Pioneer XDJ-RX User manual

ORDER NO.
PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION
2015
2015 Printed in Japan
XDJ-RX
RRV4592
DJ SYSTEM
XDJ-RX
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
XDJ-RX LSYXJ8 AC 110 V to 240 V
XDJ-RX UXJCB AC 110 V to 240 V
XDJ-RX AXJ5 AC 110 V to 240 V
K-MZV MAR.

2XDJ-RX
12 3 4
A
B
C
D
E
F
12 3 4
SAFETY INFORMATION
WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
harm.
Health & Safety Code Section 25249.6 - Proposition 65
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120 V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the protection
afforded by them necessarily can be obtained by using
replacement components rated for voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this Service Manual.
Electrical components having such features are
identified by marking with a >on the schematics and on
the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER Service
Manual. A subscription to, or additional copies of,
PIONEER Service Manual may be obtained at a nominal
charge from PIONEER.
Leakage
current
tester
Reading should
not be above
0.5 mA
Device
under
test
Test all
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter
plug as required)
Earth
ground
AC Leakage Test
(FOR USA MODEL ONLY)

3
XDJ-RX
56 7 8
56 7 8
A
B
C
D
E
F
CONTENTS
SAFETY INFORMATION.......................................................................................................................................................... 2
1. SERVICE PRECAUTIONS .................................................................................................................................................... 5
1.1 NOTES ON SOLDERING ............................................................................................................................................... 5
1.2 NOTES ON REPLACING ............................................................................................................................................... 5
1.3 SERVICE NOTICE.......................................................................................................................................................... 5
2. SPECIFICATIONS................................................................................................................................................................. 6
3. BASIC ITEMS FOR SERVICE .............................................................................................................................................. 7
3.1 CHECK POINTS AFTER SERVICING ........................................................................................................................... 7
3.2 JIGS LIST ....................................................................................................................................................................... 7
3.3 PCB LOCATIONS ........................................................................................................................................................... 8
4. BLOCK DIAGRAM .............................................................................................................................................................. 10
4.1 OVERALL WIRING DIAGRAM (1/2) ............................................................................................................................. 10
4.2 OVERALL WIRING DIAGRAM (2/2) ............................................................................................................................. 12
4.3 SIGNAL BLOCK DIAGRAM (CHASSIS SECTION)...................................................................................................... 14
4.4 SIGNAL BLOCK DIAGRAM (PANEL SECTION) .......................................................................................................... 16
4.5 POWER BLOCK DIAGRAM ......................................................................................................................................... 18
5. DIAGNOSIS ........................................................................................................................................................................ 20
5.1 STARTUP SEQUENCE ................................................................................................................................................ 20
5.2 TROUBLESHOOTING.................................................................................................................................................. 21
5.3 SIMPLIFIED DIAGNOSTIC PROCEDURE FOR AUDIO SIGNAL................................................................................ 30
5.4 VOLTAGE MONITORING CIRCUIT .............................................................................................................................. 31
5.5 ABOUT PROTECTOR .................................................................................................................................................. 33
5.6 METHOD FOR CONNECTION CONFIRMATION OF THE LAN (LINK) PORT............................................................ 34
5.7 IC INFORMATION ........................................................................................................................................................ 35
6. SERVICE MODE ................................................................................................................................................................. 36
6.1 TEST MODE................................................................................................................................................................. 36
6.2 ABOUT THE DEVICE................................................................................................................................................... 42
7. DISASSEMBLY ................................................................................................................................................................... 43
8. EACH SETTING AND ADJUSTMENT ................................................................................................................................ 59
8.1 NECESSARY ITEMS TO BE NOTED........................................................................................................................... 59
8.2 UPDATING OF THE FIRMWARE ................................................................................................................................. 60
8.3 ADJUSTMENT METHOD FOR ROTATION LOAD OF THE JOG DIALS ..................................................................... 61
8.4 USER SETABLE ITEMS ............................................................................................................................................... 62
9. EXPLODED VIEWS AND PARTS LIST............................................................................................................................... 64
9.1 PACKING SECTION ..................................................................................................................................................... 64
9.2 BOTTOM SECTION...................................................................................................................................................... 66
9.3 CHASSIS SECTION ..................................................................................................................................................... 68
9.4 CONTROL PANEL SECTION (1/3)............................................................................................................................... 70
9.5 CONTROL PANEL SECTION (2/3)............................................................................................................................... 72
9.6 CONTROL PANEL SECTION (3/3)............................................................................................................................... 74
9.7 JOG DIAL SECTION .................................................................................................................................................... 76
9.8 LCD SECTION.............................................................................................................................................................. 78
10. SCHEMATIC DIAGRAM.................................................................................................................................................... 80
10.1 MAIN ASSY (1/16)...................................................................................................................................................... 80
10.2 MAIN ASSY (2/16)...................................................................................................................................................... 82
10.3 MAIN ASSY (3/16)...................................................................................................................................................... 84
10.4 MAIN ASSY (4/16)...................................................................................................................................................... 86
10.5 MAIN ASSY (5/16)...................................................................................................................................................... 88
10.6 MAIN ASSY (6/16)...................................................................................................................................................... 90
10.7 MAIN ASSY (7/16)...................................................................................................................................................... 92
10.8 MAIN ASSY (8/16)...................................................................................................................................................... 94
10.9 MAIN ASSY (9/16)...................................................................................................................................................... 96
10.10 MAIN ASSY (10/16).................................................................................................................................................. 98
10.11 MAIN ASSY (11/16)................................................................................................................................................ 100
10.12 MAIN ASSY (12/16)................................................................................................................................................ 102
10.13 MAIN ASSY (13/16)................................................................................................................................................ 104
10.14 MAIN ASSY (14/16)................................................................................................................................................ 106
10.15 MAIN ASSY (15/16)................................................................................................................................................ 108
10.16 MAIN ASSY (16/16)................................................................................................................................................ 110
10.17 JACK1 ASSY (1/2).................................................................................................................................................. 112
10.18 JACK1 ASSY (2/2).................................................................................................................................................. 114
10.19 JACK2 ASSY (1/3).................................................................................................................................................. 116
10.20 JACK2 ASSY (2/3).................................................................................................................................................. 118

4XDJ-RX
12 3 4
A
B
C
D
E
F
12 3 4
10.21 JACK2 ASSY (3/3) ..................................................................................................................................................120
10.22 HPJB and MICT ASSYS .........................................................................................................................................122
10.23 USB1 and USB2 ASSYS ........................................................................................................................................123
10.24 USBP1 ASSY..........................................................................................................................................................124
10.25 USBP2 ASSY..........................................................................................................................................................126
10.26 EXTB ASSY (1/3)....................................................................................................................................................128
10.27 EXTB ASSY (2/3)....................................................................................................................................................130
10.28 EXTB ASSY (3/3)....................................................................................................................................................132
10.29 DPNL1 and DPNL2 ASSYS ....................................................................................................................................134
10.30 MIXB ASSY (1/4) ....................................................................................................................................................136
10.31 MIXB (2/4), CRFB and CHF1 ASSYS.....................................................................................................................138
10.32 MIXB ASSY (3/4) ....................................................................................................................................................140
10.33 MIXB ASSY (4/4) ....................................................................................................................................................142
10.34 LLED ASSY.............................................................................................................................................................144
10.35 CDJB ASSY (1/3)....................................................................................................................................................146
10.36 CDJB ASSY (2/3)....................................................................................................................................................148
10.37 CDJB ASSY (3/3)....................................................................................................................................................150
10.38 PNL1 ASSY.............................................................................................................................................................152
10.39 PNL2 ASSY.............................................................................................................................................................154
10.40 JOGT1 and JOGR1 ASSYS....................................................................................................................................156
10.41 JOGT2 and JOGR1 ASSYS....................................................................................................................................158
10.42 JLED1 ASSY...........................................................................................................................................................160
10.43 JLED2 ASSY...........................................................................................................................................................162
10.44 POWER SUPPLY ASSY .........................................................................................................................................164
10.45 VOLTAGES..............................................................................................................................................................166
10.46 WAVEFORMS .........................................................................................................................................................167
11. PCB CONNECTION DIAGRAM ......................................................................................................................................170
11.1 MAIN ASSY...............................................................................................................................................................170
11.2 JACK1, JACK2, HPJB and MICT ASSYS .................................................................................................................174
11.3 USB1, USB2, USBP1 and USBP2 ASSYS...............................................................................................................178
11.4 EXTB, DPNL! And DPNL2 ASSYS ...........................................................................................................................180
11.5 MIXB, CRFB, CHF1 and LLED ASSYS ....................................................................................................................184
11.6 CDJB, PNL1 and PNL2 ASSYS ................................................................................................................................188
11.7 JOGT1, JOGT2, JOGR1, JLED1 and JLED2 ASSYS ..............................................................................................192
11.8 POWER SUPPLY ASSY ...........................................................................................................................................196
12. PCB PARTS LIST ............................................................................................................................................................197

5
XDJ-RX
56 7 8
56 7 8
A
B
C
D
E
F
1. SERVICE PRECAUTIONS
1.1 NOTES ON SOLDERING
1.2 NOTES ON REPLACING
1.3 SERVICE NOTICE
• For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
• Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 ºC.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 ºC in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Do NOT use a soldering iron whose tip temperature cannot be controlled.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts:
• Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.
The part listed below is difficult to replace as a discrete component part.
When the part listed in the table is defective, replace whole Assy.
Assy Name
MAINAssy
USBP1 Assy/
USBP2 Assy
EXTB Assy
DC-DC CONVERTER (for system power)BD9328EFJ IC with heat-padIC102, IC105
DC-DC CONVERTER (for audio power)BD9851EFVIC with heat-padIC401, IC402
PO SUPPLY IC (Power management IC)MMPF0100F0AEP QFNIC with heat-padIC602
U-PRO IC (Application processor)MCIMX6U6AVM08AC BGAIC1001
RAM IC (DDR3)K4B1G1646G-BCK0 BGAIC1201, IC1301
INTERFACE IC (LANPHY)LAN8720A-CP QFNIC with heat-padIC1401
INTERFACE IC (USB HUB)USB2512B-AEZG-TR QFNIC with heat-padIC1801
DC-DC CONVERTER (for USB power supply)BD9328EFJ IC with heat-padIC8101, IC8301
High-side SWIC (for USB current control)TPS2557DRB IC with heat-padIC8102, IC8302
DC/DC CONV IC (for display power)R1290K103A QFNIC with heat-padIC8601
DRIVER IC (for LCD back right)BD81A04EFV-M IC with heat-padIC8701
Parts that is Difficult to Replace
Ref No. FunctionPart No. Remarks
About the Flash ROM (IC1501) in the MAIN Assy
Replacement of the Flash ROM (IC1501: DYW1864 (first release)) in the MAINAssy is not possible during service, because
writing of the MAC address on the production line is required.
Therefore, the Flash ROM (IC1501) is not supplied as a service part. If the Flash ROM is defective, replace the whole MAINAssy.

