Pioneer DV-989AVi-S User manual

ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2005
DV-989AVi-S
RRV3271
DVD PLAYER
DV-989AVi-S
DV-989AVi-G
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Region No. Remarks
DV-989AVi-S WYXJ AC220–240V 2
DV-989AVi-S YXJRE AC220–240V 5
DV-989AVi-G HLXJ AC220-240V 3
DV-989AVi-S WPWXJ AC220–240V 4
For details, refer to "Important symbols for good services".
T-ZZR OCT. 2005 printed in Japan
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S
2
1234
1234
C
D
F
A
B
E
SAFETY INFORMATION
WARNING !
THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN
CLASS 1 BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING
THE LIMIT FOR CLASS 1.
A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE
APPARATUS.
LASER DIODE CHARACTERISTICS
FOR DVD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 650 nm
FOR CD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 780 nm
LABEL CHECK
(Printed on the Rear Panel)
Additional Laser Caution
∗: See page 87.
1. Loading-status detection switch (S101 on the LOAB assy) are detected
by the microprocessor (IC601 in the DVDM assy).
•To permit the laser diode to oscillate, it is required to set the loading-
status detection switch for the clamp position (the center terminal of
S101 is shorted to +3V).
When the voltage of IC101-pin 21 is +3V, IC601 (microprocessor)
-pin 83 is +3V and IC601-pin 84 is +3V, 650nm laser diode for DVD
oscillates in the DVDM Assy.
When the voltage of IC101-pin 21 is +3V, IC601 (microprocessor)
-pin 83 is 0V (GND) and IC601-pin 84 is +3V, 780nm laser diode for
CD oscillates in the DVDM Assy.
In the test mode * , the laser diode oscillates when microprocessor
detects a PLAY signal, or when the PLAY key is pressed (S104 ON in
the FLKY assy), with the above requirements satisfied.
2. When the cover is open, close viewing through the objective lens with
the naked eye will cause exposure to the laser beam.
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it
-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been traine
d
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, yo
u
should not risk trying to do so and refer the repair to a qualified service technician.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S 3
5 678
5678
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S
4
1234
1234
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6
2.1 PACKING ................................................................................................................................................... 6
2.2 EXTERIOR SECTION................................................................................................................................ 8
2.3 FRONT PANEL SECTION ....................................................................................................................... 10
2.4 LOAD✲✹ MECHA. ASSY.......................................................................................................................... 12
2.5 TRAVERSE MECHA. ASSY-S ................................................................................................................. 14
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM..........................................................................................16
3.1 OVERAL BLOCK DIAGRAM.................................................................................................................... 16
3.2 LOAB ASSY and OVERALL WIRING DIAGRAM..................................................................................... 18
3.3 DVDM ASSY 1/6 [FTS BLOCK] ............................................................................................................... 20
3.4 DVDM ASSY 2/6 [FR BLOCK] ................................................................................................................. 22
3.5 DVDM ASSY 3/6 [EBY/AV1 BLOCK] ....................................................................................................... 24
3.6 DVDM ASSY 4/6 [i.LINK BLOCK] ............................................................................................................ 26
3.7 DVDM ASSY 5/6 [VIDEO BLOCK]........................................................................................................... 28
3.8 DVDM ASSY 6/6 [A-DSP/AQE/SACD BLOCK]........................................................................................30
3.9 AJKB ASSY ............................................................................................................................................. 32
3.10 VJKB ASSY............................................................................................................................................ 34
3.11 FLKY, KEYB and MSWB ASSYS........................................................................................................... 36
3.12 SCRB ASSY (WYXJ5, YXJRE5 Only) ................................................................................................... 38
3.13 POWER SUPPLY UNIT.......................................................................................................................... 40
3.14 WAVEFORMS ........................................................................................................................................ 42
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 45
4.1 LOAB ASSY............................................................................................................................................. 45
