Piera Canaree i1 User manual

Canāree i1 Configuration Guide
Real-Time Air Quality Monitoring Industrial IoT Device
Initial Configuration Guide – Version 1.2.2 updated 10/6/21
Piera Systems Inc. reserves the right to make corrections, modifications enhancements, improvements and other changes to its products and
services at any time and to discontinue any product or service without notice. Please contact Piera Systems anytime to obtain the latest relevant
information - We are ready to help you determine which of our solutions will best meet your needs contact [e-mail] for information.
© 2021 Piera Systems Inc. Page | 1

Canāree i1 Deployment Options
Canāree i1 supports a variety of deployment scenarios to IoT-Enable Piera IPS-Series
Intelligent Particle Sensors in most common networking environments including:
Wired Ethernet / PoE Powered
Operating as a Class 0 PoE+ Device consuming < 2W @ 48VDC the device will receive
power and internet access from an Ethernet Switch or “48V PoE Injector” using either
DHCP (Default) or Static IP Addressing.
Canāree I1E Ethernet Port 48V PoE+ Switch or Injector
Wired Ethernet / USB Powered
If your Ethernet Switch does not support PoE+ for power the device can be powered
via a reliable USB 5V source including standard power adapters or battery packs. The
power source used should support up to 1.5Amps such as most Rapid Charger USB
Adapters. Internet access is provided via the Ethernet Connection using DHCP
(default) however Static IPv4 addressing is supported.
Piera Systems Inc. reserves the right to make corrections, modifications enhancements, improvements and other changes to its products and
services at any time and to discontinue any product or service without notice. Please contact Piera Systems anytime to obtain the latest relevant
information - We are ready to help you determine which of our solutions will best meet your needs contact [e-mail] for information.
© 2021 Piera Systems Inc. Page | 2

Wireless / USB Powered -
The device can be programmed for your 802.11n
(2.4ghz only) Wireless network using WPA2 / PSK
and will operate remotely via the included 5V USB
Adapter. SenseiAQ Software is used to initially
provision the Wifi network settings.
Wireless / PoE Powered -
The device can be programmed for Wifi and still
receive power via the PoE Ethernet Port or injector;
however the Ethernet “Link” will remain down while
operating in this mode
Power Failover
The onboard circuitry supports failover between PoE+ power and USB Power
automatically. PoE+ will be used when available during power-on.
Notes on External Antenna for 2.4g Wifi Specifications
Canāree i1 supports external Wifi antennas for the 2.4Ghz Band using a single stream
RP-SMA connector. The factory antenna is unidirectional and operates at +4dbM. and
can operate up to 400’ from a Wireless AP in most circumstances. 3rd party antennas
can extend range and coverage beyond this point and improve connectivity in poor Wifi
coverage areas. For more information on supported antennas contact
PieraSystems.com/support
Piera Systems Inc. reserves the right to make corrections, modifications enhancements, improvements and other changes to its products and
services at any time and to discontinue any product or service without notice. Please contact Piera Systems anytime to obtain the latest relevant
information - We are ready to help you determine which of our solutions will best meet your needs contact [e-mail] for information.
© 2021 Piera Systems Inc. Page | 3

Getting Started Guide
If using either Wired Ethernet deployment option, your device is immediately ready to
install - The factory default settings for the device will attempt to DHCP on the Ethernet
link to obtain an IP Address, DNS and Gateway IP. If successful it will phone home to
the SenseiAQ Cloud Service
If using Wireless deployment mode, the device will need to be configured to your
Wireless Networks settings before bringing online. SenseiAQ Software version
1.2.2 or greater is required to configure Wifi settings and register devices to your
SenseiAQ Cloud Account. The latest version of our software is available on GitHub to
Download: https://github.com/PieraSystems/SenseiAQ
Configuration and Registration using SenseiAQ
When running SenseiAQ will begin searching for your local USB-Connected sensor
until a device is connected. A notice will instruct you to download a driver if required.
Once the Canāree I1E is connected it will appear as a local (USB) device in SenseiAQ.
Here you can monitor sensor information in real-time and use all the features of the
SenseiAQ App locally or configure the device for network operation. The full user
guide for SenseiAQ Software is available at https://pierasystems.com/support/
Piera Systems Inc. reserves the right to make corrections, modifications enhancements, improvements and other changes to its products and
services at any time and to discontinue any product or service without notice. Please contact Piera Systems anytime to obtain the latest relevant
information - We are ready to help you determine which of our solutions will best meet your needs contact [e-mail] for information.
© 2021 Piera Systems Inc. Page | 4

Once detected as a USB Device, navigate to the Settings tab to configure your Device
(Network) settings. Selecting the Wifi option will require you to input your Wifi network
name and password. Enter this information and click Save to program the device.
If
this is a new device and you wish to register it to the SenseiAQ Cloud, click on the
Login tab. If you do not already have an account, click on Create Account.
Piera Systems Inc. reserves the right to make corrections, modifications enhancements, improvements and other changes to its products and
services at any time and to discontinue any product or service without notice. Please contact Piera Systems anytime to obtain the latest relevant
information - We are ready to help you determine which of our solutions will best meet your needs contact [e-mail] for information.
© 2021 Piera Systems Inc. Page | 5