6XDJ-RX
12 3 4
A
B
C
D
E
F
12 3 4
2. SPECIFICATIONS
Power requirements....................... AC 110 Vto 240 V, 50 Hz/60 Hz
Power consumption ..................................................................35 W
Power consumption (standby) ................................................0.4 W
Main unit weight........................................................8.0 kg (17.6 lb)
Max. external dimensions.........728.2 mm (W) × 104.2 mm (H) × 411.9 mm (D)
(28.7 in. (W) × 4.1 in. (H) × 16.2 in. (D))
Tolerable operating temperature........... +5 °C to +35 °C (+41 °F to +95 °F)
Tolerable operating humidity............5 % to 85 % (no condensation)
Audio Section
Sampling rate .....................................................................44.1 kHz
A/D, D/A converter................................................................. 24 bits
Frequency characteristic
USB, LINE/PHONO, MIC1, MIC2 ........................ 20 Hz to 20 kHz
S/Nratio (rated output, A-WEIGHTED)
USB ................................................................................... 111 dB
LINE/PHONO ...................................................................... 97 dB
MIC...................................................................................... 84 dB
Total harmonic distortion (20 Hz — 20 kHzBW)
USB ..................................................................................0.002 %
LINE/PHONO ...................................................................0.004 %
Standard input level / Input impedance
LINE/PHONO ........................................................–12 dBu/47 kΩ
MIC.......................................................................–52 dBu/8.5 kΩ
Standard output level / Load impedance / Output impedance
MASTER1......................................... +6 dBu/10 kΩ/390 Ωor less
MASTER2......................................... +2 dBu/10 kΩ/820 Ωor less
BOOTH ............................................. +6 dBu/10 kΩ/390 Ωor less
PHONES .............................................. +8dBu/32 Ω/10 Ωor less
Rated output level / Load impedance
MASTER1................................................................24 dBu/10 kΩ
MASTER2................................................................20 dBu/10 kΩ
Crosstalk
LINE/PHONO ...................................................................... 82 dB
Channel equalizer characteristic
HI.......................................................... –26 dB to +6 dB (13 kHz)
MID......................................................... –26 dB to +6 dB (1 kHz)
LOW....................................................... –26 dB to +6 dB (70 Hz)
Microphone equalizer characteristic
HI........................................................ –12 dB to +12 dB (10 kHz)
LOW................................................... –12 dB to +12 dB (100 Hz)
Input / Output terminals
LINE/PHONO terminals
RCA pin jack........................................................................ 2 sets
MIC1 terminal
XLR connector/phone jack (Ø 6.3 mm) ................................. 1 set
MIC2 terminal
Phone jack (Ø 6.3 mm).......................................................... 1 set
MASTER1 terminals
XLR connector....................................................................... 1 set
MASTER2 terminals
RCA pin jacks........................................................................ 1 set
BOOTH OUT terminals
Phone jack (Ø 6.3 mm).......................................................... 1 set
PHONES terminals
Stereo phone jack (Ø 6.3 mm) .............................................. 1 set
Stereo mini phone jack (Ø 3.5 mm)....................................... 1 set
USB terminal
A type .................................................................................. 2 sets
B type .................................................................................... 1 set
• Be sure to use the [MASTER1] terminals only for a balanced
output. Connection with an unbalanced input (such as RCA)
using an XLR to RCA converter cable (or converter adapter), etc.,
may lower the sound quality and/or result in noise.
For connection with an unbalanced input (such as RCA), use the
[MASTER2] terminals.
• The specifications and design of this product are subject to
change without notice.
• Power cord
(LSYXJ8: ADG1244)
(UXJCB: DDG1108)
(AXJ5: DDG1114)
• LANcable
(DDE1141)
• Warranty (LSYXJ8only)
• Operating instructions ( Qick start guide)
(LSYXJ8: DRH1293, DRH1294)
(UXJCB: DRH1292)
(AXJ5: DRH1299)
• Software information
(DRH1305)
Accessories

7
XDJ-RX
56 7 8
56 7 8
A
B
C
D
E
F
3. BASIC ITEMS FOR SERVICE
3.1 CHECK POINTS AFTER SERVICING
3.2 JIGS LIST
Items to be checked after servicing
To keep the product quality after servicing, confirm recommended check points shown below.
Distortion
Noise
Volume too low
Volume too high
Volume fluctuating
Sound interrupted
See the table below for the items to be checked regarding audio.
Item to be checked regarding audio
No. Procedure Check points
1Confirm the firmware version. The version of the firmware must be latest.
Update firmware to the latest one, if it is not the latest.
2Confirm whether the customer complain has been solved. The customer complain must not be reappeared.
Audio and operations must be normal.
3 Check the analog audio output. There must be no errors in audio output and operations of each channel.
4 Check playback, using the fader function. There must be no errors in audio output and operations of each channel.
5 Check the MASTER output. Audio and operations must be normal.
6 Check the headphones output. There must be no errors, such as noise, in the audio output.
Audio, Search and operations must be normal.
8 Check the appearance of the product. No scratches or dirt on its appearance after receiving it for service.
7Check the connection of each interface.
Playback data contained in the device connected to USB A.
The PC must be linked.USB B.
The rekordbox software must be linked.Playback the library data of the PC via LAN.
Lubricants and Glues List
Name Part No. Remarks
Lubricating oil GYA1001 Refer to "9.5 CONTROL PANEL SECTION(2/3)",
"9.7 JOG DIAL SECTION".

8XDJ-RX
12 3 4
A
B
C
D
E
F
12 3 4
3.3 PCB LOCATIONS
A
MAINASSYHLD3 ASSY
D
HPJB ASSY
N
CRFB ASSY
O
CHF1 ASSY
U
JOGT2 ASSY
T
JOGT1 ASSY
O
CHF1 ASSY
L
DPNL2 ASSY
G
USB2 ASSY
I
USBP2 ASSY
W
JLED1 ASSY
HLD1 ASSY
V
JOGR1 ASSY
K
DPNL1 ASSY
X
JLED2 ASSY
V
JOGR1 ASSY
F
USB1 ASSY
H
USBP1 ASSY
Y
POWER
SUPPLY
ASSY
Q
CDJB ASSY
Q
CDJB ASSY
J
EXTB ASSY
S
PNL2 ASSY
R
PNL1 ASSY
M
MIXB ASSY
HLD2 ASSY
P
LLED ASSY
C
JACK2 ASSY
B
JACK1 ASSY
E
MICT ASSY
• Bottom view
• Bottom view
Note:
The 1 and 2 Assys of JOGT and JLED Assys have the same circuitry, parts, and board shapes.
Only printed information is different, because their part numbers and wiring numbers are different.
They are handled similarly in their production management.
Therefore, either 1 or 2 Assy of the respective Assys is assembled in the respective place.

9
XDJ-RX
56 7 8
56 7 8
A
B
C
D
E
F
NSP 1..EXTA ASSY DWM2548
2..JLED1 ASSY DWX3617
2..JOGT1 ASSY DWX3618
2..USB1 ASSY DWX3620
2..USB2 ASSY DWX3621
2..EXTB ASSY DWX3622
2..JLED2 ASSY DWX3630
2..JOGT2 ASSY DWX3631
2..USBP1 ASSY DWX3636
2..USBP2 ASSY DWX3637
2..LLED ASSY DWX3638
2..HLD1 ASSY DWX3645
2..HLD2 ASSY DWX3646
NSP 1..CDJA ASSY DWM2549
2..CDJB ASSY DWX3614
2..JOGR1 ASSY DWX3619
2..CHF1 ASSY DWX3624
2..HLD3 ASSY DWX3647
NSP 1..MIXA ASSY DWM2550
2..MIXB ASSY DWX3613
2..MICT ASSY DWX3623
2..CRFB ASSY DWX3626
NSP 1..TRMA ASSY DWM2551
2..JACK1 ASSY DWX3615
2..JACK2 ASSY DWX3616
2..PNL1 ASSY DWX3628
2..PNL2 ASSY DWX3629
2..HPJB ASSY DWX3633
2..DPNL1 ASSY DWX3634
2..DPNL2 ASSY DWX3635
1..MAIN ASSY DWX3590
>POWER SUPPLY ASSY DWR1463
Mark No. Description Part No. Mark No. Description Part No.
LIST OF ASSEMBLIES
NOTES:
-
Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.
-
The >mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.