4.2 DVDM ASSY ............................................................................................................................................ 46
4.3 AJKB ASSY ............................................................................................................................................. 50
4.4 VJKB ASSY.............................................................................................................................................. 52
4.5 FLKY and KEYB ASSYS ......................................................................................................................... 54
4.6 SCRB ASSY ............................................................................................................................................ 58
4.7 PS ASSY.................................................................................................................................................. 60
4.8 POWER SUPPLY UNIT............................................................................................................................ 61
5. PCB PARTS LIST ........................................................................................................................................... 62
6. ADJUSTMENT ............................................................................................................................................... 86
6.1 ADJUSTMENT ITEMS AND LOCATION ................................................................................................. 86
6.2 JIGS AND MEASURING INSTRUMENTS............................................................................................... 86
6.3 NECESSARY ADJUSTMENT POINTS ................................................................................................... 87
6.4 TEST MODE ............................................................................................................................................ 88
6.5 MECHANISM ADJUSTMENT.................................................................................................................. 89
7. GENERAL INFORMATION ............................................................................................................................. 91
7.1 DIAGNOSIS ............................................................................................................................................. 91
7.1.1 ID NUMBER AND ID DATA SETTING ............................................................................................... 91
7.1.2 SELF-DIAGNOSIS FUNCTION OF PICKUP DEFECTIVE ............................................................... 93
7.1.3 TEST MODE SCREEN DISPLAY ...................................................................................................... 94
7.1.4 SELF-DIAGNOSIS FUNCTION ......................................................................................................... 96
7.1.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE ............................................................. 97
7.1.6 ERROR DISPLAY .............................................................................................................................. 98
7.1.7 TROUBLE SHOOTING .................................................................................................................... 101
7.1.8 FAILURE-TEST METHOD FOR THE HDMI TRANSMITTER IC ..................................................... 103
7.1.9 SERIAL-DOWNLOAD...................................................................................................................... 104
7.1.10 DISASSEMBLY.............................................................................................................................. 105
8. PANEL FACILITIES ...................................................................................................................................... 115
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S 5
5 678
5678
C
D
F
A
B
E
1. SPECIFICATIONS
Specifications
General
System. . . . . . . . . . . . . . . . . . . . . . . . .DVD Player
Power requirements. . . . AC 220-240 V, 50/60 Hz
Power consumption. . . . . . . . . . . . . . . . . . . 25 W
Power consumption (standby) . . . . . . . . . . 0.3 W
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0 kg
Weight. . . . . . . . . . . . . . . . . (HLXJ model) 10.0 kg
Dimensions. . . . 420 (W) x 117 (H) x 340 (D) mm
Operating temperature. . . . . . . . +5°C to +35°C
Operating humidity . . . . . . . . . . . . . . . 5% to 85%
(no condensation)
HDMI output
HDMI output
i.LINK output
i.LINK output . . . . . . . . . . . . . . . . . . . 4 pin (S400)
Component Video output (Y, P B , P R )
Output level . . . . . . . . . . . . . . . .Y: 1.0 Vp-p (75 Ω)
PB, PR: 0.7 Vp-p (75 Ω)
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA jacks
S-Video output
Y (luminance) - Output level . . . . . 1 Vp-p (75 Ω)
C (color) - Output level. . . . . . . 286 mVp-p (75 Ω)
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . S-Video jack
Video output
Output level . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω)
Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA jack
AV connector output
AV Connector (21-pin connector assignment)
AV connector output. . . . . . . . .21-pin connector
This connector provides the video and audio
signals for connection to a compatible color TV
or monitor.
PIN no.