When creating an account for the first time, be sure to input a valid email address in
case you later forget your password and need it reset. Note this email address will also
be used to send alerts on events and software updates from Piera Systems.
Login with your new account and you will be redirected to the Dashboard.
Piera Systems Inc. reserves the right to make corrections, modifications enhancements, improvements and other changes to its products and
services at any time and to discontinue any product or service without notice. Please contact Piera Systems anytime to obtain the latest relevant
information - We are ready to help you determine which of our solutions will best meet your needs contact [e-mail] for information.
© 2021 Piera Systems Inc. Page | 6

To register this (local USB) Device to your SenseiAQ Cloud account, click on “Register
device” Your device can now be accessed remotely via
https://sensei.pierasystems.com using this account.
Congratulations! Your Canāree is now ready to be deployed
as a standalone Air Quality Monitor. You can safely
disconnect the device from your PC and install it in its final
location. If you wish to register or configure additional
devices, connect them to SenseiAQ and follow the above
process to Register additional devices.
The device can be installed horizontally on a flat surface or
wall mounted vertically using the provided holes on the back
of the device (Distance between center holes is 2.25 inches.
This device is designed for indoor use only!
Piera Systems Inc. reserves the right to make corrections, modifications enhancements, improvements and other changes to its products and
services at any time and to discontinue any product or service without notice. Please contact Piera Systems anytime to obtain the latest relevant
information - We are ready to help you determine which of our solutions will best meet your needs contact [e-mail] for information.
© 2021 Piera Systems Inc. Page | 7

CLI Configuration using Terminal Software
Configuration of the Canāree i1 can also be done through CLI Configuration via the
provided USB-Adapter cable and your favorite Terminal Emulation Software for
Windows or MacOS such as PuTTY, HyperTerminal, Zterm or TerraTerm to access the
device via the USB-Serial port. If you're unsure of which tool to use, we recommend
PuTTY. https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html
Once connected via USB to your PC/Mac, Canāree will appear as a COM Port for use
with your terminal emulation software. The settings are 115200 bps / 8 / n / 1
Below is an example configuration for Wireless connectivity for you to modify and
paste into your device via Terminal emulation software if you prefer not to install
SenseiAQ.
%Wwifi=myWifiSSID,myWifiPASS
To Enable the Wired Ethernet port for network connectivity via DHCP and disable Wifi
%Wnetmode=1
To Disable the Wired Ethernet port for network connectivity and force Wifi Connectivity
%Wnetmode=0
[ Wait 20 seconds for the device to reboot ]
%Wwifi=myWifiSSID,myWifiPASS
[ The device will reboot once again and attempt the new Wifi connection ]
Piera Systems Inc. reserves the right to make corrections, modifications enhancements, improvements and other changes to its products and
services at any time and to discontinue any product or service without notice. Please contact Piera Systems anytime to obtain the latest relevant
information - We are ready to help you determine which of our solutions will best meet your needs contact [e-mail] for information.
© 2021 Piera Systems Inc. Page | 8

Other Useful CLI Commands
●%Rnetwork
Show network information (Including Static IPs and Network mode)
●%Rrssi
Show WiFi signal strength (Wireless Received Signal Strength Indicator (RSSI as
dbM)
●%Razure
Show Azure IoT Hub settings
●%Rrelay
Show WebRelay settings
●%Wreset
Reset device (soft power cycle)
Write Configuration Commands
●%Wnetmode=[0/1]
Set network mode. 0 for Wireless mode, 1 for Wired Ethernet
Example (set Wifi mode):
%Wnetmode=0
●%Wwifi=[ssid],[pass]
Set WiFi Network Name (SSID) and WPA2 / PSK (Pass)
Example:
%Wwifi=mywifi,pass123
●%Weth=[local_ip],[gateway_ip],[network_ip],[dns_ip],[dns2_ip]
Set ethernet options.
Piera Systems Inc. reserves the right to make corrections, modifications enhancements, improvements and other changes to its products and
services at any time and to discontinue any product or service without notice. Please contact Piera Systems anytime to obtain the latest relevant
information - We are ready to help you determine which of our solutions will best meet your needs contact [e-mail] for information.
© 2021 Piera Systems Inc. Page | 9

Example:
%Weth=192.168.0.71,192.168.0.1,192.168.0.0,8.8.8.8,8.8.4.4
●%Wautoreset=[0/10]
Set number of retries before auto-reset. Less than 5 not recommended to avoid restart
loop, 0 to disable auto-reset.
Example:
%Wautoreset=10
●%Wrelayactive=[0/1]
Toggle relay mode on or off.
Example:
%Wrelayactive=1
●%Wrelayurls=[relay_start_url],[relay_stop_url]
Set relay start and stop URLs.
Example:
%Wrelayurls=http://192.168.1.2/stateFull.xml?relayState=1,http://192.168.1.2/stateFull.x
ml?relayState=0
●%Wlimits=[pm1.0],[pm2.5],[pm10]
Set relay PM limits.
Example:
%Wlimits=35.5,35.5,155.0
Piera Systems Inc. reserves the right to make corrections, modifications enhancements, improvements and other changes to its products and
services at any time and to discontinue any product or service without notice. Please contact Piera Systems anytime to obtain the latest relevant
information - We are ready to help you determine which of our solutions will best meet your needs contact [e-mail] for information.
© 2021 Piera Systems Inc. Page | 10