10 XDJ-RX
12 3 4
A
B
C
D
E
F
12 3 4
4. BLOCK DIAGRAM
4.1 OVERALL WIRING DIAGRAM (1/2)
VKN2097-A
CN4002
1
V+5LED
2
V+5LED
3
GNDLED
4
GNDLED
5
J_GRID_SCK
6
J_GRID_RCK
7
J_GRID_xG
8
J_GRID_SI
9
JOGT_SW
10
JOGR_A(JOGR_1)
11
JOGR_B(JOGR_0)
12
PWR_SW/USB_REC
13
N.C/STBY_LED
14
CDJ_PAD1
15
CDJ_CUE
16
CDJ_PAD2
17
CDJ_PLAY
18
CDJ_PAD3
19
CDJ_PAD0
20
GNDD
21
V+3R3D
22
GRID_SI
23
N.C.
24
GRID_SCK
25
N.C.
26
CDJ_LED0
27
CDJ_LED2
28
CDJ_LED1
29
N.C.
30
CDJ_KEY3
31
CDJ_KEY2
32
CDJ_KEY0
33
CDJ_KEY1
34
GNDAD
35
CDJ_AD0
36
CDJ_AD1
37
AD_SEL1
38
AD_SEL0
39
V+3R3AD
VKN1246-A CN4001
15
GNDF
14
GNDF
13
GNDD
12
JOGT_SW
11
JOGR_B
10
JOGR_A
9
V+3R3D
8
V+5LED
7
V+5LED
6
J_GRID_SI
5
J_GRID_xG
4
J_GRID_RCK
3
J_GRID_SCK
2
GNDLED
1
15 14 13 12 11 10
9 8 7
6 5 4 3 2 1
GNDLED
VKN1248-A CN5501
1
V+3R3_AD
2
MIC_LOW
3
MIC_HI
4
GND_AD
5
N.C
6
N.C
7
N.C
8
PWR_SW
9
GNDD
10
CDJ1_GRID5
11
CDJ1_GRID6
12
CDJ1_GRID7
13
CDJ1_KEY0
14
V+3R3D
15
GND_LED
16
CDJ1_LED0
17
V+5_LED
S5503
ASG1102-A
1
25
63
4
RT1
RT2
VKN1419-A
CN9601,9801
GNDF GNDF GNDD
JOGT_SW
JOGR_B JOGR_A V+3R3D V+5LED V+5LED
J_GRID_SI J_GRID_xG
J_GRID_RCK J_GRID_SCK
GNDLED GNDLED
CN9604,9804
AKM1275-A
1
JOGR_B
2
V+3R3D
3
GNDD
4
JOGR_A
CKS6634-A CN9602,9802
1
GNDLED
2
GRID_SCK_5
3
GRID_RCK_5
4
GRID_xG_5
5
GRID_SI_5
6
V+5LED
CKS6634-A
CN9201,9401
1
V+5LED
2
GRID_SI
3
GRID_xG
4
GRID_RCK
5
GRID_SCK
6
GND_LED
CKF1089-A
KN9601,9801
1
CKF1089-A
KN9602,9802
1
PF04PG-Q07
JP9001
1
JOGR_B
2
V+3R3D
3
GNDD
4
JOGR_A
VKN2097-A
CN3401
1
V+3R3AD
2
AD_SEL0
3
AD_SEL1
4
CDJ_AD1
5
CDJ_AD0
6
GND_AD
7
CDJ_KEY1
8
CDJ_KEY0
9
CDJ_KEY2
10
CDJ_KEY3
11
N.C.
12
CDJ_LED1
13
CDJ_LED2
14
CDJ_LED0
15
N.C.
16
GRID_SCK
17
N.C.
18
GRID_SI
19
V+3R3D
20
GNDD
21
CDJ1_PAD0
22
CDJ1_PAD3
23
CDJ1_PLAY
24
CDJ1_PAD2
25
CDJ1_CUE
26
CDJ1_PAD1
27
N.C.
28
PWR_SW
29
JOG1_ENC_B
30
JOG1_ENC_A
31
JOG1_TCH
32
JOG1_LED_SI
33
JOG_LED_xG
34
JOG_LED_RCK
35
JOG1_LED_SCK
36
GND_LED
37
GND_LED
38
V+5_LED
39
V+5_LED
VKN2025-A CN3403
1
GND_LED
2
GND_LED
3
V+5_LED
4
V+5_LED
5
V+12E
6
V+12E
7
V+3R3D
8
V+3R3D
9
V+3R3E
10
V+3R3E
11
GNDD
12
GNDD
13
GNDD
14
EUP_RESET
15
GNDD
16
AUDIO_MUTE
17
GNDD
18
PWR_ON
19
GNDD
20
EUP_REQ
21
GNDD
22
EUP_RDY
23
GNDD
24
EUP_WRITE
25
GNDD
26
EUP_MISO
27
GNDD
28
EUP_MOSI
29
GNDD
CN3801
KM200NA4L
1
V+3R3_AD
2
CRFD_AD
3
GND_AD
4
GND_AD
PF04PG-Q05
JP3202
1
V+3R3_AD
2
CRFD_AD
3
GND_AD
4
GND_AD
CN3601
KM200NA3L
1
V+3R3_AD
2
CHFD_AD
3
GND_AD
PF03PG-Q07
JP3201
1
V+3R3_AD
2
CHFD1_AD
3
GND_AD
CKS5854-A
CN3501
19
GRID_SI
18
GRID_SCK
17
GNDD
16
GNDD
15
GNDD
14
V+3R3D
13
V+3R3D
12
GND_LED
11
GND_LED
10
V+5_LED
9
V+5_LED
8
LED_SCK
7
GNDD
6
LED_RCK
5
GNDD
4
LED_xG
3
GNDD
2
LLED_SI
1
GNDD
VKN1250-A
CN3404
1
GRID_SI
2
GRID_SCK
3
GNDD
4
GNDD
5
GNDD
6
V+3R3D
7
V+3R3D
8
GND_LED
9
GND_LED
10
V+5_LED
11
V+5_LED
12
LED_SCK
13
GNDD
14
LED_RCK
15
GNDD
16
LED_xG
17
GNDD
18
LLED_SI
19
GNDD
VKN1248-A CN4003
1
V+5LED
2
CDJ_LED0
3
GNDLED
4
V+3R3D
5
CDJ_KEY0
6
CDJ_GRID7
7
CDJ_GRID6
8
CDJ_GRID5
9
GNDD
10
PWR_SW/USB_REC
11
N.C./STBY_LED
12
N.C
13
N.C
14
GNDAD
15
MIC_HI/MASTER
16
MIC_LOW/BOOTH
17
V+3R3AD
POWER SW
JOG PLATE
JOG Ploting Plate
CHFB
DWX3624- /J
DDD1683-
FFC/35P,370mm
From/To
MAIN(CN2401)
DDD1684-
FFC/17P,65mm
DDD1690-
FFC/6P,150mm
PF04PG-Q07
CONNECTOR ASS'Y/4P,
70mm
DDD1691-
FFC/15P,105mm
DDD1687-
FFC/39P,270mm
DDD1689-
FFC/19P,40mm
PF03PG-Q07
3P/70mm
PF04PG-Q05
4P/50mm
See "OVERALL WIRIND D
M M M
1/4- 4/4
MIXB ASSY (DWX3613)
NCRFB A
(DWX3
OCHF1 ASSY
(DWX3624)
T
JOGT1 ASSY
(DWX3618)
U
JOGT2 ASSY
(DWX3631)
PLLED ASSY
(DWX3638)
Q Q Q
1/3- 3/3
CDJB ASSY (DWX3614)
R
PNL1 ASSY (DWX3628)
W
JLED1 ASSY
(DWX3617)
X
JLED2 ASSY
(DWX3630)
V
JOGR1 ASSY
(DWX3619)
Note:
The 1 and 2 Assys of JOGT and JLED Assys have the same circuitry, parts, and board shapes.
Only printed information is different, because their part numbers and wiring numbers are different.
They are handled similarly in their production management.
Therefore, either 1 or 2 Assy of the respective Assys is assembled in the respective place.

11
XDJ-RX
56 7 8
56 7 8
A
B
C
D
E
F
VKN2097-A
CN3402
1
V+3R3_AD
2
AD_SEL0
3
AD_SEL1
4
CDJ2_AD1
5
CDJ2_AD0
6
GND_AD
7
CDJ2_KEY1
8
CDJ2_KEY0
9
CDJ2_KEY2
10
CDJ2_KEY3
11
N.C.
12
CDJ2_LED1
13
CDJ2_LED2
14
CDJ2_LED0
15
N.C.
16
GRID_SCK
17
N.C.
18
GRID_SI
19
V+3R3D
20
GNDD
21
CDJ2_PAD0
22
CDJ2_PAD3
23
CDJ2_PLAY
24
CDJ2_PAD2
25
CDJ2_CUE
26
CDJ2_PAD1
27
STBY_LED
28
USB_REC
29
JOG2_ENC_B
30
JOG2_ENC_A
31
JOG2_TCH
32
JOG2_LED_SI
33
JOG_LED_xG
34
JOG_LED_RCK
35
JOG2_LED_SCK
36
GND_LED
37
GND_LED
38
V+5_LED
39
V+5_LED
17
GNDD
18
PWR_ON
19
GNDD
20
EUP_REQ
21
GNDD
22
EUP_RDY
23
GNDD
24
EUP_WRITE
25
GNDD
26
EUP_MISO
27
GNDD
28
EUP_MOSI
29
GNDD
30
EUP_SCLK
31
GNDD
32
EUP_SS2
33
EUP_CONT
34
FAULT_DET
35
QUANTIZE
VKN1248-A CN4003
1
V+5LED
2
CDJ_LED0
3
GNDLED
4
V+3R3D
5
CDJ_KEY0
6
CDJ_GRID7
7
CDJ_GRID6
8
CDJ_GRID5
9
GNDD
10
PWR_SW/USB_REC
11
N.C./STBY_LED
12
N.C
13
N.C
14
GNDAD
15
MIC_HI/MASTER
16
MIC_LOW/BOOTH
17
V+3R3AD
VKN1248-A CN5701
1
V+3R3_AD
2
BOOTH
3
MASTER
4
GND_AD
5
N.C
6
MVR_MUTE
7
STBY_LED
8
USB_REC
9
GNDD
10
CDJ2_GRID5
11
CDJ2_GRID6
12
N.C.
13
CDJ2_KEY0
14
V+3R3D
15
GND_LED
16
CDJ2_LED0
17
V+5_LED
VKN1246-A CN4001
GNDF GNDF GNDD JOGT_SW JOGR_B JOGR_A V+3R3D V+5LED V+5LED J_GRID_SI J_GRID_xG J_GRID_RCK J_GRID_SCK GNDLED GNDLED
CN3801
KM200NA4L
1
V+3R3_AD
2
CRFD_AD
3
GND_AD
4
GND_AD
PF04PG-Q05
JP3202
1
+3R3_AD
2
CRFD_AD
3
GND_AD
4
GND_AD
CN3601
KM200NA3L
1
V+3R3_AD
2
CHFD_AD
3
GND_AD
PF03PG-Q07
JP3203
1
V+3R3_AD
2
CHFD2_AD
3
GND_AD
CKS5854-A
CN3501
19
GRID_SI
18
GRID_SCK
17
GNDD
16
GNDD
15
GNDD
14
V+3R3D
13
V+3R3D
12
GND_LED
11
GND_LED
10
V+5_LED
9
V+5_LED
8
LED_SCK
7
GNDD
6
LED_RCK
5
GNDD
4
LED_xG
3
GNDD
2
LLED_SI
1
GNDD
VKN1419-A
CN9601,9801
GNDF GNDF GNDD
JOGT_SW
JOGR_B JOGR_A V+3R3D V+5LED V+5LED
J_GRID_SI J_GRID_xG
J_GRID_RCK J_GRID_SCK
GNDLED GNDLED
CN9604,9804
AKM1275-A
1
JOGR_B
2
V+3R3D
3
GNDD
4
JOGR_A
CKS6634-A CN9602,9802
1
GNDLED
2
GRID_SCK_5
3
GRID_RCK_5
4
GRID_xG_5
5
GRID_SI_5
6
V+5LED
CKS6634-A
CN9201,9401
1
V+5LED
2
GRID_SI
3
GRID_xG
4
GRID_RCK
5
GRID_SCK
6
GND_LED
CKF1089-A
KN9601,9801
1
CKF1089-A
KN9602,9802
1
PF04PG-Q07
JP9001
1
JOGR_B
2
V+3R3D
3
GNDD
4
JOGR_A
VKN2097-A
CN4002
1
V+5LED
2
V+5LED
3
GNDLED
4
GNDLED
5
J_GRID_SCK
6
J_GRID_RCK
7
J_GRID_xG
8
J_GRID_SI
9
JOGT_SW
10
JOGR_A(JOGR_1)
11
JOGR_B(JOGR_0)
12
PWR_SW/USB_REC
13
N.C/STBY_LED
14
CDJ_PAD1
15
CDJ_CUE
16
CDJ_PAD2
17
CDJ_PLAY
18
CDJ_PAD3
19
CDJ_PAD0
20
GNDD
21
V+3R3D
22
GRID_SI
23
N.C.
24
GRID_SCK
25
N.C.
26
CDJ_LED0
27
CDJ_LED2
28
CDJ_LED1
29
N.C.
30
CDJ_KEY3
31
CDJ_KEY2
32
CDJ_KEY0
33
CDJ_KEY1
34
GNDAD
35
CDJ_AD0
36
CDJ_AD1
37
AD_SEL1
38
AD_SEL0
39
V+3R3AD
CHFB
DWX3624- /J
JLED1,2
DWX3617- /J,
DWX3630- /J
JOG PLATE
JOG Ploting Plate
1683-
35P,370mm
DDD1684-
FFC/17P,65mm
DDD1690-
FFC/6P,150mm
PF04PG-Q07
CONNECTOR ASS'Y/4P,
70mm
DDD1691-
FFC/15P,105mm
DDD1687-
FFC/39P,270mm
m
PF03PG-Q07
3P/70mm
PF04PG-Q05
4P/50mm
VERALL WIRIND DIAGRAM (2/2)".
-When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
-The >mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
-: The power supply is shown with the marked box.
15 14 13 12 11 10
9 8 7
6 5 4 3 2 1
15 14 13 12 11 10
9 8 7
6 5 4 3 2 1
3)
NCRFB ASSY
(DWX3626)
Y
4) OCHF1 ASSY (DWX3624)
PLLED ASSY
(DWX3638)
Q Q Q
1/3- 3/3
CDJB ASSY (DWX3614)
S
PNL2 ASSY (DWX3629)
W
JLED1 ASSY
(DWX3617)
X
JLED2 ASSY
(DWX3630)
T
JOGT1 ASSY
(DWX3618)
U
JOGT2 ASSY
(DWX3631)
V
JOGR1 ASSY
(DWX3619)
hapes.
different.
e.

