PIONEER DJ DJM-V10 User manual

1
Quick-Start Guide
Pioneer DJ DJM-V10

2
Setup
Serato Software
The Pioneer DJ DJM-V10 is a “Paid upgrade to Serato DJ Pro” device, meaning it requires a stand-alone
Serato DJ license to  used with Serato DJ Pro. This can  purchased by itself, or alongside the Serato DVS
expansion, bundled as the Serato DJ Club Kit. Find out more, here.
Please ensure you have the latest version of Serato DJ Pro installed:
Click here to download Serato DJ Pro
Driver Software
The Pioneer DJ DJM-V10 requires manufacturer specific drivers on both Mac & Windows operating
systems. You must download and install the driver from Pioneer’s website, here.
Audio Routing
Head over to Setup --> Audio in Serato DJ Pro and choose Primary decks 1 & 3 to assign Serato’s virtual decks
1 & 2 to channels 1 & 3 on the mixer. Virtual decks 3 & 4 will assign to channels 4 & 6 on the mixer.
Alternatively choose Primary decks 3 & 4 to assign Serato’s virtual decks 1 & 2 to channels 3 & 4 on the mixer.
Virtual decks 3 & 4 will assign to channels 1 & 6 on the mixer.
Overview
#DJM-V10 Control FUNCTION
1POWER SWITCH Turn on mixer
2 SEND/RECEIVE Connect TRS jack for send & receive input/output respectively
3 PHONO/LINE INPUT 1/2/3/4/5/6 Connect LINE or PHONO input
4 GROUND POST Connect ground wire from turntables
5 MIC 1 & 2 Connect XLR or TRS microphone input
6 KENSINGTON LOCK Attach a Kensington lock
7MIDI OUT Connect MIDI device
8LINK Connect Link-compatible device via RJ45 connection
9DIGITAL INPUT Connect Digital Input
10 DIGITAL MASTER OUT Connect Digital Master output via XLR
11 BOOTH Connect Booth output via TRS
12 MASTER 1 & 2 Connect Master output via XLR or Unbalanced RCA
13 RECORD OUT Connect RCA cable for Record Output
14 AC IN Connect AC power cable
1 52 3 4
810 911121314 7 6

3
Overview
1 2 4 53
6
17
7
1112 10 98
14
13
16
15

4
# DJM - V10
CONTROL
FUNCTION
1USB 1 & USB 2 Connect USB cable to computer(s)
2 CHANNEL USB & INPUT SELECT Input source & USB 1/2 select per channel
3 MIXER EQ SECTION Adjust EQ controls for each channel
4 MASTER OUTPUT LEVEL Master output level
5 MASTER ISOLATOR Hardware dedicated Master Isolator controls
6 MULTI I/O SECTION Hardware dedicated Multi I/O controls
7MIXER FX SECTION Hardware BPM FX
8BOOTH LEVEL & EQ Booth output level and EQ section
9HEADPHONE B SECTION Headphone B level controls
10 CHANNEL FADER AND CUE Channel volume and headphone cue select
11 CROSSFADER ASSIGN Assign per channel A/Thru/B
12 CROSSFADER Crossfader tween channel A/B
13 HEADPHONE A SECTION Headphone A level controls
14 SEND SECTION Hardware dedicated Send controls
15 FILTER SECTION Hardware dedicated Filter controls
16 MIC SECTION Adjust Mic level, tone & EQ
17 HEADPHONE INPUT Connect headphones via 1/8” or 1/4” port
Overview
DVS
The Pioneer DJ DJM-V10 is ‘paid upgrade to Serato DVS hardware’, meaning it requires activation of a Serato
DVS license to allow you to use turntables or CD players to control Serato DJ Pro using NoiseMap™ Control
Tone. Serato DVS is purchased separately and then requires activation.
You can find out more and purchase DVS, by visiting our website here.
Setup
Enable the DVS expansion pack in Serato DJ Pro via Setup --> Expansion packs --> Vinyl/CD control, then
connect your Pioneer DJ DJM-V10 via USB to your computer, connect your turntables or other PHONO device
to the PHONO inputs on the back of the mixer, or CD/Media players to the LINE inputs on the back of the mixer.
Set the Input Source select near the top of each respective channel to ‘DVS’, and the USB selector to the
respective USB port the computer you’re using is connected to.
Head over to Setup --> Audio in Serato DJ Pro, and choose TURNTABLES for PHONO devices, or CDs for
LINE devices, under Deck Setup.
You can find the full DVS setup instructions on our website here.

5
MIDI
The MIDI feature in Serato DJ Pro provides the ability to remap Serato DJ Pro software functions to your
primary Serato controller, interface or mixer. You can also assign controls to a secondary MIDI controller to
further enhance your performance.
For more information on MIDI mapping with Serato DJ Pro click here
To remap your supported Serato device, open the SETUP screen and click the MIDI tab. If your Serato
device supports hardware remapping, it will show up in the MIDI Devices list at the top.
Select your connected device from the MIDI Devices list and make sure the “Allow Serato Hardware
Remapping” option is checked.
Once checked, the MIDI assign button at the top of the screen will come available for you to start
remapping.
You can save, edit or delete MIDI presets in the MIDI tab of the SETUP screen. Clicking ‘Restore Defaults’
will erase any custom mappings for all connected devices and revert their functions back to default.
Help
Show Tooltips
Click on the button in the upper right-hand corner of Serato DJ Pro, then to enable
tooltips. Tool tips provide a handy way to learn the various features of Serato DJ Pro.
Move the mouse over a section of the screen to bring up a context sensitive tool tip.
Watch Tutorials
Click on the button in the upper right-hand corner of Serato DJ Pro, then to launch
your default internet browser and watch tutorials, to help you get familiar with Serato DJ Pro.
Get Support
Click on the button in the upper right-hand corner of Serato DJ Pro, then to launch your
default internet browser and navigate to the Serato DJ Pro knowledge base, where you can find helpful
articles and guides on Serato DJ Pro. Alternatively, type in the box, with keywords, to
search the Serato DJ Pro knowledge base for specific, related topics.