Pilot Communications ANR7000BT User manual

BT-Link Controls
Volume Controls: You can independently adjust the volume for each ear
from your BT-Link.
Power Status/Button: Press and hold for one second to turn ON or OFF BT-
Link. LED indicates the power source and its status.
Bluetooth Status/Button: Press and hold for one second to turn ON or
OFF the Bluetooth. LED indicates the Bluetooth status. Additional phone
functions are available.
Aux Input: Use the provided 3.5 mm cable to connect to your audio source
without Bluetooth. When put the 3.5mm plug into the jack, there is a voice “line
in mode”, when set to line in mode, the bluetooth volume control also can
control the line in device volume
Audio Priority Switch: Controls how Aux audio and transmissions are
prioritized. Bluetooth Volume or next/previous song: Adjust your Bluetooth
device volume, or switch to next/previous songs
USB type C Input: Power your BT-Link via USB instead of through batteries.
Getting Started
Install batteries
Press on the battery box lid where indicated and slide the lid off. Insert two
AA batteries ensuring that the polarity is as shown. Slide the battery box lid
back on and you are ready to go.
ANR7000BT
BLUETOOTH and ANR
Operating Instructions
Powering On
To turn on, press the Power On button for more than
1 second and then let go.You will hear a voice say
“Power On”. If Power Button is pressed for more
than 3 seconds BT-Link will turn on and then off.
Bluetooth
To turn on Bluetooth press the Power Button for
more than 1 second and then let go. You will hear a
voice say “Power On”. If Power Button is pressed for
more than 3 seconds BT-Link will turn on and then off.
To turn off Bluetooth press the Power Button for
1 second and you will hear a voice say “Power OFF”.
Pairing
When you turn on Bluetooth the BT-Link will begin searching for a device
to pair with. Look for the Bluetooth name “BT-Link”. If prompted for a
code, enter 0000.
Pairing with 2nd device
To pair with a second device you must first disable the bluetooth function
of the first device. Now pair your second device and enable bluetooth
function of your first device. You should now have two devices paired.
Bluetooth Volume or next/previous song Control
On the side of BT-Link
Long press +/>| or -/|< to increase or decrease Bluetooth
volume. When you reach the Max or Min volume there is
a “DiDi” sound.
Short press +/>| or -/<| to switch to next/previous song.
Bluetooth Phone Functions
Press once to pick up a call
Press once to hang up a call
Press for more than 1 second to decline a call
Press twice quickly to redial the last call
Headset Volume
To adjust headset volume use the slide switches on front of
your BT-Link.
Audio Priority Modes
Use the Audio Priority switch to mute your auxiliary audio
input when you are sending or receiving radio transmissions.
AUTO: With incoming transmissions, Bluetooth and Aux are
muted and resume when transmission ends.
MIX: Aux and Bluetooth continue to play with transmissions.
OFF: Only transmissions are heard, Bluetooth and Aux are muted.
When set to Off Mode, in order to save battery power, the bluetooth is
POWERED OFF. When next switched to AUTO or MIX the bluetooth is
powered on again and will connect to your bluetooth devices in seconds.
Volume Control Power Status Aux Input Audio Priority Switch
Bluetooth Status
Bluetooth Volume
USB Input

ANR2888BT
ANR and Bluetooth
Operating Instructions
AUX IN: Use the 3.5mm cable to connect your
device to the AUX socket. Adjust the volume of your
AUX input from your device. Be sure to have the AUX
audio at a volume that ensures that you do not miss
any communications or aircraft alarms.
LED Colour Indicators
Main Power Button
Steady Green - BT-Link is powered via USB
Flashing Green - BT-Link is powered by battery
Orange - BT-Link has low battery
Flashing Red - BT-Link will turn off shortly
Bluetooth Button
Flashing Blue and Red - Searching for device
Blue Flash - Connected
Short Blue Flash - Call in Progress
Steady Blue - Aux 3.5mm Plug in as line in mode
MONO/STEREO Switch: The switch is located on the LEFT side in the
back of the battery box. For most general aviation aircraft the switch should
be set to Mono. If you only hear audio in one side, set the switch to Stereo.
AUTO SHUT OFF: With Auto Shut Off enabled and the BT-Link is not
connected to the intercom and there is no Aux or Bluetooth audio, it will
auto shut off in 5 minutes
If BT-Link is not connected to the intercom but there is Bluetooth or Aux
input, it will shut off in 60 minutes.
If BT-Link is connected to the intercom BT-Link will not automatically shut
off. You have the option to disable the Auto Shut Off feaure. The switch is
located on the RIGHT side in the back of the battery box.
ANR OPERATION
To place the microphone on the right or left of the head, simply rotate the
boom overhead.
With the headpad resting securely on the top of the head adjust the earcup
slides so that the earseals are centred over the ears.
For best noise cancellation, the microphone should be positioned 0-6mm
from the lips.
Insert the microphone plug (PJ068) into the aircraft or intercom microphone
jack and insert the phone plug (PJ055) into the aircraft or intercom phone
jack.
The volume controls are located on the control box. Slide the volume
controls to adjust the volume to a comfortable level.
There is a minature slide switch in the battery box to select stereo or mono.
The ANR2888BT is powered by the two 1.5v AA batteries in the control unit.
The ANR is turned on and off with the Bluetooth.
Distributed in Australia by
OZCOMM Australia Pty. Ltd. ABN. 56 106 963 320 trading as
Pilot Communications (Australia)
T: 07 5485 3016 P.O. Box 811
E: [email protected] Tewantin Qld., 4565,
W: pilotcommunications.com.au Australia
Sold with a 12 month REPLACEMENT Warranty
and 30 day money back guarantee