1 . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio 2/R out
3 . . . . . . . . . . . . . . . . . . . . . . . . . . . .Audio 1/L out
4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GND
7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B* out
8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status
11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G* out
15 . . . . . . . . . . . . . . . . . . . . . . . . . . . R* or C* out
17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GND
19 . . . . . . . . . . . . . . . . . . . . . .Video out or Y* out
21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GND
*AV CONNECTOR 1 (RGB)-TV/AV Receiver is
output
Audio output (1 stereo pair)
Output level . . . . . . . . . . . . .During audio output
200 mVrms (1 kHz, –20 dB)
Number of channels. . . . . . . . . . . . . . . . . . . . . .2
Jacks. . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jack
Audio output (multi-channel / L, R, C,
SW, LS, RS)
Output level . . . . . . . . . . . . . During audio output
200 mVrms (1 kHz, –20 dB)
Number of channels. . . . . . . . . . . . . . . . . . . . . .6
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jack
Audio characteristics
Frequency response
. . . . . . . . . . . . . .4 Hz to 44 kHz(DVD fs: 96 kHz)
. . . . . . . 4 Hz to 88 kHz (DVD-Audio fs: 192 kHz)
S/N ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . .118dB
Dynamic range . . . . . . . . . . . . . . . . . . . . 108.8dB
Total harmonic distortion . . . . . . . . . . . 0.0008 %
Wow and flutter . . . . . . . . Limit of measurement
(0.001% W. PEAK) or lower
Digital output
Optical digital output . . . . . . Optical digital jack
Coaxial digital output . . . . . . . . . . . . . . RCA jack
Other terminals
Control in . . . . . . . . . . . . . . . . . . .Minijack (3.5ø)
Control out . . . . . . . . . . . . . . . . . .Minijack (3.5 ø)
Accessories
Stereo audio cable . . . . . . . . . . . . . . . . . . . . . . . .1
Video cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
4-pin S400 i.LINK cable . . . . . . . . . . . . . . . . . . . .1
Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . .1
AA/R6P dry cell batteries . . . . . . . . . . . . . . . . . . 2
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . .1
These operating instructions
The specifications and design of this
product are subject to change without
notice, due to improvement.
. . . . . . . . . . . . . . . . . . . . . . . . 19 pin
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S
6
1234
1234
C
D
F
A
B
E
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
NOTES:
8
7
15
17
3
5
4
12
12
1
6
9
10
11
2
Front side
16
13 14
DV-989AVi-S/YXJRE Only
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S 7
5 678
5678
C
D
F
A
B
E
PACKING parts List
(2) CONTRAST TABLE
DV-989AVi-S/WYXJ, DV-989AVi-S/YXJRE, DV-989-AVi-G/HLXJ and DV-989AVi-S/WPWXJ are constructed the same
except for the following :
Mark No. Description Part No.
> 1 Power Cable See Contrast table (2)
NSP 2 Warranty Card See Contrast table (2)
3 Stereo Audio Cable (L = 1.5 m) VDE1064
4 Video Cable (L = 1.5 m) VDE1065
5 4-pin S400 i.LINK Cable VDE1076
(L = 1.5 m)
NSP 6 Dry Cell Battery See Contrast table (2)
7 Remote Control See Contrast table (2)
8 Battery Cover See Contrast table (2)
9 Operating Instructions See Contrast table (2)
10 Operating Instructions See Contrast table (2)
11 Operating Instructions See Contrast table (2)
12 Polyethylene Bag VHL1051
13 Pad F VHA1394
14 Pad R VHA1395
15 Packing Case See Contrast table (2)
16 Mirror Mat Sheet AHG7010
17 Remote Card See Contrast table (2)
Mark No. Description Part No.
Mark No. Symbol and Description DV-989AVi-S
/WYXJ
DV-989AVi-S
/YXJRE
DV-989AVi-G
/HLXJ
DV-989AVi-S
/WPWXJ
> 1 Power Cable ADG7062 ADG7062 ADG1154 ADG7099
NSP 2 Warranty Card ARY7065 ARY7065 Not used Not used
NSP 6 Dry Cell Battery VEM1021 VEM1021 VEM1031 VEM1031
7 Remote Control VXX2894 VXX2894 VXX2896 VXX2894
8 Battery Cover VNK4936 VNK4936 VNK4422 VNK4936
9 Operating Instructions (English, Spanish) VRD1205 Not used Not used Not used
9 Operating Instructions (English) Not used Not used VRB1402 VRB1402
9 Operating Instructions (Russia) Not used VRC1296 Not used Not used
10 Operating Instructions (French,German) VRD1206 Not used Not used Not used
10 Operating Instructions (Chinese) Not used Not used VRC1290 Not used
11 Operating Instructions (Italian,Dutch) VRD1207 Not used Not used Not used
15 Packing Case VHG2644 VHG2644 VHG2659 VHG2690
17 Remote Card (Russia) Not used Not used ARW7322 Not used
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S
8
1234
1234
C
D
F
A
B
E
2.2 EXTERIOR SECTION
A
CONTACT SIDE
NON-CONTACT
SIDE
A
DE
O
Q
Q
O
MN
J
L
K
J
L
F
I
C
F
G
H
C
E
D
B
B
KM
P
P
GHI
N
Refer to
"2.3 FRONT PANEL SECTION".