12 XDJ-RX
12 3 4
A
B
C
D
E
F
12 3 4
4.2 OVERALL WIRING DIAGRAM (2/2)
!
!
!
AKM1277-A CN7201
1
A_MUTE
2
GNDA_HP
3
HP_R
4
GNDA_HP
5
HP_L
6
GNDA_HP
DKP3953-A CN2401
16
GNDD
17
GNDD
18
LVDS0_N0
19
LVDS0_P0
20
GNDD
21
GNDD
22
GNDD
23
LVDS0_N1
24
LVDS0_P1
25
GNDD
26
GNDD
27
GNDD
28
LVDS0_N2
29
LVDS0_P2
30
GNDD
31
GNDD
32
GNDD
33
LVDS0_CLKN
34
LVDS0_CLKP
35
GNDD
36
GNDD
37
GNDD
38
LVDS0_N3
39
LVDS0_P3
40
GNDD
41
GNDD
42
LED_L1
43
LED_L2
44
LED_L3
45
LED_L4
46
GNDD
47
KEY_L1
48
KEY_L2
49
KEY_L3
50
KEY_L4
DKP3953-A CN8401
1
KEY_L4
2
KEY_L3
3
KEY_L2
4
KEY_L1
5
GNDD
6
LED_L4
7
LED_L3
8
LED_L2
9
LED_L1
10
GNDD
11
GNDD
12
LVDS0_P3
13
LVDS0_N3
14
GNDD
15
GNDD
16
GNDD
17
LVDS0_CLKP
18
LVDS0_CLKN
19
GNDD
20
GNDD
21
GNDD
22
LVDS0_P2
23
LVDS0_N2
24
GNDD
25
GNDD
26
GNDD
27
LVDS0_P1
28
LVDS0_N1
29
GNDD
30
GNDD
31
GNDD
32
LVDS0_P0
33
LVDS0_N0
34
GNDD
35
GNDD
CN8801 CKS6646-A
24
UPDN
25
VCC
26
SHLR
27
STBYB
28
RSTB
29
MODE
30
VSD
31
HSD
32
DE
33
DCLK
34
B7
35
B6
36
B5
37
B4
38
B3
39
B2
40
B1
41
B0
42
G7
43
G6
44
G5
45
G4
46
G3
47
G2
48
G1
49
G0
50
R7
51
R6
52
R5
53
R4
54
R3
55
R2
56
R1
57
R0
58
VCC
59
AVDD
60
AGND
VKN1439-A CN2402
1
KEY_QT
2
FAULT_DET
3
EUP_CONT
4
EUP_SS2
5
GNDD
6
EUP_SCLK
7
GNDD
8
EUP_MOSI
9
GNDD
10
EUP_MISO
11
GNDD
12
EUP_WRITE
13
GNDD
14
EUP_RDY
15
GNDD
16
EUP_REQ
17
GNDD
18
PWR_ON
19
GNDD
20
AUDIO_MUTE
21
GNDD
22
EUP_RST
23
GNDD
24
GNDD
25
GNDD
26
V+3R3EUP
27
V+3R3EUP
28
V+3R3D
29
V+3R3D
30
V+12EUP
31
V+12EUP
32
V+5LED
33
V+5LED
34
GND_LED
35
GND_LED
AKM1282-A
CN1802
1
V+12D
2
V+12D
3
GNDUSB_A2
4
GNDUSB_A2
5
USBOCS_A2
6
USBEN_A2
7
GNDUSB_A2S
8
GNDUSB_A2
9
USBDN2_P
10
USBDN2_M
11
GNDUSB_A2
DKN1599-A
CN101
1
GNDSD
2
GNDD
3
xEUPSW
4
V+12SWA
5
V+12SW
6
V+12STB
AKM1292-A
CN8101
1
V+12D
2
V+12D
3
GNDUSB_A1
4
GNDUSB_A1
5
USBOCS_A1
6
USBEN_A1
CN2
B6B-XH-A
1
GNDSD
2
GNDD
3
xEUPSW
4
V+12SW
5
V+12SW
6
V+12STB
PF06PG-S42 JP5901
1
A_MUTE
2
GNDA_HP
3
HP_R
4
GNDA_HP
5
HP_L
6
GNDA_HP
VKN1415-A
CN8402
1
V+5R2D
2
LED_L1
3
LED_L2
4
LED_L3
5
LED_L4
6
GNDD
7
KEY_L1
8
KEY_L2
9
KEY_L3
10
KEY_L4
11
GNDD
VKN1242-A
CN5601
1
V+5_LED
2
LED_RB
3
LED_MIDI
4
LED_USB1
5
LED_USB2
6
GND_LED
7
KEY_USB2
8
KEY_RB
9
KEY_USB1
10
KEY_MIDI
11
GNDD
CN8002 AKM1275-A
1
V+5VBUS_A1
2
V+5VBUS_A1
3
GNDUSB_A1
4
GNDUSB_A1
DKB1118-A
JA8001
VBUS
D- D+
GND
RT1 RT2
CKS4428-A CN8701
1 2
CN8102 AKM1290-A
1
V+5VBUS_A1
2
V+5VBUS_A1
3
GNDUSB_A1
4
GNDUSB_A1
CN8001
AKM1276-A
1
GNDUSB_A1S
2
GNDUSB_A1
3
USBDN1_P
4
USBDN1_M
5
GNDUSB_A1
VKN1427-A
CN2404
1
MIC1
2
GNDA_MIC
3
GNDA_MIC
4
GNDA_MIC
5
GNDA_MIC
6
GNDA_MIC
7
GNDA_MIC
8
GNDA_MIC
9
GNDA_MIC
10
MIC2
11
GNDA_MIC
12
V+15A
13
GNDA_MIC
14
V-15A
15
GNDA_IN1
16
INPUT1_L
17
GNDA_IN1
18
GNDA_IN1
19
GNDA_IN1
20
INPUT1_R
21
GNDD
22
SW_SEL1
23
SW_IN1
VKN1254-A
CN5101
1
MIC1
2
GNDA_MIC
3
GNDA_MIC
4
GNDA_MIC
5
GNDA_MIC
6
GNDA_MIC
7
GNDA_MIC
8
GNDA_MIC
9
GNDA_MIC
10
MIC2
11
GNDA_MIC
12
V+15A
13
GNDA_MIC
14
V-15A
15
GNDA_IN1
16
INPUT1_L
17
GNDA_IN1
18
GNDA_IN1
19
GNDA_IN1
20
INPUT1_R
21
GNDD
22
SW_SEL1
23
SW_IN1
KM200NA6 CN5001
1
MIC1_IN
2
MIC1
3
GNDA_MIC
4
MIC2
5
MIC2_IN
6
GNDA_MIC
KM200NA6 CN5081
1
MIC1_IN
2
MIC1
3
GNDA_MIC
4
MIC2
5
MIC2_IN
6
GNDA_MIC
B2P3-VH
CN1
1.NEUTRAL
3.LIVE
TFT LCD
CWX4352-
DDD1692-
FFC/11P,140mm
JA1601
DKN1237-A
DDD1686-
FFC/50P, 110mm
USB B
From/To
MIXB(CN3403)
USB A
DDD1683-
FFC/35P,370mm
PF-06PG-S42
CONNECTOR ASS'Y,420mm
DDA1050-
SHIELDED CONN-CABLE,285mm
DKP3963-
CRIMP CONNECTOR/6P,105mm
PF04PP-C05
CONNECTOR ASS'Y,50mm
DDD1684-
FFC/23P,65mm
DDA1051-
SHIELDED CONN-CABLE,120mm
NEUTRAL
EARTH
LIVE
POWER CORD
JXJ : DDG1110
UXJCB : DDG1108
LSYXJ8 : ADG1244
XJCN5 : DDG1114
DPK3961-
See "OVERALL WIRIND D
A A A
1/16- 16/16
MAIN ASSY (DWX359
B B B
1/2- 2/2
JACK1 ASSY
(DWX3615)
D
HPJB ASSY
(DWX3633)
E
MICT ASSY
(DWX3623)
K
DPNL1 ASSY
(DWX3634)
F
USB1 ASSY
(DWX3620)
Y
POWER SUPPLY ASSY
(DWR1463)
H
USBP1 ASSY
(DWX3636)
J J J
1/3- 3/3
EXTB ASSY
(DWX3622)

