PhotoHigher AV200 User manual

AV200 360°PAN KIT MR
360 Pan kit assembly instructions for the
Pro AV200 Camera Gimbal for Multirotors

COMPONENT CHECKLIST 1.
100-1129 AV2-AV200 PAN SERVO BRACKET QTY 1
100-1158 AV2-AV200 PAN SHAFT QTY 1
100-1161 AV2-AV200 PAN SKIDS QTY 4
100-1162 AV2-AV200 SKID BASE COMMON QTY 2
ABS-6M16M130SF6008 MXI- TIMING PULLEY 130t ID8mm QTY 1
HOT-SC-0352 HOT-SAVOX PAN SERVO SC-0352 QTY 1
MXLS-02 Futuba MXL- PULLEY MXL 32t Futuba QTY 1
ABS-A 6Z16M153045 MXL- TIMING BELT 153t x 4.5mm QTY 1
F6701 ZZ ABS- 12x18x4mm BEARING + FLANGE QTY 2
CS- 10-1.OMG 304N CR3 FS- M10 LOCK NUT QTY 1
100-1021 OR- ROLL BEARING SPACER - 50.8mm QTY 6
100-1020 OR- STANDARD SPACER - 60mm QTY 4
CSB-BH M3X6 CS ZINC FS- M3x6 BUTTON HEAD CS ZINC QTY 48
LN-M3 FS- M3 LOCK NUT QTY 32
CS-M3X6 COUNTRSINK FS- CSK M3x6 ZINC QTY 4
Page 1

ASSEMBLY INSTRUCTIONS 2.
CSB-M3X10ZP FS- BUTTON HEAD CS M3x10 ZP QTY 4
100-1192 AV2- PAN AXES BEARING SPACER QTY 1
100-1179 AV2-AV200 BATTERY TRAY QTY 2
LG360GRE DW-GEAR RAIL PLATE QTY 2
100-1128 AV2-AV200 BOTTOM BEARING BRACKET QTY 1
200-1219 AV2- GROMET 3.2mm / 10.3mm hole QTY 4
200-1180 AV2-12X3.2mm NYLON WASHER QTY 1
100-1231 WAVY WASHER QTY 1
Affix the servo bracket to the servo
using countersink screws
Page 3Page 2
STEP 1 : PAN SERVO
IMPORTANT: First check that the 360 servo is not creeping before installation.
Plug in the servo to RX and turn it on.
If the servo creeps then try to stop it by using sub trim.
If the sub trim does not stop it you need to remove the top cover
from the servo.
Lift out gear and you will see the top of the potentiometer.
Turn the shaft to find the neutral position.

Assemble skids using 50.8mm roll bearing spacers
and M3x6 buttonhead screws
Insert the bearing into the bearing bracket,
with the flange on the under side
Assemble battery tray with 60mm spacers, M3x6 buttonheads
rubber grommets, and the Droidworx adaptor plate
Page 5Page 4
STEP 2 : LANDING SKIDS STEP 3 : LOWER BEARING BRACKET
STEP 4 : BATTERY TRAY

Slide the bracket into place and secure with M3x6 buttonhead screws Insert the pan shaft from inside through
the bearing bracket
Slide the spacer onto the pan shaft
from the top of the gimbal
Page 7Page 6
STEP 5 : INSTALLING THE LOWER BRACKET STEP 6 : INSTALLING THE PAN SHAFT
STEP 7 : PAN AXES BEARING SPACER

Place the second bearing with flange
over the pan shaft and flush
with the gimbal surface
Secure the servo in place with M3x10 screws
Page 9Page 8
STEP 8 : BEARING PLACEMENT
Slide the servo into the gimbal on an
angle as shown.
If this method proves problematic
you can separate the servo from its
bracket and slide that in first
Attach the pulley, the timing belt and the timing pulley. The timing pulley should
be positioned flange side down with the hub underneath.
STEP 9 : INSTALL THE SERVO STEP 10 : PULLEY ASSEMBLY

Place the assembled battery tray on top. Fix in place
with the following parts in this order:
1. Nylon Washer
2. Wavy Washer
3. M10 Lock Nut
Page 11Page 10
STEP 11 : BATTERY TRAY
Attach the pre-assembled skids to the gimbal using M3x6 buttonhead screws.
The screws should be positioned on the interior of the gimbal with the M3 lock nuts
on the exterior.
STEP 12 : ATTACHING SKIDS