Pit Boss MEMPHIS PBMEMU1 User manual
.
, .
.
ITM#0354675
MODEL: PBMEMU1
PART: 10956
41
IMPORTANT, READ CAREFULLY, RETAIN
FOR FUTURE REFERENCE. MANUAL MUST
BE READ BEFORE OPERATING!
For outdoor and household use only. Not for commercial use.
Fuel and accessories not included.
MEMPHIS ULTIMATEMEMPHIS ULTIMATE
AUSTRALIA AND NEW ZEALAND
GAS SAFETY CERTIFICATION
®
DO NOT REMOVE
. 10815
3
Parts & Specs......................................................................4
Assembly Preparation......................................................6
Assembly Instructions
Mounting The Left Front Support Leg ....................................6
Mounting The Right Front Support Leg..................................6
Mounting The Back Support Legs............................................ 7
Mounting The Casters................................................................. 7
Attaching The LP Gas Cylinder Wire Retainer........................ 7
Mounting The Knob To The Air Damper .................................8
Attaching The Smoker Cabinet Assembly...............................8
Inserting The Wood Chips Box ..................................................8
Installing The Lower Cabinet Drawers ....................................8
Placing The Water Pan ................................................................9
Inserting The Cooking Grids Into The Smoker Cabinet........9
Mounting The Smoker Door Handle........................................9
Mounting The Thermometer Into The Smoker Door ......... 10
Mounting The Smoker Door Hinges ...................................... 10
Installing The Smoker Door ..................................................... 10
Mounting The Grill Onto The Cart........................................... 11
Connecting The Electrical Components
For The Smoke Cabinet.........................................................11
Attaching The Electrical Back Cover........................................12
Assembling The Smoker Air Dampers.....................................12
Installing The Charcoal Ash Tray..............................................12
Installing The Grease Tray Components ................................13
Mounting The Grease Shields Into The Main Chamber......13
Installing The Tool Hooks ........................................................ 14
Mounting The Side Tables........................................................ 14
Installing The Cooking Grid Supports.................................... 14
Installing The Heat Tents...........................................................15
Installing The Charcoal Tray Lifting System..........................15
Placing The Control Knobs ....................................................... 16
Attaching The Charcoal Tray Air Damper Handle................ 16
Placing The Charcoal Tray......................................................... 16
Mounting The Smoke Stack......................................................17
Installing The Warming Racks..................................................17
Placing The Cooking Grids.........................................................17
Inserting The Thermometers................................................... 18
Mounting The Lid Handles....................................................... 18
Mounting The Wire Hose Retainer......................................... 18
Installing The Battery................................................................ 19
COPYRIGHT NOTICE
Copyright 2022. All right reserved. No part of this manual
may be copied, transmitted, transcribed, stored in a retrieval
system, in any form or by any means without expressed
written permission of,
Dansons
3411 North 5th Avenue, Suite 500, Phoenix, , 85013
www.pitboss-grills.com
Genesis International Corporation Pty Ltd.
1/71 Truganina Road Malaga WA 6090
+61 8 9248 9822
service@genesiscorp.com.au
4
PB – ELECTRIC REQUIREMENTS
220-240 V, 50 Hz, 1650 W, GROUNDED PLUG
Part Description Qty
1 Thermometer 2
2 Thermometer Bezels 2
3 Smoke Stack Lid 1
4 Smoke Stack 1
5 Warming Racks 2
6 Lid Handles 2
7 Lid Handle Standoff's 6
