Pickle-ball Kollectaball Max User manual

Kollectaball comes unassembled to
allow for more cost-eective and safer
shipping. Assembly will require roughly
40 minutes for a rst-time assembler.
IF YOU REQUIRE ASSEMBLY ASSISTANCE,
WE ARE HERE TO HELP.
CALL TOLL FREE 1-888-854-0163 OR
EMAIL inf[email protected]
Kollectaball Max Assembly Instructions
Kollectaball Max Assembly Instructions
Thank-you for purchasing a Kollectaball Max. Kollectaball Max
Thank-you for purchasing a Kollectaball Max. Kollectaball Max
is the clever way to collect tennis and pickleballs, allowing
is the clever way to collect tennis and pickleballs, allowing
more time for playing and less time and eort collecting!
more time for playing and less time and eort collecting!
Kollectaball Max can also pick up
Pickleball Balls!

Before assembly, the following
tools are required:
1. Protective Eye wear
2. Flat Head Screwdriver
3. Pliers
1. Cone (R127) x 2
2. Wire Mounting Disk
(R090) x 2
3. Cage Holder (R182)
4. Wire Opener (R195)
5. Stand (R227)
6. Wire (R101) x 62
7. Handle Lower Section
(R211)
8. Handle Upper Section
(R210)
9. Coupler (R219,
Inside Handle)
10. Allen Key
11. Wrench
12. Wire RemovalTool
(R062)
13. Cam (R235)
14. Screw (R050) x 2
15. Hex Screw (R198)
16. Bolt (R197) x 2
17. Washer (R178) x 2
18. Lock Nut (R137) x 7
1 2
3 4
5
6 7 8
9
10
11 12 14 15 16 17 18
13
1
2 3

STEP 1: Assembling the Cage
STEP 2: Assembling the Handle
Remove the R219 Coupler
from inside the R210 Handle
Upper Section and remove both
Allen Key Screws.
Join the two sides of the Coupler and
insert into the R210 Handle Upper Section
so that the hole in the Coupler is aligned with
the hole in the Handle. Insert an Allen Key
Screw in the Handle to secure, but do not
tighten all the way.
Slide the R211 Handle Lower Section over
the exposed coupler so the holes align.
Insert the second Allen Key Screw and
tighten both using Allen Key.
DO NOT OVERTIGHTEN.
The numbered white sticker on the mounting disk helps to indicate
the next available slot. Place one Wire Mounting Disk (R090) on
a at surface and insert Wire (R101) into slot #1 as shown.
You will hear it click into place.
DO NOT INSERT THE WIRE UPSIDE DOWN.
X
Insert the 2 Cones (R127)
on the inside of the cage.
Remove the white
stickers from the
mounting disks.
Secure with an M6 Lock Nut by using the wrench provided.
Do not over tighten as it may damage the cone.
For Tennis Balls Collecting Cage
Being careful not to miss any slots,
continue inserting wires in numeric
order until all 60 slots are full.
Store the 2 extra wires in case
damaged wires need to be
replaced in the future.
For Pickleballs Collecting Cage
Continue inserting wires into
EVERY 2ND SLOT. Store the 32
extra wires in case damaged wires
need to be replaced in the future.
Insert wire #1 from the
complete mounting disk
into slot #1 on the 2nd disk.
Continue in numeric order
until the cage is complete.

STEP 3: Wire-Opener and Stand Assembly
STEP 4: Attaching the Cage to the Cage Holder
Insert the R211 Handle Lower
Section through the R195Wire
Opener.With theWire Opener in
the position shown, twist the handle
90 degrees and slide theWire
Opener up so the holes on the Wire
Opener and Handle are aligned.
Place R178 washer on one side of the
wire-opener with the at side facing
outwards and insert R198 hex screw.
Place the second R178 washer on the
other side and tighten the R198 screw.
Fasten with R137 lock nut.
Insert R182 Cage Holder into
the handle, but DO NOT FASTEN.
Remove the lock nut from R235 Cam
and insert as shown in the above
image. Secure with the lock nut,
but ONLY FINGERTIGHT.
Fasten the Cage Holder to the handle using the
two R197 bolts and the R137 lock nut. Be sure to
insert the bolts from below with the lock
nut on top. Insert BOTH bolts and fasten hand
tight BEFORE tightening with the wrench.
Using a at head screwdriver and pliers, fasten R227 Stand to the wire
opener using the R050 screws and R137 lock nuts. Be sure to insert the
screw from the top with lock nut underneath. Fasten tightly.
Align the holes on the ends of the cage with
the cage holder and squeeze into place.
Note the direction
of the stand
Kollectaball is a trade mark of IntoEuropeSales Ltd. Distributed in North America by RCS Sports
You are
now ready
to enjoy
your
Kollectaball!