PIONEER DJ DJM-S3 User manual

PIONEER
DJM-S3
QUICKSTART
GUIDE

Installation and Setup
The Pioneer DJ DJM-S3 is a Serato DJ and DVS enabled device and does
not require aditional Serato DJ or DVS Expansion Pack licenses.
The DJM-S3 requires drivers on both Mac OS X and Windows. Please
make sure you have the latest drivers installed before using with Serato DJ.
It is always important to connect your mixer directly to your computer,
rather than a USB hub. Please also ensure you have installed the latest
version of Serato DJ from http://serato.com/dj/downloads
Follow the steps in the DVS Control section to use the DJM-S3 with DVS
control and Serato DJ.
NOTE: After the driver is installed, you will need to restart the mixer before
the it will connect correctly. Please restart your mixer after installing the
driver and using your DJM-S3 for the rst time.
DVS Control
Follow the steps below to get the DJM-S3 set up with Serato DJ DVS
control.
1. Install Drivers
Connect your DJM-S3 mixer via USB and open the latest version of Serato
DJ. You should see an ‘INSTALL DRIVER’ dialogue box appear in the right
hand side-panel. Click ‘INSTALL DRIVER’ and follow the installer prompts.
Once the driver has been installed, turn your mixer OFF and then ON.
NOTE: Make sure the mixer is restarted after the driver is installed. This is
required before the mixer will function correctly with Serato DJ.
If you don’t have the mixer with you right now you can still download the
driver from the hardware manufacturers website.
2. Select Input source
Once turntables or CDJs are connected, open the SETUP screen and click
the AUDIO tab. Click Depending on what kind of input you have connected
(Turntables/CDJs) you will need to make sure this is set accordingly for
each channel. Click the conguration you want to use.
NOTE: If you do not set the mixer’s input accordingly, DVS control will not
work. Please make sure you have clicked the appropriate input source.

5 10
7
6
8
9
4 11
3 12
14
16
1
2
13
15
17
18
MIXER

#DJM-S3 Control Function
1 FILTER Channel combo lter (lowpass/highpass)
2 PARAMETER Adjust Parameter/amount
3 MIC TONE Adjust MIC Tone
4 MIC LEVEL Adjust MIC Level
5 AUX IN TRIM Adjust Aux input volume
6 AUX IN INPUT SELECT Toggle Aux input source
7 CHANNEL EQ 3-band Channel EQ
8 CHANNEL TRIM Adjust Channel volume
9 CHANNEL INPUT SELECT Toggle Channel input source
10 MASTER VOLUME Adjust Master output volume
11 HEADPHONES MIX Adjust Headphones mix
12 HEADPHONES LEVEL Adjust Headphones output volume
13 FILTER Channel Filter on/off
14 CHANNEL CUE Enable Channel headphone cue
15 CROSSFADER CURVE Adjust Crossfader curve
16 CHANNEL FADER Adjust Channel volume
17 CROSSFADER REVERSE Reverse Crossfader channels
18 CROSSFADER Fade audio between channels A-B
NOTE: The SHIFT button is used with other buttons that have shift modier functions.

#DJM-S3 Control Function
1 POWER Turn unit On/Off
2 AC IN Connect AC power
3 MASTER OUTPUT 2 RCA output
4 MASTER OUTPUT 1 Balanced XLR output
5 CH 2 INPUT Ch 2 Phono/Line Inputs
6 CH 1 INPUT Ch 1 Phono/Line Inputs
7 AUX IN RCA Aux Input
8 MIC IN Connect Microphone
9 USB Connect via USB to computer
10 HEADPHONE OUTPUT 1/4”/1/8” Headphone Output
10
34
18
579
26

MIDI
The MIDI feature in Serato DJ provides the ability to remap Serato DJ
software functions to your primary Serato DJ controller, interface or mixer.
You can also assign controls to a secondary MIDI controller to further
enhance your performance.
For more information on MIDI mapping with Serato DJ click here.
To remap your supported Serato DJ device, open the SETUP screen and
click the MIDI tab. If your Serato DJ device supports hardware remapping
it will show up in the MIDI Devices list at the top.
Select your connected device from the MIDI Devices list and make sure the
“Enable MIDI device” option is checked.
Once checked, the MIDI assign button at the top of the screen will become
available for you to start remapping.
You can save, edit or delete MIDI presets in the MIDI tab of the SETUP
screen. Clicking ‘Restore Defaults’ will erase any custom mappings for all
connected devices and revert their functions back to default.
Download the Serato DJ software manual for further information.
NOTE: Ofcial Serato Accessories do not currently support user remapping.
Hardware features that cannot be remapped at this stage are Jog wheels/
Platters, Input Switches, Shift buttons and Performance Pad Mode buttons.
Using the Tool Tips
Click on the icon to enable Tool Tips. This is located in between the
MIDI and setup button in the top right hand corner of the screen. Tool Tips
provide a handy way to learn the various features of Serato DJ.
Move the mouse over a section of the screen to bring up a context sensitive
tool tip. Holding the mouse over the button with Tool Tips turned on
will show you a list of all keyboard shortcuts.
For more information about how to use Serato DJ, please go to our website
www.serato.com or refer to the Serato DJ Software Manual. For more
information on your controller, please refer to the hardware manual.
For further help please contact [email protected] or go to
www.serato.com/dj/support