47
27
56
56
48
24
23
23 48
48
37
55
4
9
28
56
860
51
51
59 51 59 61
51
59
59
52
59
59
16
59
57
2
59
32
57
33
59
57
31 57
13
11
57
1
59
15
32
58
53
58
55
14
21 18
36
6
5
55
55
35
48
49
30
49
54
48
48
18
34
55 48
17
55
51
39
45
59
43
59
59
38
59
26
19
50
53
53
53
53
19
50
25
22
29
37
57
40
3
12
55
59
56
59
62
48
41
42
10
7
Refer to
"2.4 LOADER MECHA. ASSY".
G
J
I
B
D
H
C
A
46
65 63
64
64
(YXJRE
Only)
(HLXJ
Only)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S 9
5 678
5678
C
D
F
A
B
E
EXTERIOR SECTION parts List
(2) CONTRAST TABLE
DV-989AVi-S/WYXJ, DV-989AVi-S/YXJRE, DV-989-AVi-G/HLXJ and DV-989AVi-S/WPWXJ are constructed the same
except for the following :
Mark No. Description Part No.
1 DVDM Assy VWS1601
2 AJKB Assy See Contrast table (2)
3 VJKB Assy See Contrast table (2)
4 PS Assy VWV2153
5 MSWB Assy VWG2548
> 6 POWER SUPPLY Unit VWR1397
NSP 7 LOADER MECHA. Assy VWT1218
> 8 AC Inlet Assy See Contrast table (2)
9 SCRB Assy See Contrast table (2)
10 Connector Assy(13P) VKP2378
11 Connector Assy PG05KK-E30
12 FFC (31P, AVKB) VDA2102
13 FFC (23P, VJKB) VDA1972
>
14 Power Transformer VTT1169
15 FFC (19P, SCRB) See Contrast table (2)
16 Connector Assy(3P) See Contrast table (2)
>
17 Housing Assy (2P) VKP2379
18 Mini Clamp AEC7373
19 Insulator See Contrast table (2)
20 ••••
21 PCB Support VEC2184
NSP 22 PCB Holder PNW2029
NSP 23 Beam 989 VNE2408
24 Mini Clamp 2 AEC7507
NSP 25 Bottom Plate VNA2836
NSP 26 Bottom Plate 989B VNA2852
27 Bonnet See Contrast table (2)
28 Rear Panel See Contrast table (2)
NSP 29 Chassis 989 See Contrast table (2)
NSP 30 Mechanism Cover VNE2410
NSP 31 PCB Angle VNE2409
32 PCB Holder AJ VNE2330
33 Card Spacer AEC7214
NSP 34 MECHA Angle L VNE2411
NSP 35 MECHA Angle R VNE2412
36 Protection Barrier VEC2485
NSP 37 Spacer AEB7092
38 Tray Panel See Contrast table (2)
39 PLED Assy VWG2557
40 Wire Saddle VEC2310
41 Beam Spacer 989 VEC2499
42 Gasket 3*5*80 VEC2501
43 Power Button Assy See Contrast table (2)
44 ••••
NSP 45 Energy Star Label See Contrast table (2)
NSP 46 ID Label Assy VXW1004
47 Laser Caution Label VRW2257
48 Screw 3x6 B T (FE) ABA1192
49 Screw IBZ30P080FTC
50 Screw BBZ30P100FCC
50 Screw (HLXJ Only)) BSZ40P200FCC
51 Screw PPZ30P080FCC
52 Screw PCZ26P060FCC
53 Screw (3x9 BT) ABA7101
54 Screw VBA1044
55 Screw BBZ30P080FCC
56 Screw BCZ40P060FNI
57 Screw (3x8 BT) ABA7017
58 Screw ABA1200
59 Screw BBT30P100FCC
60 Screw CBZ30P080FCC
61 Screw PCZ30P060FCC
62 Toothed Lock Washers WH40FNI
63 Region Label (YXJRE Only) VRW2259
64 Cushion See Contrast table (2)
NSP 65 SISIR Label (HLXJ Only) VRW2245
Mark No. Description Part No.