8 Left Side Table 1
9 Tool Hooks 6
10 Right Side Table 1
11 Charcoal Tray 1
12 Charcoal Tray Lifting System 1
13 Grill Chambers Assembly 1
14 Heat Tents 3
15 Heat Tents Supports 3
16 Gas Control Knobs (Black) 3
17 Smoker Control Knobs (Silver) 1
18 Smoker Air Damper Pull Handle Assembly 2
19 Charcoal Tray Air Damper Handle Assembly 1
20 Charcoal Tray Lift Handle Assembly 1
21 Cooking Grid Back Supports 2
22 Cooking Grid Front Supports 2
23 Grease Shields 4
24 Charcoal Ash Tray Guides 2
25 Charcoal Ash Tray 1
26 Gas Drip Tray Guides 2
27 Gas Grease Tray 1
28 Grease Cups 2
29 Knobs 3
30 Cooking Grids 4
31.1 Smoker Top Air Dampers - Left 1
31.2 Smoker Top Air Dampers - Right 1
32 Smoker Cabinet Assembly 1
33 Smoker Cooking Grid (Large) 1
Part Description Qty
34 Smoker Cooking Grid (Medium) 1
35 Smoker Cooking Grid (Small) 1
36 Water Pan 1
37 Water Pan Support 1
38 Smoker Door Handle 1
39 Smoker Thermometer 1
40 Smoker Door 1
41 Electric Wire Back Cover 1
42 LP Gas Cylinder Wire Retainer 1
43 Left Rear Support Leg 1
44 Right Rear Support Leg 1
45 Left Front Support Leg 1
46 Right Front Support Leg 1
47 Lower Cabinet Assembly 1
48 Drawers 2
49 Drawer Handle Standoff's 4
50 Drawer Handles 2
51 Smoker Door Hinges 2
52 Wood Chips Box Assembly 1
53 Locking Caster Wheels 4
54 Caster Support Plates 2
A M6x15 mm Screws (Black Zn) 28
B M5x10 mm Screws (Black Zn) 3
C M6x60 mm Screws (Black Zn) 8
D M6x10 mm Screws (Black Zn) 35
E M6x35 mm Screws (Black Zn) 6
F M4x10 mm Screws (Black Zn) 24
G M4x8 mm (White Zn) 16
H M5x10 mm Shoulder Bolts (White Zn) 8
I AA Battery 1
J M6 Nuts 8
K Hinges Pins 2
L R Clips 3
M M6x30 mm Screws (Black Zn) 4
NOTE: Due to ongoing product development, parts are subject to change without notice. Contact
Customer Service if parts are missing when assembling the unit.
5
MODEL ASSEMBLED (WxDxH) WEIGHT INPUT
1 1,880 667 1,230 /
74.0 26.2 48.4 .
98 /
216 31.5 MJ/H
COOKING AREA
1,040 / 161.2
2,495 / 386.8
3,535 / 548.0
1,040 / 161.2
2,495 / 386.8
3,535 / 548.0
1,804 / 279.6
1,672 / 259.2
1,540 / 238.8
5,016 / 777.6
12,083 / 1,873
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18 19
20
21
22 23
24
25
26
27
28
29
30
31.1 31.2
32
33
34
35
36
37
38
39
40
41
42
43
46
47
48
49
50
52
53
45
44
51
54
6
Parts are located throughout the shipping carton, including underneath the grill. Inspect the grill, parts, and hardware blister
pack after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the grill
before assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt
to assemble. Shipping damage is not covered under warranty. Contact Bunnings Australia or Genesis International Corporation
Pty Ltd. for Customer Service.
service@genesiscorp.com.au | +61 8 9248 9822
IMPORTANT: To ease installation and avoid injury, two people are required when assembling this unit.
Tools required for assembly: screwdriver and wrench.
A wrench for the wheels is included.
IMPORTANT: It is advised to read each step entirely before starting assembly on instructions. Do not tighten screws
completely until all screws for that step have been installed.
1.
Parts Required:
1 x Left Front Support Leg (#45)
1 x Lower Cabinet Assembly (#47)
2 x M6x60 mm Screw (#C)
1 x M4x10 mm Screw (#F)
Installation :
• Place a piece of cardboard on the floor to prevent
scratching the unit.
• Mount the Left Front Support Leg to the Lower
Cabinet Assembly using three screws, as shown.
2.
Parts Required:
1 x Right Front Support Leg (#46)
2 x M6x60 mm Screw (#C)
1 x M4x10 mm Screw (#F)
Installation :
• Mount the Right Front Support Leg to the Lower
Cabinet Assembly using three screws, as shown.
1
45
2
46
7
3.
Parts Required:
1 x Left Rear Support Leg (#43)
1 x Right Rear Support Leg (#44)
2 x Caster Support Plates (#54)
4 x M6x60 mm Screw (#C)
Installation :
• Mount the Left Rear Support Leg and the Right Rear
Support Leg to the Lower Cabinet Assembly using
two screws in each leg, as shown in illustration 3A.
• Remove the pre-assembled screws from the Rear
Support Legs. Secure the Caster Support Plates to
the Rear Support Legs using the previously removed
screws, as shown in illustration 3B.