13
XDJ-RX
56 7 8
56 7 8
A
B
C
D
E
F
VKN1435-A
CN2403
1
INPUT2_L
2
GNDA_IN2
3
GNDA_IN2
4
INPUT2_R
5
GNDA_IN2
6
V+15A_IN2
7
V-15A_IN2
8
SW_SEL2
9
SW_IN2
10
A_MUTE
11
GNDD
12
V-15A
13
GNDA_OUTB
14
BOOTH_L
15
GNDA_OUTB
16
GNDA_OUTB
17
GNDA_OUTB
18
BOOTH_R
19
GNDA_OUTB
20
V+15A
21
GNDA_OUTM
22
MASTER2_L
23
GNDA_OUTM
24
MASTER2_R
25
GNDA_OUTM
26
MASTER1_L_HOT
27
GNDA_OUTM
28
MASTER1_L_COLD
29
GNDA_OUTM
30
MASTER1_R_HOT
31
MASTER1_R_COLD
1
KEY_QT
2
KEY_R2
3
KEY_R3
4
GNDD
5
V+5R2D
6
V+5R2D
7
V+3R3D
8
V+3R3D
9
GNDD
10
LCD_PWM
11
GNDD
12
BL_EN
13
BL_ERR
14
GNDD
15
LCD_xRST
16
GNDD
17
GNDD
18
LVDS0_N0
19
LVDS0_P0
20
GNDD
21
GNDD
22
GNDD
23
LVDS0_N1
24
LVDS0_P1
25
GNDD
26
GNDD
27
GNDD
28
LVDS0_N2
23
LVDS0_N2
24
GNDD
25
GNDD
26
GNDD
27
LVDS0_P1
28
LVDS0_N1
29
GNDD
30
GNDD
31
GNDD
32
LVDS0_P0
33
LVDS0_N0
34
GNDD
35
GNDD
36
LCD_xRST
37
GNDD
38
BL_ERR
39
BL_EN
40
GNDD
41
LCD_PWM
42
GNDD
43
V+3R3D
44
V+3R3D
45
V+5R2D
46
V+5R2D
47
GNDD
48
KEY_R3
49
KEY_R2
50
QUANTIZE
VKN1262-A
CN5201
1
INPUT2_L
2
GNDA_IN2
3
GNDA_IN2
4
INPUT2_R
5
GNDA_IN2
6
V+15A_IN2
7
V-15A_IN2
8
SW_SEL2
9
SW_IN2
10
A_MUTE
11
GNDD
12
V-15A
13
GNDA_OUTB
14
BOOTH_L
15
GNDA_OUTB
16
GNDA_OUTB
17
GNDA_OUTB
18
BOOTH_R
19
GNDA_OUTB
20
V+15A
21
GNDA_OUTM
22
MASTER2_L
23
GNDA_OUTM
24
MASTER2_R
25
GNDA_OUTM
26
MASTER1_L_HOT
27
GNDA_OUTM
28
MASTER1_L_COLD
29
GNDA_OUTM
30
MASTER1_R_HOT
31
MASTER1_R_COLD
1
NC
2
GND
3
VGL
4
VCC
5
VGH
6
NC
7
V1
8
V2
9
V3
10
V4
11
V5
12
V6
13
V7
14
V8
15
V9
16
V10
17
NC
18
NC
19
DITH
20
VCOM
21
AVDD
22
AGND
23
GND
24
UPDN
25
VCC
26
SHLR
27
STBYB
28
RSTB
29
MODE
30
VSD
31
HSD
32
DE
33
DCLK
34
B7
35
B6
36
B5
24
GNDD
25
GNDD
26
V+3R3EUP
27
V+3R3EUP
28
V+3R3D
29
V+3R3D
30
V+12EUP
31
V+12EUP
32
V+5LED
33
V+5LED
34
GND_LED
35
GND_LED
AKM1282-A
CN1801
1
V+12D
2
V+12D
3
GNDUSB_A1
4
GNDUSB_A1
5
USBOCS_A1
6
USBEN_A1
7
GNDUSB_A1S
8
GNDUSB_A1
9
USBDN1_P
10
USBDN1_M
11
GNDUSB_A1
AKM1292-A
CN8301
1
V+12D
2
V+12D
3
GNDUSB_A2
4
GNDUSB_A2
5
USBOCS_A2
6
USBEN_A2
CN5801
VKN1236-A
1
GNDD
2
DECK_SELECT
3
TIME_MODE
4
QUANTIZE
5
GNDD
CN8403
VKN1374-A
1
GNDD
2
KEY_R3
3
KEY_R2
4
QUANTIZE
5
GNDD
DKB1118-A
JA8201
VBUS
D- D+
GND
RT1 RT2
CN8202
AKM1275-A
1
V+5VBUS_A2
2
V+5VBUS_A2
3
GNDUSB_A2
4
GNDUSB_A2
JA1401
AKN7115-A
CN8302 AKM1290-A
1
V+5VBUS_A2
2
V+5VBUS_A2
3
GNDUSB_A2
4
GNDUSB_A2
CN8201
AKM1276-A
1
GNDUSB_A2S
2
GNDUSB_A2
3
USBDN1_P
4
USBDN1_M
5
GNDUSB_A2
DDD1693-
FFC/5P,165mm
ETHER
DDD1685-
FFC/31P,155mm
DDA1050-
SHIELDED CONN-CABLE,285mm
USB A
mm
PF04PP-C05
CONNECTOR ASS'Y,50mm
VERALL WIRIND DIAGRAM (1/2)".
A
/16- 16/16
SY (DWX3590)
C C C
1/3- 3/3
JACK2 ASSY
(DWX3616)
L
DPNL2 ASSY
(DWX3635)
G
USB2 ASSY
(DWX3621)
I
USBP2 ASSY
(DWX3637)
J J
1/3- 3/3
ASSY
3622)

14 XDJ-RX
12 3 4
A
B
C
D
E
F
12 3 4
4.3 SIGNAL BLOCK DIAGRAM (CHASSIS SECTION)
CLK, H/V Sync
AC IN RGB(5:6:5)
CN8701 CN8801
IC8801,IC8802,IC8803
Buffer IC
KEY_L1~L4 TC74LCX541FK-K
LED_L1~L4 CN8401 CN5801
V+5R2D KEY_R2,R3
QUANTIZE
CN5601 CN8402
CN1
CN2
CN101
CN8401
CN2401 USBDN2_P/M
USBEN_A2
USBOCS_A2
V+12
Power
PMIC_SDA/SCL
USBUP_DM/DP USBDN1_P/M
PMIC_ON_REQ
Power PMIC_xINT USBHUB_SDA/SCL USBEN_A1
IMX_xPOR USBOCS_A1
PMIC_STBY_REQ USBHUB_xRST V+12
Power
NAND I/F DEVICE
I/O 8bits DN/DP USB HS
USBB VBUS
16bits
32bits
RMII
16bits 10/100BASE-T
400MHz(800MT/s) ENET_REF_CLK
FAULT_DET
SDIO ENET_ETHER_INT
4bits MDC/MDIO
+CLK/CD/WP/CMD ENET_RST
JTAG AUDIO_SPI
DAC_SCLK/DAC_MOSI
/DAC_SS1~3
TXD/RXD AUD_MCLK
I2S AUD4_TXD
L+/L-
DAC_SS1 R+/R-
DAC_RSTN
AUD_MCLK
I2S AUD5_TXD L
DAC_SS3
DAC_RSTN R
IC2202 IC2201
MCLK
AUD_MCLK AUD_MCLK
I2S AUD4_RXD L
IC2203
ADC_RSTN R
AUTH_SDA/SCL
AUTH_xRST
AUD_MCLK
I2S AUD5_RXD L
ADC_RSTN R
AUD_MCLK
I2S AUD3_RXD L (MI
ADC_RSTN R (M
AUD_MCLK
I2S AUD3_TXD L
DAC_SS2
ADC_RSTN DAC_RSTN R
DAC_RSTN
ATT_SEL6DB
ATT_SEL3DB
SW_IN1
SW_IN2
SW_SEL1
SW_SEL2
IMX_AUDIO_MUTE
A_MUTE
CN2402
V+12D/V+12SW
PWR_ON/xEUPSW
V+12EUP V+3R3EUP (POWER)
LVDS0_N0~3 /P0~3
LVDS0_CLKN/P
V+12EUP/V+12STB
V+12A/V+12SWA
KEY_QT
KEY_R2,R3
EUP_REQ FAULT_DET EUP_CONT EUP_RDY EUP_MISO EUP_MOSI EUP_SCLK EUP_SS2 EUP_RST
9.6V
(BL_EN)
18V
-6V
V+5R2D V+3R3D
LED_L1~L4 KEY_L1~L4
PWR_ON
3.3V
BL_DIMMER
BL_ERR
EUP_WRITE AUDIO_MUTE KEY_QT
IC1001
Application Processor
MCIMX6U6AVM08AC -K
7inch TFT LCD
CWX4352-
IC8601
LCD Backlight
Driver
R1290K103A
IC8701
LCD Power
BD81A04EFV-M
IC8401
LVDS Reciever
BU90R104
LVDS I/FGPIO
I2C 2
IC602
PMIC
MMPF0100F0AEP -K
CN1601
for Debug
(SD Card)
SDIO
IC1501
2Gb NAND
NANDF
IC1201
DDR3 1Gb
IC1201
DDR3 1Gb
CN2201
for Debug
(JTAG)
JTAG
IC1701
for Debug
(UART)
UART
USB H1
USB OTG
X2201
CSS1807-
32.768kHz X'tal
X2203
CSS1808-A
24MHz X'tal
IC1401
Ether PHY
LAN8720A
J
E
AK
Ether
GPIO
Logic circuit
SYSTEM
CLOCK
CLK1
CLK2
X2202
DSS1202-A
22.5792MHz
IC1551
AUTH IC
H337S3959
I2C 4
DDR I/F
ECSPI2
ECSPI1
AUD3/4/5
Power Block
DC/DC
Reg.
IC7406
ADC
AK5358AET
IC7001
MASTER DAC
AK4382AVT
IC7701
BOOTH DAC
AK4387ET
IC7405
ADC
AK5358AET
IC7602
ADC
AK5358AET
GPIO
GPIO
IC1801
USB HUB
USB82512AM
IC7201
HP DAC
AK4387ET
X1801
CSS1808-A
24MHz X'tal
AC INLET/3P
DKP3961-
2pin
KEY
LED
I2C 1
A_M
Voltage Detection
Circuit
GPIO
GPIO
GPIO
GPIO
KEY
60pin
DPNL1 ASSY
K
DPNL2 ASSY
L
MAIN ASSY
A
EXTB ASSY
J
POWER
SUPPLY
ASSY
Y
3 6
6
1110 27
13
38
4
12 1
33
32
16
17
12
13
7
2
56
1
3
4
2 7
2 4
3
26
2
1
2
1
2
6
6
5
5
3
39
10
11
12
1
1
1
5
14
15
11
1
11
11
11
10
11
9
9
9
13
13
13
3
6
510
50
39
35
1
44
2-5
18 2 4 6 8 10 22 3 14 16 12 1 20
30,31 26,27
1-4 6-9
7,8 2,3
12,13
30,31
53,54
22,24
3,4
2,6
1,2
5,6
2,32,3
7-10
43,44 45,46 17,18
56,57
48,49
33,34
47-50 42-45
33,28,23,13,
32,27,22,12
49,51,54,59,
50,52,55,60
18,23,28,38,
19,24,29,39
4,25,58
21,59
7-10
2-5
4
4
5
5
3