Mark No. Symbol and Description DV-989AVi-S
/WYXJ5
DV-989AVi-S
/YXJRE5
DV-989AVi-G
/HLXJ
DV-989AVi-S
/WPWXJ
2 AJKB Assy VWV2149 VWV2149 VWV2148 VWV2148
3 VJKB Assy VWV2152 VWV2152 VWV2150 VWV2151
> 8 AC Inlet Assy VKP2364 VKP2364 VKP2367 VKP2367
9 SCRB Assy VWV1992 VWV1992 Not used Not used
15 FFC (19P, SCRB) VDA1973 VDA1973 Not used Not used
16 Connector Assy(3P) PG03KK-E15 PG03KK-E15 Not used Not used
19 Insulator PNW2766 PNW2766 ANL7028 PNW2766
27 Bonnet VXX3077 VXX3077 VXX3078 VXX3077
28 Rear Panel VNA2837 VNA2837 VNA2841 VNA2873
NSP 29 Chassis 989 VNA2843 VNA2843 VNA2863 VNA2843
38 Tray Panel VNK5850 VNK5850 VNK5849 VNK5850
43 Power Button Assy VXA2724 VXA2724 VXA2725 VXA2724
NSP 45 Energy Star Label Not used Not used Not used AAX8022
64 Cushion PNM1339 PNM1339 AEC7224 PNM1339
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S
10
1234
1234
C
D
F
A
B
E
2.3 FRONT PANEL SECTION
CONTACT SIDE
NON-CONTACT
SIDE
11
11
4
11
3
11
14
4
7
15
9(1/2)
9(2/2)
6
5
10 12
8
11
13
2
11
1
E
F
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S 11
5 678
5678
C
D
F
A
B
E
FRONT PANEL SECTION parts List
(2) CONTRAST TABLE
DV-989AVi-S/WYXJ, DV-989AVi-S/YXJRE, DV-989-AVi-G/HLXJ and DV-989AVi-S/WPWXJ are constructed the same
except for the following :
Mark No. Description Part No.
1 FLKY Assy See Contrast table (2)
2 KEYB Assy VWG2558
3 FFC (17P, FLKB) VDA2089
4 Earth Plate S VNF1131
5 Pioneer Name Plate See Contrast table (2)
6 Aluminum Panel See Contrast table (2)
7 FL Filter VEC2482
8 D Window VEC2492
9 Panel Base Assy See Contrast table (2)
NSP 10 LED Lens VNK5073
11 Screw PPZ30P080FCC
12 Button Sheet L VED1014
13 Button Sheet R VED1015
14 Standby BTN V1 (P) See Contrast table (2)
15 Screw ABA7110
Mark No. Description Part No.
Mark No. Symbol and Description DV-989AVi-S
/WYXJ
DV-989AVi-S
/YXJRE
DV-989AVi-G
/HLXJ
DV-989AVi-S
/WPWXJ
1 FLKY Assy VWG2552 VWG2552 VWG2554 VWG2554
5 Pioneer Name Plate VAM1124 VAM1124 PAN1377 VAM1124
6 Aluminum Panel VAH1430 VAH1430 VAH1434 VAH1430
9 Panel Base Assy VXA2721 VXA2721 VXA2722 VXA2721
14 Standby BTN V1 (P) XAD3191 XAD3191 XAD3186 XAD3191
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S
12
1234
1234
C
D
F
A
B
E
2.4 LOAD✲✹✲✹
✲✹✲✹
MECHA. ASSY
LOADER MECHA. ASSY parts List
A
A
22
1
2
4
3
10
21
11
15
19
14
20
13
12
20
20
20
18
16
17
7
8
9
5
6
6
6
6
Refer to
"2.5 TRAVERSE MECHA. ASSY-S".
Lubricating Oil
GYA1001
Daifree
GEM1036
Cleaning paper
GED-008
Refer to
" Application of Lubricant".
Note :
Lubricating Oil
GYA1001
To DVDM CN101 (Pickup Assy-S)
To DVDM CN104 (Stepping Motor)
To DVDM CN105 (Spindle Motor)
23
K
Mark No. Description Part No.
