StarTech.com PEX867WAC22 User manual

Manual Revision: 05/08/2020
User Manual
For the latest information and specications visit
www.startech.com/PEX867WAC22
PCI Express to AC1200 Wireless-AC
Network Card
Actual product may vary from photos
SKU#: PEX867WAC22

1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Compliance Statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdi󱐯erentfromthatto
whichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003
du Canada. This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) This device
may not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.

2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for
an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body.
Déclaration d’exposition à la radiation:
Cet équipement respecte les limites d’exposition aux rayonnements IC dénies
pour un environnement non contrôlé. Cet équipement doit être installé et mis
en marche à une distance minimale de 20 cm qui sépare l’élément rayonnant de
votre corps.
L’émetteur ne doit ni être utilisé avec une autre antenne ou un autre émetteur ni
se trouver à leur proximité.
FCC ID:VYTLP-9094
IC:11232A-PEX867WAC22
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.

3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Wiringterminationsshouldnotbemadewiththeproductand/or
electriclinesunderpower.
• Cables(includingpowerandchargingcables)shouldbeplacedand
routedtoavoidcreatingelectric,trippingorsafetyhazards.
Mesures de sécurité
• Lesterminaisonsdecâblâgenedoiventpasêtree󱐯ectuéeslorsquele
produitet/oulescâblesélectriquessontsoustension.
• Lescâbles(ycomprislescâblesd’alimentationetdechargement)
doiventêtreplacésetacheminésdefaçonàévitertoutrisque
électrique,dechuteoudesécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでくださ
い。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回し
を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう
にしてください。
Misure di sicurezza
• Iterminialideilielettricinondevonoessererealizzateconilprodotto
e/olelineeelettrichesottotensione.
• Icavi(inclusiicavidialimentazioneediricarica)devonoessere
posizionatiestesiinmododaevitarepericolidiinciampo,rischidi
scosseelettricheopericoliperlasicurezza.
Säkerhetsåtgärder
• Monteringavkabelavslutningarfårintegörasnärproduktenoch/eller
elledningarnaärströmförda.
• Kablar(inklusiveelkablarochladdningskablar)skadrasochplaceraspå
såsättattriskförsnubblingsolyckorochandraolyckorkanundvikas.

4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Compliance Statements........................................................................1
Safety Statements..................................................................................3
Product Diagram ....................................................................................5
Product Information ..............................................................................6
Package Contents ..................................................................................................................................... 6
Requirements ............................................................................................................................................. 6
Hardware Installation............................................................................7
Installing the Low Prole Bracket........................................................................................................ 7
Hardware Installation .............................................................................................................................. 8
Attaching the Dual Band Antennas.................................................................................................... 9
Downloading the Driver......................................................................................................................... 9
Verifying Installation................................................................................................................................ 10
Operation ................................................................................................10
Specications..........................................................................................11

5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
Component Description
1LED Indicator • Flashing: Indicates
activity 2.4 to 5GHz.
2Antenna Connectors • Used to connect the
5 dBi Dual Band
Antennas to the
Network Card.
1
2
3

6
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
3PCIe Connector • Connects the Network
Card to the PCI Express
Slot on the Host
Computer.
Product Information
Package Contents
• PCI Express Wireless-AC Card x 1
• 5 dBi Dual Band Antennas x 2
• Antenna Stand x 1
• Low Prole Bracket x 1
• User Manual x 1
Requirements
For the latest requirements, please visit www.startech.com/
PEX867WAC22
• Computer with an available PCI Express® slot (x4, x8, or x16)
Tools
• Small Phillips® Head Screwdriver
OS
• Windows® 8, 7, Vista, or XP
• Windows Server® 2012, 2008 R2, or 2003

7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Hardware Installation
Installing the Low Prole Bracket
By default the Full Prole Bracket is attached to the Network
Card. Depending on your system conguration you may need
to remove the Full Prole Bracket and replace it with the Low
Prole Bracket (included).
1. Using a Small Phillips Head Screwdriver (sold separately),
remove the two Bracket Screws securing the Full Prole
Bracket to the Network Card.
2. Align the Screw Holes on the Network Card with the Screw
Holes on the Low Prole Bracket. Making sure the Network
Card is sitting on top of the Screw Holes on the Low Prole
Bracket.
3. Insert the Bracket Screws through the Network Card and
into the Screw Holes on the Low Prole Bracket.
4. Using the Small Phillips Head Screwdriver, tighten the
Bracket Screws, being careful not to over-tighten.

8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Hardware Installation
Warning: Network cards can be damaged by static elec-
tricity. Make sure that you are properly grounded before
you open the computer case or touch the Network Card.
You should wear an anti-static strap when you install any
computer components. If an anti-static strap is not available,
discharge any built-up static electricity by touching a large
grounded metal surface for several seconds. Only handle
the Network Card by its edges and do not touch the gold
connectors.
1. Turn o the Computer and disconnect any Peripheral
Devices that are connected (e.g. printers, external hard
drives, etc.).
2. Unplug the Power Cable from the back of the Computer.
3. Remove the Cover from the Computer Case.
Note: Consult the documentation that came with the Com-
puter for details on how to remove the cover safely.
4. Locate an open PCI Express Slot (x4, x8, or x16) and remove
the corresponding Metal Cover Plate from the back of the
Computer Case.
5. Gently insert the Network Card into the open PCI Express
Slot and fasten the Bracket to the back of the Computer
Case.
6. (Optional) Connect a 15 Pin SATA Power Connector from
the Power Supply to the SATA Power Connector on the
Network Card.

9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
7. Place the Cover back onto the Computer Case.
8. Reconnect all of the Peripheral Devices that were
disconnected in step 1.
9. Place the Cover back onto the Computer Case.
10. Reconnect the Power Cable to the back of the Computer.
Attaching the Dual Band Antennas
1. Screw the 5 dBi Dual Band Antennas onto the Antenna
Connectors on the sides of the Antenna Stand.
2. Screw the Antenna Cables on the Antenna Stand to the
Antenna Connectors on the Network Card.
- or -
3. Screw the 5 dBi Dual Band Antennas directly to the
Antenna Connectors on the Network Card.
Downloading the Driver
When the Network Card is installed the drivers should install
automatically. If the drivers do not automatically install,
navigate to www.startech.com/PEX867WAC22 to download
the appropriate driver package.
1. Click on the Support tab, under Drivers, select the
appropriate driver package for the Operating System
running on the Host Computer.
2. When you have downloaded and unzipped the driver. Click
on the Installation Guide PDF and follow the instructions.