15
XDJ-RX
56 7 8
56 7 8
A
B
C
D
E
F
CN8001
USBDN1_P/M
V+5VBUS_A1
CN8002
CN8102
USBEN_A1
USBOCS_A1
CN1802
USBDN2_P/M V+12D V+5USB
USBEN_A2 CN8101
USBOCS_A2
V+12D
CN1801
CN8201
USBDN1_P/M USBDN2_P/M
V+5VBUS_A2
USBEN_A1
USBOCS_A1
V+12D CN8202
CN8302
USB HS USBEN_A2
USBOCS_A2
V+12D V+5USB
CN8301
10/100BASE-T
CN2403 CN5201
L+ MASTER2 L MASTER2 L
R+ MASTER2 R MASTER2 R
L+ MASTER1 L COLD MASTER1 L COLD
L- MASTER1 L HOT MASTER1 L HOT
CLK
XD
L+/L-
R+ MASTER1 R COLD MASTER1 R COLD
S1 R+/R-
STN R- MASTER1 R HOT MASTER1 R HOT
A_MUTE
CLK
TXD LL BOOTHLBOOTHL
S3
STN RR BOOTHR
BOOTH R
CLK
RXD L INPUT2_L IN2_L
STN RINPUT2_R IN2_R
SW_SEL2 S5201
SW_IN2 SW_IN2
CLK CN2404 CN5201
RXD LINPUT1_L IN1_L
STN RINPUT1_R IN1_R
SW_SEL1 S5103
SW_IN1 SW_IN1
CLK
RXD L (MIC2 IN) MIC2 MI C2
MIC1
STN R (MIC1 IN) MIC1 MIC1
MIC2
CN5001
CLK
TXD LHPL
S2 CN5081
STN RHPR
CN7201 JP5901
HP L HP L
HP R HP R
EA_MUTE
ATT_SEL6DB ATT_SEL3DB
IC8301
Current Limit IC
TPS2557DRB
JA1601
USB B
DKN1237-
C1401
er PHY
N8720A
JA1401
ETHER
AKM7115-
c circuit
IC7406
ADC
AK5358AET
IC7001
MASTER DAC
AK4382AVT
IC7701
BOOTH DAC
AK4387ET
IC7405
ADC
AK5358AET
IC7602
ADC
AK5358AET
C1801
SB HUB
82512AM
JA8001
USB A
DKN1658-
IC8102
Current Limit IC
TPS2557DRB
IC8101
DC/DC Conv.
BD9328EFJ
IC8201
DC/DC Conv.
BD9328EFJ
IC7201
HP DAC
AK4387ET
IC7004
AMP
NJM4580MD
IC7003
AMP
NJM4580MD
IC7002
AMP
NJM4580MD
IC7401
AMP
NJM4580MD
IC7402
AMP
NJM4580MD
IC7702
AMP
NJM4580MD
IC7202
AMP
NJM4580MD
Q7202, Q7203
Q7204, Q7205
TR AMP
JA5901
HEADPHONE
L/R
IC5001
AMP
NJM4580MD
JA5001 MIC1
JA5002 MIC2
IC5101, IC5102
SW AMP
NJM2121MD
IC5201, IC5202
SW AMP
NJM2121
JA5201
INPUT2
L/R
JA5303
MASTER2
L/R
JA5402
BOOTH
R
JA5401
BOOTH
L
JA5302
MASTER1
R
JA5301
MASTER1
L
JA8201
USB A
DKN1658-
3dB/6dB
A_MUTE A_MUTE
IC7601
AMP
NJM4580MD
A_MUTE
IC5302
AMP
NJM4580MD
IC5301
AMP
NJM4580MD
A_MUTE
A_MUTE
A_MUTE
IC5401
AMP
NJM4580MD
A_MUTE
IC5402
AMP
NJM4580MD
JA5902
HP MINI
L/R
JA5101
INPUT1
L/R
VR5082
MIC2 VR
VR5081
MIC1 VR
LINE/PHONO SW
LINE/PHONO SW
DECK2
DECK1
USBP1 ASSY
H
USBP2 ASSY
I
USB1 ASSY
F
USB2 ASSY
G
JACK2 ASSY
C
JACK1 ASSY
B
MICT ASSY
E
HPJB ASSY
D
6
6
6
16
17
12
13
6
5
5
22
24
28
26
31
30
10
14
18
1
4
8
9
16
20
22
23
10
1
16
20
22
23
10
1
1
1
7
3
5
5
3
7
5
12
1
2
1 3
7
2
6
6
1
5
5
5
3
3
3
7
7
7
7
1
1
1
1
7
1
6
2
5
5
3
3
6
2
5
3
6
9
10
11
12
2
1
1
1
11
1
11
11
11
10
11
9
9
9
13
13
13
3
6
510
3
5
1
3
5
12
2
2
2
2
1 3
7 5
5
5
5
5
5
3
5
3
6
3
6
3
5
4 5
12 4 5
22
24
28
26
31
30
10
14
18
1
1
7
1
7
1
7
1
7
4
8
9
5
4
8
32
23
8
4
5
9,10
9,10
3,4
6,7
2,3
2,3
6,7
3,4
1,2
1,2
1,2
1,2
1,2
1,2
1,2
3,4
1,2