1 Traverse Mecha. Assy-S VXX2909
2 Loading Motor Assy VXX2912
3 Motor Pulley PNW1634
4 Motor VXM1107
5 Flexible Cable (24P) VDA1947
6 Floating Rubber VEB1351
7 Belt VEB1358
8 Stabilizer VNE2253
9 Loading Base VNL1917
10 Float Base DVD VNL1918
11 Drive Cam VNL1919
12 Gear Pulley VNL1921
13 Loading Gear VNL1922
14 Drive Gear VNL1923
15 SW Lever VNL1925
16 Clamper Plate VNE2342
17 Bridge VNE2343
18 Clamper VNL1924
19 Screw JGZ17P028FMC
20 Screw VBA1094
21 Tray VNL1920
NSP 22 LOAB Assy VWG2426
23 Connector Assy (2P) VKP2253
Mark No. Description Part No.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S 13
5 678
5678
C
D
F
A
B
E
Application of Lubricant
Lubricating Oil
GYA1001
Around the shaft
No. 11
Loading Base
No. 23
Tray
No. 13
Drive Cam
No. 13
Drive Cam
No. 23
Tray
Front View Rear View
Daifree
GEM1036
Inner side of a ditch
Concave of unevenness
Top View Bottom View
Daifree
GEM1036
Daifree
GEM1036
Side of the rib
Lubricating Oil
GYA1001
Concave of unevenness
Daifree
GEM1036 Concave of unevenness
Daifree
GEM1036
Lubricating Oil
GYA1001
Lubricating Oil
GYA1001
Lubricating Oil
GYA1001
Inner side of a ditch
Lubricating Oil
GYA1001
Inner side of a ditch
Lubricating Oil
GYA1001
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S
14
1234
1234
C
D
F
A
B
E
2.5 TRAVERSE MECHA. ASSY-S
To
DVDM CN104
(Stepping Motor)
To DVDM CN105
(Spindle Motor)
To
DVDM CN101
(Pickup Assy)
CONTACT SIDE
NON-CONTACT
SIDE
3
7
8
1
17
16
17
10
13
17
10
6
11
14
16
2
9
15 (Torque : 0.15 ±0.01 N•m)
15 (Torque : 0.15 ±0.01 N•m)
4 (Adjustment screw)
5
(Adjustment
spring)
Screw Tight
GYL1001
Silicone Adhesive
GEM1037
Silicone Adhesive
GEM1037
Cleaning paper
GED-008
Cleaning liquid
GEM1004
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S 15
5 678
5678
C
D
F
A
B
E
TRAVERSE MECHA. ASSY-S parts List
Mark No. Description Part No.
1 Spindle Motor VXM1099
2 Stepping Motor VXM1101
3 Pickup Assy-S OXX8005
4 Skew Screw VBA1080
5 Skew Spring VBH1335
6 Guide Bar VLL1514
7 Sub Guide Bar VLL1515
8 Leaf Spring VNC1023
9 Joint Spring VNC1019
10 Support Spring VNC1020
NSP 11 Mecha.Chassis VNE2248
12 Damper Sheet VEB1335
13 Spacer VNL1913
14 Joint 03 VNL1949
15 Tapping Screw OBA8021
16 Screw BBZ20P050FZK
17 Screw PMA26P100FMC
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S
16
1234
1234
C
D
F
A
B
E
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 OVERAL BLOCK DIAGRAM
DVDM BOARD
DVD
DECODER
(CPPM,CPRM)
EBY-CHIP
PE5286B
()
RF IC
LA9704W
5V
SERVO
DSP
LC78652W
5&3.3V
MPEG2 DECODER
MITSUBISHIAV1
(DVD-A,DTS,TPP)
(Progressive Scan)
M65776BFP
3.3V&1.8V
SYSTEM
CONTROL
CPU
FR30
PD6345A
CLK
Generator
SM8707DV
3.3V (NPC)
16M
SDRAM
16M
PGM
FLASH
MEMORY
3.3V
64M
SDRAM
3.3V
LOADING
MOTOR
DV-989AVi Block Diagram
SPDL
MOTOR
PU
STEPPING
MOTOR
TRAVERSE PICK UP
FTS
DRIVER
M56788AFP
6&12V
SPDL
DRIVER
BA6664FM
6&5V
RF(SACD)
PD5787A
Power Supply
Board
(Murata)
FL
CONTROL
CPU
PE5314C
3.3V Counter
FL Tube
Display
KEY Board
IR(SHARP)
3V,H=12.9mm Board
Audio DSP
XCA56367PV150
3.3V&1.8V
AQE
PD0274A
CPLD IC
LC4032VAA
3.3V (Macnica)
AUDIO
TRANS
(Kitamura)
CD
Direct
SW
LA73054
FLKB
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S 17
5 678
5678
C
D
F
A
B
E
VJKB BOARD
VIDEO OUTx2
S-VIDEO OUTx2
.
