Pilz PSSu E PS-P +/-10V User manual

PSSu E PS-P +/-10V
Operating Manual 21921-EN-03
}Decentralised system PSSuniversal I/O

Preface
This document is a translation of the original document.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes. Suggestions and comments for improving this documentation will be
gratefully received.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital

Contents
Operating Manual PSSu E PS-P +/-10V
21921-EN-03 3
Section 1 Introduction 5
1.1 Validity of documentation 5
1.1.1 Retaining the documentation 5
1.2 Definition of symbols 5
Section 2 Overview 7
2.1 Module structure 7
2.2 Module features 7
2.3 Front view 8
Section 3 Safety 10
3.1 Intended use 10
3.2 Safety regulations 11
3.2.1 Use of qualified personnel 11
3.2.2 Warranty and liability 11
3.2.3 Disposal 11
Section 4 Function description 12
4.1 Block diagram 12
4.2 Module features 12
4.2.1 Integrated protection mechanisms 12
4.2.2 Functions 12
4.3 Configuration 13
Section 5 Installation 14
5.1 General installation guidelines 14
5.1.1 Dimensions 14
5.2 Installing the base module 16
5.3 Inserting and removing an electronic module 17
5.3.1 Inserting an electronic module 18
5.3.2 Removing an electronic module 19
5.3.3 Changing an electronic module during operation 19
Section 6 Wiring 20
6.1 General wiring guidelines 20
6.1.1 Mechanical connection of the base modules 20
6.2 Terminal configuration 22
Section 7 Operation 24
7.1 Messages 24
7.2 Display elements 24
7.2.1 Display elements for module diagnostics 24
Section 8 Technical details 25

Contents
Operating Manual PSSu E PS-P +/-10V
21921-EN-03 4
Section 9 Order reference 27
9.1 Product 27
9.2 Accessories 27

Introduction
Operating Manual PSSu E PS-P +/-10V
21921-EN-03 5
1 Introduction
1.1 Validity of documentation
This documentation is valid for the product PSSu E PS-P +/-10V. It is valid until new docu-
mentation is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
1.1.1 Retaining the documentation
This documentation is intended for instruction and should be retained for future reference.
1.2 Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.

Introduction
Operating Manual PSSu E PS-P +/-10V
21921-EN-03 6
INFORMATION
This gives advice on applications and provides information on special fea-
tures.

Overview
Operating Manual PSSu E PS-P +/-10V
21921-EN-03 7
2 Overview
2.1 Module structure
A module consists of
}Electronic module and
}Base module with
– Screw terminals or
– Cage clamp terminals
The base modules are the carrier units for the electronic modules and are used to connect
the field wiring. The electronic modules are inserted on to the base modules and determine
the module's function.
Details of the base modules that can be used are available in the chapter entitled “Intended
Use”.
2.2 Module features
The product has the following features:
}Primary side of power supply
– The external supply is fed to the base module terminals.
– Voltage: 24V
}Secondary side of power supply
– The module supplies the output voltage to the base module terminals.
– No buffer when the supply voltage is interrupted
– Voltage: 10 V/-10 V
– Max. continuous output: 10,0 W
– Max. current at 10 V: 1,0 A
– Max. current at -10 V: 0,50 A
}LED for:
– External voltage

Overview
Operating Manual PSSu E PS-P +/-10V
21921-EN-03 8
2.3 Front view
2111
2212
2313
2414
11
0V
21
0V
12
0V
22
0V
13 23
14 24
PSSu E
PS-P+/-10V
-10V+10V
PSSu E
PS-P +/-10V
312591
000000
001
(C) (C)
-10V +10V 1
3
8
7
4
5
6
10
2
11
9
A
B
Key:
}A: Electronic module
}B: Base module
}1: LED for module diagnostics
}2: Labelling strip with:
– Name of electronic module
– Order number
– Serial number
– Hardware version number
– 2D code
}3: Labelling strip for the terminal configuration on the base module
}4: Name of electronic module
}5: Connection level 1
}6: Connection level 2
}7: Connection level 3
}8: Connection level 4

Overview
Operating Manual PSSu E PS-P +/-10V
21921-EN-03 9
}9: Square mounting holes (connection levels 1, 2, 3 and 4)
– With screw to loosen/tighten the screw terminal on base modules with screw termin-
als
– With mechanism to operate the cage clamp on base modules with cage clamp ter-
minals
}10: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal
lines
}11: Mounting slot for colour marker to label the connection level (connection levels 1, 2,
3 and 4)

Safety
Operating Manual PSSu E PS-P +/-10V
21921-EN-03 10
3 Safety
3.1 Intended use
The module may be used to convert a 24 V protective extra low voltage, in order to supply
sensors and actuators connected to the PSSuniversal system.
Intended use includes making the electrical installation EMC-compliant. Please refer to the
guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use
in an industrial environment. It is not suitable for use in a domestic environment, as this can
lead to interference.
The following is deemed improper use in particular:
}Any component, technical or electrical modification to the module
}Use of the module outside the areas described in this manual
}Any use of the module that is not in accordance with the technical details.
INFORMATION
The module is supported by
}PSSuniversal Configurator and PSSuniversal Assistant from Version
1.5.0
}PAS4000 from Version 1.1.1
– We recommend that you always use the latest version (download
from www.pilz.de).
The PSSu E PS-P +/-10V module may be used in conjunction with the following base mod-
ules:
}PSSu BP 1/8 S
}PSSu BP 1/8 C
}PSSu BP 1/12 S
}PSSu BP 1/12 C
}PSSu BP-C1 1/12 S
}PSSu BP-C1 1/12 C