16 XDJ-RX
12 3 4
A
B
C
D
E
F
12 3 4
4.4 SIGNAL BLOCK DIAGRAM (PANEL SECTION)
CN3403
FILTER1
TRIM1
CDJ1_KEY0 TRIM2 MXR_AD0
PWR_SW CDJ1_GRID5~7 HI1
HI2
CDJ1_GRID5~7
CDJ1_LED0 LOW1
HP VOL MXR_AD1
MIC_HI, MIC_LOW HP MIX
MID1
CN5501 AD_SEL0
AD_SEL1
CN4003 CN4002 CN3401
MIC_HI
MIC_LOW CDJ_AD1 CDJ1_AD1
TOUCH/RELEASE CDJ_AD0 CDJ1_AD0
TOUCH/RELEASE TEMPO_ADCT
TEMPO_ADCT/TEMPO AD_SEL0 AD_SEL0
TEMPO AD_SEL1 AD_SEL1
CDJ_KEY0~3 CDJ_KEY0~3 CDJ1_KEY0~3
CDJ_PLAY/CDJ_CUE CDJ1_PLAY/CDJ1_CUE
/CDJ_PAD0~3/PWR_SW /CDJ1_PAD0~3/PWR_SW
PLAY/CUE/PAD1~4
CDJ_GRID0~7 CDJ_GRID0~7 GRID_SCK GRID_SCK
GRID_SI GRID_SI
CDJ_LED0~2
CDJ_LED0~2 CDJ1_LED0~2
JP9001 CN9604/CN9804 EUP_xRST
JOGR_B
JOGR_A
CN9601
/CN9801 CN4001
JOGR_B JOGR_B JOG1_ENC_B
JOGR_A JOGR_A JOG1_ENC_A
From Jog Plate
Jog Touch
JOGT_SW JOGT_SW JOG1_TCH
J_GRID_SI J_GRID_SI JOG1_LED_SI
J_GRID_xG J_GRID_xG JOG_LED_xG
J_GRID_RCK J_GRID_RCK JOG_LED_RCK
J_GRID_SCK J_GRID_SCK JOG1_LED_SCK
CN9602
/CN9802
CN9201
/CN9401
CDJ1_LED0~2
LLED_SI
GRID_xG
GRID_RCK
GRID_SCK
JP3201 JP3202 JP3203 CN3404
CN3601 CN3801 CN3601
CN3501
GRID_xG LLED_SI
GRID_RCK LED_SCK
GRID_SCK LED_RCK
LED_xG
GRID_SI
GRID_SCK
CRFD_AD
CHFD_AD CHFD_AD CHFD2_AD
CRFD_AD
GRID_SCK_5 GRID_RCK_5 GRID_xG_5 GRID_SI_5
SI
SI
GRID_SCK
GRID_RCK
GRID_xG
CHFD1_AD
GRID_xG
GRID_RCK
GRID_SCK
GRID_SI
PWR_SW
CDJ1_KEY0
CDJ1_LED0
CDJ1_GRID5~7
SI
SI
PWR_ON
EUP_REQ
EUP_WRITE
AUDIO MUTE
LED_SI
LED xG
QUANTIZE(KEY_QT)
FAULT_DET
LLED_SI GRID_SCK GRID_SI LED_xG LED_RCK LED_SCK
EUP_RST
GRID_SCK
GRID_SI
EUP_SCLK
EUP_MOSI
EUP_MISO
EUP_CONT
EUP_RDY
EUP_SS2
IC3601
EUP UCOM
R5F364AENFA-U0-K
X3601
16MHz X'tal
DSS1147-
IC3001
TC74VHC164F
Shift Register
TC7
Sh
IC3201
TC74HC4052AF
ANALOG SW
IC4001
TC74HC4052AF
ANALOG SW
KEY
LED
VR
S5503
POWER SW
IC9601/IC9801
PIC10F206-I/OT
TOUCH UCOM
IC9602/IC9802
74VHCT126AFT
3.3V →5V
PC9001
KE-2K18-15
PHOTO
INTERRUPTER
IC9201/IC9401
TC74VHC595F
Shift Register
IC9202/IC9402
TC74VHC595F
Shift Register
IC9203/IC9403
TC74VHC595F
Shift Register
IC9204/IC9404
TC74VHC595F
Shift Register
IC9205/IC9405
TC74VHC595F
Shift Register
JOG
LED
IC4002
TC74VHC164F
Shift Register
VR
/SLIDER
KEY
LED
KN9601
/KN9801
KEY
VR
VR
IC3602
RESETIC
S-80 92 7C NM C -
DECK1
SLIDER SLIDER SLIDER
PNL1 ASSY
R
CRFB ASSY
N
CHF1 ASSY
O
CHF1 ASSY
O
MIXB ASSY
M
CDJB ASSY
Q
JOGR1 ASSY
V
JOGT1 ASSY
T
JOGT2 ASSY
U
JLED1 ASSY
W
JLED2 ASSY
X
2,3
6-8
10-12
15,16
30-33
26-28 12-14
17,15,19,14,
16,18,12
3-6,
10-12
1,2,
15
3-6,
10-13
23,25,21,26,
24,22,28
7-10
1,4
8 13 16
5 2
15
14
12
11 13
3
10
9
1
2
5
4
36 4
10
11
15
14
12
5
2
4
1
3
11 27 38 37 36 35 19 25 20 26
5253
9594
97
31
43
22
22
13
12
34
32
33
52
13
69
66
67
60
61
68 65
9
35 5
5 35
8
8
132
11 29
9 31
8
8 1
22
22
2 2
9
14 1
18 16 14 12 18
2 18 16 14 12 18
2
32
7 33
6 34
5 35
38 2
37 3
40,41,39,
44-46,18
54-57
3,6,21
10
4
11
10
3
2
3
5
6
9
8
12
11
12
6
5
4
3
11
10
12
6
5
4
3
5432
234
14
14
13
12
11
13
12
11
14
13
12
11
9
9
9
9
14
13
12
11
14
13
12
11
5
1
3
6
4
1
18 2 4 6 8 10 22 3 14 16 24 1

17
XDJ-RX
56 7 8
56 7 8
A
B
C
D
E
F
V+3R3E
V+12E
FILTER2
LEVEL/DEPTH CDJ2_KEY0
MXR_AD2 USB_REC CDJ2_GRID5,6
FX CH SEL
CDJ2_GRID5,6
CDJ2_LED0
FX FILTER SEL
MXR_AD3 BOOTH, MASTER STBY_LED
MID2
LOW2
CN5501
CN4003
AD_SEL0
AD_SEL1
CN3402 CN4002
CDJ2_AD1 CDJ_AD1
CDJ2_AD0 CDJ_AD0
AD_SEL0 AD_SEL0
AD_SEL1 AD_SEL1
CDJ2_KEY0~3 CDJ_KEY0~3
CDJ2_PLAY/CDJ2_CUE CDJ_PLAY/CDJ_CUE
/CDJ2_PAD0~3/USB_REC /CDJ_PAD0~3/USB_REC
GRID_SCK GRID_SCK
GRID_SI GRID_SI
CDJ2_LED0~2 CDJ_LED0~2
STBY_LED STBY_LED STBY_LED
BEATS0/1
TAP/FX_ONOFF
MXR_KEY0~2
JOG2_ENC_B JOG2_ENC_B JOGR_B
JOG2_ENC_A JOG2_ENC_A JOGR_A
JOG2_TCH JOG2_TCH JOGT_SW
JOG2_LED_SI JOG2_LED_SI J_GRID_SI
JOG_LED_xG J_GRID_xG
JOG_LED_RCK J_GRID_RCK
JOG2_LED_SCK JOG2_LED_SCK J_GRID_SCK
BEATS0/1
TAP/FX_ONOFF
MXR_KEY0~2
MXR_GRID0~7
MXR_LED8,9
LED0~2 CDJ2_LED0~2
LLED_SI
3404
501
LLED_SI
LED_SCK MXR_LED0~7
LED_RCK
LED_xG
GRID_SI
GRID_SCK MXR_GRID0~7
STBY_LED
(POWER)
USB_REC
CDJ2_KEY0
CDJ2_LED0
BOOTH
MASTER
CDJ2_GRID5,6 CDJ2_GRID5,6
(MVR_MUTE)
CDJ2_KEY0
CDJ2_LED0
USB_REC
EUP_REQ
EUP_WRITE
AUDIO_MUTE
LED_SI
LED_xG
QUANTIZE(KEY_QT)
LED_RCK
LED_SCK
LLED_SI GRID_SCK GRID_SI LED_xG LED_RCK LED_SCK
EUP_RST
EUP_SCLK
EUP_MOSI
EUP_MISO
EUP_CONT
EUP_RDY
IC3601
EUP UCOM
R5F364AENFA-U0-K
IC3002
TC74VHC595F
Shift Register
IC3202
TC74HC4052AF
ANALOG SW
KEY
LED
VR
KEY
LED
VR
VR
KEY
LEVELMETER
LED
KEY
ROTARY ENC
DECK2
IC3001
TC74VHC164F
Shift Register
IC3002
TC74VHC595F
Shift Register
LED
IC3603
NJM2392M
DC/DC Conv.
LLED ASSY
P
CDJB ASSY
Q
JOGR1 ASSY
V
PNL2 ASSY
S
JOGT1 ASSY
T
JOGT2 ASSY
U
JLED1 ASSY
W
JLED2 ASSY
X
Because the circuit of RIGHT DECK is
the same as LEFT DECK, omit it.
Because the circuit of RIGHT DECK is
the same as LEFT DECK, omit it.
Because the circuit of RIGHT DECK is
the same as LEFT DECK, omit it.
Because the circuit of
RIGHT DECK is
the same as LEFT DECK,
omit it.
3-6,
10-12
3-6,
10-12
1-7,
15
1,2,
15
37 36 35 19 25 20 26 10 72 70 71
92
93
1
24
80
77
79
49515052
100
2
9
14 13 12 11
18 16 14 12 18
2 18 16 14
14
11
12
13
1
8
12 18
30-33
26-28
17,15,19,14,
16,18,12
36
35
5
8
11
9
8
7
6
5
38
37
12-14
3,4
5-7
23,25,21,26,
24,22,28
91,78,83-85,
90,2
7-10
86-89
81,82
4,7,23
73-75
4
5
35
32
29
31
32
33
34
35
2
3
7,8
10,11
3
15
8
10
13
5
16
2
7
1
6 8 10 22 3 14 16 24 1
6
5
3
1
5
2
4
14
12
15
11
13
10
9
20
30,31 26,27

