PhotoHigher AV130 360 PAN KIT MR User manual

AV130 360°PAN KIT MR
360 Pan kit assembly instructions for the
Mini AV130 Camera Gimbal for Multirotors

COMPONENT CHECKLIST 1.
Page 1
100-1165 AV1-AV130 PAN SERVO BRACKET
100-1157 AV1-AV130 PAN SHAFT
100-1163 AV1-AV130 PAN SKIDS
100-1162 AV2-AV200 SKID BASE COMMON
HH-DS16 FCD HH-HYPERION DS16FCD SERVO
SC-44T 48P SERVO GE SC-44T SERVO GEAR (Futuba)
CS- 10-1.OMG 304N CR3 FS- M10 LOCK NUT
HH-TREX 450 MAINGEAR HH-T-Rex 450 MAIN GEAR
100-1164 AV1-AV130 PAN SPACER
F6701 ZZ ABS- 12x18x4mm BEARING + FLANGE
100-1128 AV2-AV200 BOTTOM BEARING BRACKET
100-1021 OR- ROLL BEARING SPACER - 50.8mm
100-1020 OR- STANDARD SPACER - 60mm
CSB-BH M3X6 CS ZINC FS- M3x6 BUTTON HEAD CS ZINC
LN-M3 FS- M3 LOCK NUT
QTY 1
QTY 1
QTY 4
QTY 2
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 2
QTY 1
QTY 6
QTY 4
QTY 48
QTY 32

ASSEMBLY INSTRUCTIONS 2.
QTY 4
QTY 2
QTY 1
QTY 1
QTY 2
QTY 4
QTY 1
QTY 1
Affix the servo bracket to the servo
using countersink screws.
Page 3Page 2
STEP 1 : PAN SERVO
NOTE: Potentiometer is not connected to anything - this is how the 360 servo
works. Turn the servo on and adjust the pot shaft if neccessary to get it to
the neutral position.
Once you have it set to neutral you can fix it in place using heatshrink
to cover the pot shaft and prevent it from being bumped and moved.
CS-M3X6 COUNTRSINK FS- CSK M3x6 ZINC
100-1178 AV1-AV130 BATTERY TRAY
100-1192 AV2- PAN AXES BEARING SPACER
100-1131 DROIDWORX ADAPTOR PLATE
LG360GRE DW-GEAR RAIL PLATES
200-1219 AV2- GROMET 3.2mm / 10.3mm hole
200-1180 AV2-12X3.2mm NYLON WASHER
100-1231 WAVY WASHER

Assemble skids using 50.8mm roll bearing spacers
and M3x6 buttonhead screws.
Insert the bearing into the bearing bracket,
with the flange on the under side.
Assemble battery tray with 60mm spacers, M3x6 buttonheads
rubber grommets, and the Droidworx adaptor plate.
Page 5Page 4
STEP 2 : LANDING SKIDS STEP 3 : LOWER BEARING BRACKET
STEP 4 : BATTERY TRAY

Slide the bracket into place and secure with M3x6 buttonhead screws. Insert the pan shaft from inside through
the bearing bracket.
Slide the spacer onto the pan shaft
from the top of the gimbal.
Page 7Page 6
STEP 5 : INSTALLING THE LOWER BRACKET STEP 6 : INSTALLING THE PAN SHAFT
STEP 7 : PAN AXES BEARING SPACER

Place the second bearing with flange over the pan shaft and push it in until it is
flush with the gimbal surface.
Secure the servo in place with M3x10 screws.
Page 9Page 8
STEP 8 : BEARING PLACEMENT
Slide the servo into the gimbal
on an angle as shown.
If this method proves
problematic you can
separate the serve
from its bracket
and slide that in first.
Place the servo gear and fix in place using the servo screw.
STEP 9 : INSTALL THE SERVO STEP 10 : Servo gear

Page 11Page 10
The nylon washer sits on top of the main gear.
STEP 13 : Nylon Washer
Place the main gear (blue) hub side up, and fit the pan spacer into it with the
raised lip facing up.
STEP 11 : MAIN GEAR ASSEMBLY
Fit the main gear, hub side down, onto the pan shaft. Slide the servo gear toward
the main gear so that the teeth of the two gears are interconnected.
STEP 12 : AFFIX THE TWO GEARS
Position the pre-assembled battery tray on the main gear and fix in place tightly
using the wavy washer, then the lock nut.
STEP 14 : ATTACHING THE BATTERY TRAY

Page 13Page 12
Attach the pre-assembled skids to the gimbal
using M3x6 buttonhead screws. The screws
should be positioned on the interior of the
gimbal with the M3 lock nuts on the exterior.
STEP 15 : ATTACHING SKIDS