COMPONENT OUT
(Progressive/Interlace)
D1/D2 OUT
SCRB BOARD (WY Only)
SCART IN/OUT*2
FRONT Lchx2
FRONT Rchx2
REAR Lch
REAR Rch
SUBWOOFER
CENTER
OPTICAL OUT
COAXIAL OUT
AJKB BOARD
VIDEO
AMP
DRIVER
6ch OUT
LA73054
V
Y
SC
SY
Cb
Cr
192k,24bit,
2chDAC
PCM1738E (BB
SL
SW
SR
C
3-5 Change
I/P Processer
&VIDEO
DAC
(PRO-3)
CM0039AF
(PVC)
1.8V&3.3V
192k,24bit,
2chDAC
PCM1738E (BB
192k,24bit,
2chDAC
PCM1738E (BB
64M
SDRAM
Cb/B
Cr/R
V
SY
SC
Mercury
TSB43CA-
42GGW
3.3V&1.8V
Host
CPU
PD5787A
PD5787A
4M
Flash ROM
SW/C
SW/C(SACD)
SL/SR
SL/ SR
(
SACD
FL/FR(SACD)
Y/G
SR IN
SR 0UT
FL/FR(AV1) SW
SW
SACD
Decoder
CXD2753R
3.3V&2.5V
(SONY)
16M
SDRAM
3.3V
SW/C(AV1)
SL/SR(AV1)
RESOLUTIO
N EXPO
lC
(T-REX)
PD0280B
3.3V&2.5V
HDMI TX
SiI9030
HDMI
connector
SW
i-Link
Connector
FL/FR
VIDEO
AMP
DRIVER
6ch OUT
LA73054
LA73054
B
G
R
FL
FR
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S
18
1234
1234
C
D
F
A
B
E
3.2 LOAB ASSY and OVERALL WIRING DIAGRAM
SCRB ASSY
(VWV1992)
D
PS ASSY
(VWV2153)
I
LOADER ASSY
KEYB ASSY
(VWG2558)
F
MSWB ASSY
(VWG2548)
G
POWER SUPPLY
Unit (VWR1397)
H
PLED ASSY
(VWG2557)
J
WYXJ, YXJRE Only
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S 19
5 678
5678
C
D
F
A
B
E
CN602
1 2
CN601
CN602
+M
S101
LOADING
MOTOR ASSY
: VXX2872
VJKB ASSY
(WYXJ, YXJRE : VWV2152)
(HLXJ : VWV2150)
(WPWXJ : VWV2151)
B
DVDM ASSY
(VWS1601)
A
FLKY ASSY
(WYXJ, YXJRE : VWG2552)
(HLXJ, WPWXJ : VWG2554)
E
AJKB ASSY
(WYXJ, YXJRE
: VWV2149)
(HLXJ, WPWXJ
: VWV2148)
C
WYXJ, YXJRE Only
÷When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or
"PCB PARTS LIST".
÷The >mark found on some component parts indicates the importance of the safety factor
of the part. Therefore, when replacing, be sure to use parts of identical designation.
÷: The power supply is shown with the marked box.
LOAB ASSY
(VWG2426)
K
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

DV-989AVi-S
20
1234
1234
C
D
F
A
B
E
3.3 DVDM ASSY 1/6 [FTS BLOCK]
from / to FR (IC601)
RF_V
RF_A
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
F
F
T
T
F
F
F
T
T
T
1
2
4
A1/6
DVDM ASSY
(VWS1601)
to PU
CN601
to SPINDLE MOTOR
to
CARRIAGE
MOTOR
A1/6
2/6A
K
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com