18 XDJ-RX
12 3 4
A
B
C
D
E
F
12 3 4
4.5 POWER BLOCK DIAGRAM
V+5_LED
V+5_LED
3.3V
V+3R3D
V+12STB
V+12EUP V+12E
V+12E V+3R3E VCC1,VREF
V+3R3_AD
V+12SW
V+3R3D VCC2
xEUPSW(PWR_ON)xEUPSW(PWR_ON)
V+3R3_AD
V+12SWA
V+3R3_AD V+3R3_AD
V+12A V+12D
V+5LED V+5LED
V+3R3D V+3R3D V+3R3D
V+5LED
V+3R3D V+3R3D
V+3R3DV+3R3D
V+5LED V+5LED V+5LED
V+5LED
V+5LED V+5LED
V+5LED
V+5_LED
V+3R3D V+3R3D V+3R3D
V+3R3_AD
V+3R3_AD
V+3R3_ADV+3R3_ADV+3R3_AD
V+5LED V+5LED
V+3R3D V+3R3D
V+12D V+5R2D
10.75V
V+9R6 AVDD
V-6 VGL
V+18 VGH
VCC
V+3R3D V+3R3D_LVDS
V+5R2D V+5R2D V+5R2D
V+5R2D
V+5R2D
V+5_LED
V+3R3D V+3R3_NF
V+3R3D V+3R3_ENET
V+3R3A_ENET
IC602 IC1001
V+12D V+4R2D
V+3R0VSNVS
V+SNVSCAP
V+1R5VCOREDIG
V+1R375CORE
V+ARMCAP
V+1R375SOC V+SOCCAP
V+3R3PMIC V+3R3D V+2R5VPH
V+2R5VGEN3
VOL
SEP
V+1R8VGEN4 V+PUCAP
V+1R5DDR V+1R5DDR
V+1R5DDR
V+0R75MVREF
MVREF (0.75V)
V+3R15AUX NVCC_ENET
NVCC_LCD
V+3R3D NVCC_EIM/1/2/3
NVCC_GPIO
V+1R5VGEN1 NVCC_SD2/3/NANDF/JTAG
NVCC_CSI
V+1R5VGEN2 NVCC_SD1
V+2R8VHIGH
V+3R3VGEN6
V+5SWBST
V+5R2D
1.5V
MVREF (0.75V)
V+1R5DDR
V+3R3D
V+3R3D
V+3R3A
VIN VSNVS (3.0V) VDD_SNVS_IN VDD_SNVS_CAP
VCOREDIG
SW 1A/1B/1C IN SW1A/B (1.375V)
Max. 2500mA VDDARM_IN VDDARM_CAP
SW1C ( 1.375V)
Max. 1750mA VDDSOC_IN VDDSOC_CAP
SW 2 IN_1,2 SW2 (3.3V)
Max. 2000mA VDDHIGH_IN
VGEN4 (1.8V)
Max . 350mA
VDDHIGH_CAP
VDDIO
VDDPU_CAP
NVCC_PLL_OUT
VIN2
NVCC_LVDS2P5
VGEN3( 2.5V)
Max .100mA NVCC_MIPI
DRAM_VREF
SW4IN SW4 ( 3.15V)
Max.1000mA
SW 3A/B IN SW3A/B (1.5V)
Max .1250mA NVCC_DRAM
VINREFDDR
NVCC_RGMII
VREFDDR
Max .10mA
VIN3 VGEN5 (2.8V)
Max .100mA
VIN1 VGEN 1(1.5V)
Max. 100mA
VGEN2 (1.5V)
Max .250mA
VGEN6 (3.3V)
Max . 200mA
USB_H1_VBUS
DWBSTIN SWBST(5V)
Max .600mA
IC3603 DCDC
NJM2392M
12V→3.3V IC3601
R5F364AENFA
EUP UCOM
Backlight
TFT-LCD
Module
TFT-LCD
Module
CWX4352
IC8601
R1290K103A
5.2V→9.6V
5.2V→-6V
5.2V→18V
DCDC
IC8701
BD81A04EFV
5.2V→10.75V
DCDC
IC105 DCDC
12V→5.2V
BD9328EFJ
PMIC I.MX6
IC1201,1301
DDR3 SDRAM
K4B1G1646G-BCK0
IC1501
NAND FLASH
S34ML02G200TFI00
IC102 DCDC
12V→4.2V
BD9328EFJ
IC1401 Ether
LAN8720A
Microchip
IC9601
Touch UCOM
(PIC10F206-I/P)
Microchip
IC9801
Touch UCOM
(PIC10F206-I/P)
Microchip
IC8401
LVDS
BU90R104
L3603
F1401
IC1551
Authetication IC
H337S3959
L1501
L8802
L8402
F1402
L8801
L8703
P101
L3601
PC9001
Encoder
KE-2K18-15
PC9001
Encoder
KE-2K18-15
LED
IC1801
USB HUB (2ch)
USB82512AM
Voltage down
monitoring circuit 1
Compare with V+3R3EUP
R1551
R1810
L8804
L8805
DECK1
DECK2
LED
LED
LED
L8401
LED
LED
FADER
VOL
VOL
LED
LED
LED
A B C
POWER
SUPPLY
ASSY
Y
MIXB ASSY
M
CDJB ASSY
Q
CDJB ASSY
Q
PNL1 ASSY
R
JLED1 ASSY
W
JOGT1 ASSY
T
JOGR1 ASSY
V
CRFB ASSY
N
V+3R3_AD
FADER
CHF1 ASSY
O
V+3R3_AD
FADER
CHF1 ASSY
O
LLED ASSY
P
JLED2 ASSY
X
JOGT2 ASSY
U
JOGR1 ASSY
V
PNL2 ASSY
S
MAIN ASSY
A
EXTB ASSY
J
DPNL1 ASSY
K
Voltage down
monitoring circuit 2
Compare with V+3R3EUP
Voltage down
monitoring circuit
Voltage over
monitoring circuit
Compare with V+3R3EUP
Compare with V+3R3EUP
Voltage down
monitoring circuit
Compare with V+3R3EUP
0Ω
0Ω
6 2 16
98
2
1
4
23,24
12,37
15,23
1,19
5
17
8
9
20
7
2 4
5
55
5
62
9,23,
37,48
1
7
8
21
59
3
5
5
6
43
44
45
46 1
1
17
14
1
2
13
7
9
5
2
1
1
2
1
2
9
10
13
14
10
11
6
7
20
20
34
34
38
39
19
1
38
39
30
31
5
6
19
1
11
4
17
1
CN5601
CN8401CN2401 CN8402
CN8801
CN8701
CN5701
17
14
1
CN5501
JP9001
2JP9001
2CN9604
6
1
CN9802
6CN9802
CN9401
1
CN9201
CN9804
CN9801CN4001
13
7
9
5
CN9601CN4001
CN4003
1
4
17
CN4003
CN4002
CN4002
CN4002
JP3202 CN3801
1
7 83
4 5 6 3
4 5 6 3
4
28 2932 33
1
JP3203 CN3601
CN3403 (2/2)
CN2402 (2/2)
CN2402
(1/2)
CN3403
(1/2)
CN2
CN101
11
JP3201 CN3601
CN3404
CN3402
CN3401

19
XDJ-RX
56 7 8
56 7 8
A
B
C
D
E
F
V+5A
V+15A
V-15A
V+15A V+15A_M2
V-15A V-15A_M2
V+15AO V+15A_M1
V+15A_M1
V-15AO V-15A_M1
V-15A V-15A_M1
V+5A
XTL3010 V+15A V+15A_BOOTH
V+15A_BOOTH
V+15A
V-15A V-15A_BOOTH
V-15A_BOOTH
V-15A
XTL3010 V+5A
V+3R3A
V+15A
V-15A
V+15A V+15A_IN1
V+15A V+15A_IN1
V-15A V-15A_IN1
V-15A V-15A_IN1
V+5A
V+3R3A
V+15A V+15A_IN2
V+15A_IN2 V+15A_IN
V-15A V-15A_IN2 V-15A_IN2 V-15A_IN
V+5A
V+3R3A
V+15A_MIC
V+15A V+15A_MIC
V-15A_MIC
V-15A V-15A_MIC
V+5A V+5A
V+7R5HP
V+12A
V+12A
XTL3010
V- 7R5HP
XTL3010
V+12D V+5R14_A1 V+5R14A1 V+5VBUSA1 V+5VBUS_A1
V+12D V+5R14_A2 V+5R14A2 V+5VBUSA2 V+5VBUS_A 2
801
ch UCOM
C10F206-I/P)
rochip
IC7702
BOOTH OP AMP
NJM4580MD
IC7405
INPUT1 ADC
AK5358AET
IC7701
Booth DAC
AK4387ET
IC7402
INPUT1 OP AMP
NJM4565MD
IC401 DCDC
12V→±15V
BD9851EFV
1.2MHz
IC7002
MASTER2 OP AMP
NJM4580MD
IC7001
MASTER1, 2 DAC
AK4382AVT
001
oder
2K18-15
IC8101 DCDC
BD9328EFJ
12V→5.0V DCDC
IC8301 DCDC
BD9328EFJ
12V→5.0V DCDC
JA8201
USB A
JA8001
USB A
IC8102
TPS2557DRB
IC8302
TPS2557DRB
IC7406
INPUT2 ADC
AK5358AET
IC7401
INPUT2 OP AMP
NJM4565MD
IC7602
MIC1,2 ADC
AK5358AET
IC7601
MIC1,2 OP AMP
NJM4565MD
IC7202
HP OP AMP
NJM4565MD
IC7201
HP DAC
AK4387ET
IC402 DCDC
12V→±7.5V
BD9851EFV
0.56MHz
IC403 Reg
NJM2886DL3-05
7.5V→5.0V
L408
L407
R7017
L403
L404
R7752
R7445
R7446
R7447
R7448
R7610
R7609
R7248
R7130
R7122
IC5301, 5302
MASTER1 OP AMP
NJM4580D
IC5401, 5402
BOOTH OP AMP
NJM4580MD
IC5101, 5102
INPUT1 OP AMP
NJM2121MD
IC5201, 5202
INPUT1 OP AMP
NJM2121MD
IC5001
MIC1, 2 OP AMP
NJM4580MD
IC7003, 7004
MASTER1,2 OP AMP
NJM4580MD
R7621
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
R7753
R7453
R7455
R7454
R7129
R7127
R7456
R7622
0 Ω
0 Ω
R7754
R5125
R5124
R5225
R5224
R5339
R5337
R5438
R5436
R5027
R5028
ED
A B C
GT2 ASSY
Y
JACK2 ASSY
C
JACK1 ASSY
B
USBP1 ASSY
H
USBP2 ASSY
I
USB1 ASSY
F
USB2 ASSY
G
Voltage down
monitoring circuit
Compare with V+3R3EUP
Voltage down
monitoring circuit
Compare with V+3R3EUP
Voltage down
monitoring circuit
Voltage down
monitoring circuit
Compare with V+3R3EUP
Compare with V+3R3EUP
2,3
2,3
6,7
6,7
8,12
8,12
8
8
8
8
8
12
20
7
6
12
20
7
6
12
14
1
2
1
2
12
14
4
4
4
4
4
15
6
6
6
7
7
7
15
2
4
8
8
8
8
8
4
4
4
4
4
8
8
14
4
4
2 3
3
2
CN2404 CN5101
CN8002
1 2
1 21 2
1 2
CN8101
CN8301
CN1802
CN1801
CN8102
1
2
1
2
CN8202CN8302
CN2403 CN5201

20 XDJ-RX
12 3 4
A
B
C
D
E
F
12 3 4
5. DIAGNOSIS
5.1 STARTUP SEQUENCE
Plugging in of the power cord
The POWER switch (S5503) is set to ON.
Starting supplies of V+12STB/V+12EUP/V+12E
Starting producing V+3R3EUP/V+3R3E at IC3603
Canceling of resetting at EUP UCOM (IC3601)
when the signal at Pin 12 becomes "High"
Initialization of EUP UCOM (IC3601)
The MASTER REC LED flashes in red.
The PWR_ONsignal is set to "Low" to stop
the SWpower output.
Firmware updating starts.
EUP UCOM (IC3601) issues the command to set
the PWR_ONsignal to "High" to start SWpower.
All power ICs start producing power.
The voltage-monitoring circuits start operating.
Start of communication between
EUP UCOM (IC3601) and I.MX6 (IC1001)
Canceling audio muting
Completion of startup
Updating required
Normal startup
Deployment of the program from the flash
ROM (IC1401) and initialization of the built-in
and peripheral modules
Startup indications on the LCD
I.MX6 (IC1001) starts up with its Pin C11
set to "High."
Was a power failure generated?
Judgment of Update mode
Yes
Data of the PWR_SWsignal being "Low" are
input to EUP UCOM (IC3601).