Pioneer 3LG160 Series User manual

Installation Guide
Single Handle Lavatory Faucet:
3LG160* • 3LG171* • 3LG170B* •
3LG161* • 3LG160B* • 3LG161G* •
3LG170* • 3LG180 • 3PM160* •
3LG180B • 3LG181 • 3LG160H* •
This product meets the following standards:
ASME A112.18.1 •
ANSI A117.1 •
ANSI / NSF 61, SECTION 9 •
CUPC / IAPMO LISTED / ADA COMPLIANT•
CONTAINS NO MORE THAN 0.25% WEIGHTED •
AVERAGE LEAD CONTENT
REV-01 14, 13
Engineering Excellence
Pioneer Industries, Inc. © 2012
Engineering Excellence
Engineering E xc ellence

2REV-01 14, 13
Thank you for purchasing this Pioneer quality product.
Tools Required
Adjustable
Wrench
Teon Tape Rags 3/32” Allen
Wrench
Prior to Installation
Observe all local plumbing and building codes before you begin •
installation.
Carefully shut off both hot and cold water supplies from under the sink. •
Plug the sink drain with a soft cloth to prevent intrusion of debris or the •
loss of any faucet parts.
For replacement installations, carefully remove the existing•
faucet and clean the entire surface of the sink mounting holes.
Pioneer reserves the right to make changes in the design of faucets without •
notice as specied in the pricebook.

3REV-01 14, 13
Faucet Installation
Slide the base plate (A) to the underside of the faucet.•
Apply adequate plumbers putty or sealant along the boundary of •
the base plate (A) if necessary.
Clean the mounting surface If necessary.•
Insert the faucet through sink hole.•
Thread the mounting bolt (B) into the faucet from beneath.•
Slide the mounting plate (C) through the mounting bolt.•
Thread the mounting nut (D) from underside. Secure the faucet to the •
sink with mounting nut (D) supplied with the faucet.
Remove the excess plumbers putty or sealant from the faucet.•

4REV-01 14, 13
Pop-up Drain Installation
Remove the pop-up stopper (E) and pop-up ange (F) from the pop-up 1.
assembly.
Apply adequate amount of plumbers putty underside of pop-up ange 2.
(F). Then insert pop-up drain assembly from underside of the sink and
secure the pop-up ange (F) from the top.
Rotate the drain body so that horizontal rod hole faces back of the fau-3.
cet.Hold the pop-up assembly in place and tighten the locknut (G).
Remove the excess putty. Connect the trap (H) (check manufacturer’s 4.
instructions for installation).
Remove rod nut (I).5.
Ensure the washers (K) is in place (for brass pop-up only). Insert rod (J). 6.
Tighten the rod nut (I).
Push rod down to open drain. Insert the pop-up stopper (E) carefully. 7.
Test if the pop-up stopper (E) is working properly.
Connect pop-up bracket to the rod using clip (L). Tighten the thumb-8.
screw (M) to connect pop-up bracket to pop-up lift rod.

5REV-01 14, 13
Pop-up Drain Installation

6REV-01 14, 13
Grid Drain Installation
Remove the grid trim ring (N) from the grid drain assembly (O).1.
Apply adequate amount of plumbers putty underside of the grid trim ring 2.
(N). Attache the grid trim ring (N) from top of the drain hole. Insert the
grid drain assembly (O) from under the lavatory sink.
Hold the grid trim ring (N) in place while threading the locknut (P) until 3.
the locknut is snug with the underneath the lavatory sink.
Tighten the locknut (P).4.
Remove the excess putty. Connect the trap (H) (check manufacturer’s 5.
instructions for installation).

7REV-01 14, 13
Main Supply Connection
Connect the faucet inlet tubes (Q) to inlet supply lines (R). Connect the •
supply stops (S) to the inlet supply lines (R) (left is hot water supply and
right is cold water supply). Make sure inlet supply lines (R) are securely
tighten. Do not over- tighten.
Turn on water. Check for any leaks. Make sure all the connections are •
secure.
Remove aerator (T).•
Open the handle.•
Flush and allow water to run at full ow for at least one minute.•
Replace aerator (T).•

8REV-01 14, 13
To Set or Adjust Temperature Limit Stop
Caution: Ceramic cartridge is preset at the factory at maximum tempera-
ture. Adjust as necessary. Please see the instructions below:
Turn off water and relieve the pressure.•
Remove handle (U) by removing Button (W) and loosening set •
screw (V) and lift off the handle (U). Note: For 3LG180, 3LG180B
and 3LG181- Remove handle (U) by remove button (W) (located on
the top of the handle) and loosening Phillips screw.
Unscrew retainer sleeve (X) and retaining nut (Y).•
Use two ngers to raise the red adjustment ring (Z).•
Turn adjustment ring (Z) counterclockwise to decrease the tempera-•
ture setting and clockwise to increase the temperature. Replace the
adjustment ring (Z).
Reassemble and test until desired safe temperature is reached. •
(Note: Ensure proper alignment of cartridge with notch in valve
body.)
For more care information or trouble shooting inquiries about your
Pioneer Product, please see the contact information on the back page.

9REV-01 14, 13
3325 S. Gareld Ave. | Commerce, CA 90040
Telephone: [phone] | [phone] | Fax: [phone]
Hours: M - F, 7:30am to 5:00pm PST
www.pioneerind.com
Engineering Excellence
Eng ineering E xcellence