Piscine Italia ARIA 200 User manual

User's manual
EN
Sauna Room
1/10
ARIA 200 / BEA 200
2020/08/25

EN
2/10
PREFACE
Thank you very much for purchasing our product.
Please read this manual carefully before assembling and save it afterwards. Please write down the control
box serial number of the cabin as this number will be required in case of repair or order of spare parts.
ATTENTION
Installation and repair should only be done by a qualified electrician!
Check power supply rating and make sure the grounded outlet is correctly connected before installation.
Use original parts only. Do not share the outlet with any other appliances.
When not in use, turn off the cabin's power unit.
Locate your cabin indoors and on a flat, level and dry surface.
DANGER
Heaters shall not be subjected to water spray; shower heads shall not be installed within the infrared cabin.
Covering the radiator causes a fire hazard due to overheating. Do not cover the heaters !
Keep flammable or easily combustible materials/objects (eg.towels) away from the radiator at all times.
Do not touch the radiator during and shortly after use as a burning hazard exists due to hot parts.
The light bulb heats in use. If the bulb needs to be changed, unplug the cabin and let the bulb cool down
before changing it.
Should the electrical connection get damaged, it must be replaced-either by the manufacturer or by a
licensed electrician!
WARNING
If you suffer from illness or other health-related problems, especially heart conditions or circulatory
disturbances or if you take medication, you should consult a doctor before using the infrared cabin.
Children and frail persons should never be in the cabin without supervision.
If you feel uncomfortable while using the infrared cabin, stop immediately and consult with your doctor.
Never go to a hot infrared cabin if you have taken alcohol, strong medicines or narcotics.
Technical data
Model
Cabin material
Length
Width(depth)
Height
Voltage
BEA 200
Regular hemlock
2000 mm
1500 mm
2005 mm
380volt 50Hz
Sauna stove Total output 6000W

3/10
Cabin Individual parts (variations possible)
NO NAME Q'TY
1
3
4
6
8
10
1
1
1
1
1
1
11 1
12
1
13
2 1
5 1
91
1
14
71
2
EN
Back panel 1(1163*1964*48mm)
Back panel 2(867*1964*48mm)
Right side panel(2000*1500*48mm)
Left side panel(2000*1500*48mm)
Door cross beam(upper,1880*90*40mm)
Door cross beam(down,1880*70*40mm)
Bench support panel 1(1902*90*40mm)
PARTS LIST
1
25
21
22
24
23
2
18
17
4
3
5
26
6
19
9
11
16
12
13
14
7
10
15
8
20
7
Bench support panel 2 (1900*90*20mm)
Back decorative bar (1898*90*20mm)
Side glass 1 (1858*668*8mm)
Side glass 2 (1858*668*8mm)
Top panel (1961*1457*40.5mm)
Bench surface panel 1(1902*500*33mm)
Back guardrail (1900*300*46mm)

NO NAME Q'TY
15
17
6
1
1
16 1
4/10
EN
18
19
20
21
22
23
24
25
26
1
4
2
2
4
2
1
1
Oven guardrail 1 (420*367*33mm)
Oven guardrail 2 (280*367*33mm)
Oven guardrail 3 (520*33*33mm)
Oven guardrail 4 (356*90*20mm)
ASSEMBLE INSTRUCTIONS
Assemble tips
Tools
Spiral drill (kit)
Screwdriver (kit)
Allen Wrench (kit)
Spirit level
Tape measure Electric drill
Cutter
Pencil
Hammer
Stepladder
Hardware parts (variations possible)
Please remove transport packaging and inspect that your infrared cabin has been delivered complete and
intact before beginning assemble.
A least 2 persons are required for assemble of the cabin
Please check the countersink and hole diameter of the drill holes to avoid damaging the wood..
The minimum room height required for installation is 2170mm
32x 66x
Φ4*35
Φ4*50
2x
Φ6*60 Rubber
4m
Strip Glass clip
1x 4x
Mixed Screw
Bench support panel 3 (358*90*20mm)
Bench surface panel 2(1900*400*33mm)
Floor panel 1 (1900*704*28mm)
Floor panel 2 (1900*704*28mm)
Glass door (1824*557*8mm)
Door handle (outside,300 mm & inside,300 40mm) *40*40 *40*
MDF cover 1 (1220*1961*3mm)
MDF cover 2 (237*1961*3mm)

ASSEMBLE INSTRUCTIONS
Assemble steps
(3)(4)
EN
(1) (2)
5/10
1
2
4-Φ4*35
2
5
4
17
18
6
1
3
3
10-Φ4*50
12-Φ4*35

6/10
EN
ASSEMBLE INSTRUCTIONS
Assemble steps
(7)(8)
(5) (6)
X2
7
9
8
11
15 X6
14 X2 12
13
10 12-Φ4*50
4-Φ4*50
6-Φ4*50
200MM
24-Φ4*35

7/10
EN
ASSEMBLE INSTRUCTIONS
Assemble steps
(11)
(9) (10)
Power line
16
21 X2
24 X2
23 X4
22 X2
25
26
Rubber
Strip
Glass clip
20
2- Φ 6*60
Wood cover
19
Note: connect all cables on the roof of the cabin
24-Φ4*35

CIRCUIT DIAGRAM
8/10
EN
USB
R
FM/MP3/BLUETOOTHPLAYER
USB
R
FM/MP3/BLUETOOTHPLAYER
OUT:DC5V/2A
Speaker 8Ω2W Speaker 8Ω2W
Antenna
OUT:DC12V/3A
Color light
DC12V/8W
Mp3 player
Long press " " to activate the MP3 player.
USB or Bluetooth mode:
USB---Bluetooth---FM radio
You can select songs by short pressing the / keys and adjust the volume (0-32) by long pressing
The / keys. The key for pause.
FM radio mode:
Long press to search stations (87.5MHZ-108MHZ) automatically, the system will save all of them;
You can select stations by short pressing the / keys and adjust the volume (0-32) by long
Pressing the / keys.
You can select the mode by short pressing the " "button:
MM
MM
The key for mute sound.
.
OPERATING INSTRUCTIONS
USB
R
FM/MP3/BLUETOOTHPLAYER
USB
FM/MP3/BLUETOOTHPLAYER

SERVICE
Use instructions
Drink plenty of liquids before and after use of the infrared cabin.
Dry yourself off completely.
The optimal cabin temperature for a pleasant session lies between 35 and 60℃.
After a heating period of an hour at the latest, the cabin should be switched off and a heating brake of
at least 30 minutes should be taken.
Maintenance instructions
Clean the cabin with a damp cotton towel, dry with a clean dry towel.
Clean the glass with a window/glass cleaner and a soft cloth.
Do not pour water in the control panel or clean it with wet cloth. For cleaning purposes, use a cleaning
cloth that has been only slightly moistened with a mild soapy solvent (dish detergent).
Do not use chemical detergents to clean the cabin.
Please fasten the screws of the bench once every three months, avoid the loose or drop off.
9/10
It is recommended to take a warm shower and relax after use.
Notes:
EN

SERVICE
Fill in this form and make a picture of it and Email to:
Date of purchase:
Serial Number:
Reference number:
Name:
Article state (unopened, just opened or used):
Please encircle on picture below which heater or which panel
has a fault.
Attach pictures of the problem and send them through email.
GUARANTEE CARD
10/10
EN
Control unit label sample
1
25
21
22
24
23
2
18
17
4
3
5
26
6
19
9
11
16
12
13
14
7
10
15
8
20
7