fixture for easier access for relamping. The same
procedure as for aiming should be employed.
Quartz Tube Halogen Cycle Lamp or ANSI Number Incandescent Lamp or ANSI Number
Q1000 Par 64/MFL 500 Par 64/MFL
Q1000 Par 64/WFL 500 Par 64/WFL
Q1000 Par 64/NSP 500 Par 64/NSP
Q1000 Par 64/VNSP
Wiring
The fixtures are pre-wired with a five (5) foot three (3) conductor electrical cord “pigtail” for wiring to suitable power source. The green conductor is grounded to
the fixture and must be connected to a positive ground. Do not connect green wire to power source.
Lamp Type Designations

Installation Instructions & Repair Parts List
MRS 64/1000 & 64/1000S Series
Phoenix Products Company Inc. 8711 West Port Avenue Milwaukee, WI 53224 USA
Phone: [phone] Toll Free: 800.438.1214 Fax: [phone] www.phoenixlighting.com
Repair Parts List
Item Qty Description MRS 64/1000 (Part No.) MRS 64/1000S (Part No.)
floodlight assembly complete 1010400 1010700
1 1 lamp/socket support assembly 1621900 1621900
2 1 base assembly 1817100 1821300
3 4 bolt-nut assembly, ¼ - 20 1817400 1817400
4 1 handle assembly -1821100
5 1 handle assembly -1821200
6 1 diaphragm ring, 9 -⅓ O.D. contact factory contact factory
7 1 harp 2400900 contact factory
8 1 door frame 2634600 2634600
9 1 heat sheild 2634710 2634710
10 4cover glass retaining clip 2751750 2751750
11 1s.s. bushing, ¾ O.D. -2649400
12 1s.s. bushing, ½ O.D. -2649600
13 1handle bracket -2649700
14 1snap bushing 4024200 4024200
15 1cord grip, ½ inch 4032000 4032000
17 1cord assembly, 5 foot 4116800 4116800
18 1mogul-end-prong lamp socket 4502200 4502200
19 1flat cover glass (lens)
rounded cover glass (lens)
4610009
contact factory 4610009 contact factory
20 1cover glass gasket 5002202 5002202
21 4s.s. round head machine screw, 10-24 x ⅜ 6009500 6009500
22 12 Phillips pan head type F machine screw, 6-32 x ½ 6001600 6001600
23 2s.s. Phillips flat head machine screw, 10-24 x ⅝ -6001800
24 1Phillips pan type F machine screw, 6-32 x ⅜ 6002900 6002900
25 1s.s. hex head cap screw, ⅝-11 x 1-¼ 6032300 -
26 2s.s. hex head cap screw, ⅜ x 1-¼ 6032800 6032800
27 1s.s. hex head cap screw, ½-13 x ¾ -6033600
28 1s.s. hex jam nut, ⅝-11 -6201400
29 2s.s. flat washer, ⅜ -6300500
30 1s.s. flat washer, ⅝ -6300700
31 4s.s. split lock washer, No. 8 6311000 6311000
32 1s.s. split lock washer, ⅝ 6311700 -
33 2s.s. split lock washer, ⅜ 6311800 6311800
34 1s.s. split lock washer, ½ -6311900
35 4s.s. spring pin, ⁄ D. x ⅞ 6510300 6510300
36 2s.s. spring pin, ¼ D. x 1 inch 6510400 6510400
37 1plastic handle, 1-¼ D. x 4-½ (½ - 13 insert) -7300200

Phoenix Products Company Inc. 8711 West Port Avenue Milwaukee, WI 53224 USA
Phone: [phone] Toll Free: 800.438.1214 Fax: [phone] www.phoenixlighting.com
MRS 64/1000 & 64/1000S Series
Installation Instructions & Repair Parts List
Phoenix Products Company Inc. 8711 West Port Avenue Milwaukee, WI 53224 USA
Phone: [phone] Toll Free: 800.438.1214 Fax: [phone] www.phoenixlighting.com
Cleaning
If the interior surface of the cover glass or reflector surface becomes dirty, it is recommended that they be cleaned to maintain maximum output. Remove the
socket housing to gain access into the fixture. The glass may be cleaned with any non-abrasive conventional glass cleaner. The reflector should be cleaned with
a soft cloth using soapy water or special reflector cleaners.
To prevent gaskets from sticking at sealing surfaces, lightly apply a liquid silicone release agent to gaskets when replacing any of the access covers. For best
results, wipe first application until dry (to clean the gasket surface) and then apply a second application and allow to remain wet.
5
8
21
29
19
Repair Parts
Product design and specifications are subject to change without notice.
N5459700K
03.19.18
20
22
10
31
6
18
27
34
13
37
23
36
35
3
24
9
17
15
14
1
7
4
30
11
2
28
29
12
26
33
25
32