4.
Parts Required :
4 x Locking Caster Wheels (#53)
Installation :
• Turn the Lower Cabinet Assembly upside down and
mount the four Locking Casters to the Lower Cabinet
Assembly. Tighten the Locking Casters into place
using the wheel wrench (included).
• Carefully, turn the Cart into to an upright position.
5.
Parts Required :
1 x LP Gas Cylinder Wire Retainer (#42)
1 x R-Clip (#L)
Installation :
• Insert the LP Gas Cylinder Wire Retainer between the
Support Legs on the left side of the unit. Insert the
hooked end first, then secure the other end using the
R-Clip. Note illustration.
453
53
53
53
5
42
3
3
43
54
44
54
8
6.
Parts Required :
1 x Knob (#29)
1 x Smoker Cabinet Assembly (#32)
1 x M5x10 mm Screw (#B)
Installation :
• Mount the Knob to the Air Damper on the back side
of the Smoker Cabinet. Secure with screw from the
inside.
7.
Parts Required :
2 x M6x15 mm Screw (#A)
2 x M6x35 mm Screw (#E)
Installation :
• Attach Smoker Cabinet Assembly to the Lower Cabinet
Assembly. Note illustration for proper location of
different screws.
8.
Parts Required :
1 x Wood Chip Box Assembly (#52)
Installation :
• Slide Wood Chip Box Assembly onto the Wood Chip
Box support rails of Lower Cabinet Assembly.
: When removing the Wood Chip Box from the
smoker, lift up on the handle and then pull out the
Wood Chip Box.
9.
Parts Required :
2 x Drawers (#48)
4 x Drawer Handle Standoffs (#49)
2 x Drawer Handles (#50)
4 x M6x10 mm Screw (#D)
Installation :
• First, assemble a Drawer Handle by aligning and
inserting the Drawer Handle Standoffs onto each
end of the Drawer Handles. Repeat the same step for
other Drawer Handle. Once assembled, mount each
Drawer Handle onto a Drawer. Note illustration 9A.
• Insert each Drawer into the Lower Cabinet Assembly,
as shown in illustration 9B.
6
29
32
7
8
9
9
52
49
48
49 50
9
10.
Parts Required :
1 x Water Pan (#36)
1 x Water Pan Support (#37)
Installation :
• Slide the Water Pan Support into the lowest rails of
the Smoker Cabinet Assembly. Note illustration 10A.
• Place the Water Pan onto the Water Pan Support.
Note illustration 10B.
11.
Parts Required :
1 x Smoker Cooking Grid (Large) (#33)
1 x Smoker Cooking Grid (Medium) (#34)
1 x Smoker Cooking Grid (Small) (#35)
Installation :
• Slide each of the Smoker Cooking Grids into the rails
of the Smoker Cabinet Assembly. Note illustration for
proper arrangement.
12.
Parts Required :
2 x Large Handle Standoffs (#7)
1 x Smoker Door Handle (#38)
1 x Smoker Door (#40)
4 x M6x35 mm Screw (#E)
Installation :
• First, assemble the Smoker Door Handle by aligning
and inserting the Large Handle Standoffs onto each
end of the Smoker Door Handle. Once assembled,
mount the Smoker Door Handle onto the Smoker
Door, as shown.
10
10
11
12
37
36
33
34
35
40
7
738
10
13.
Parts Required :
1 x Smoker Thermometer (#39)
Installation :
• First, remove the washer and wing nut from the
Smoker Thermometer.
• Insert the Smoker Thermometer stem through the
mounting hole in the front of the Smoker Door
Assembly. From the inside door, place the fiber
washer and wing nut onto the mounting thread pole
and tighten by hand. Do not over tighten.
14.
Parts Required :
2 x Smoker Door Hinges (#51)
8 x M4x8 mm White Zn Screw (#G)
Installation :
• Mount the two Smoker Door Hinges to the Smoker
Door using four screws in each hinge.
IMPORTANT: Take note of proper orientation of the
Smoker Door Hinge during installation.
15.
Parts Required :
8 x M4x8 mm White Zn Screw (#G)
Installation :
• Mount the Smoker Door to Lower Cabinet Assembly.
as shown in illustration. Once installed, the Smoker
Door should be able to be open and closed with ease.
13
14
15
39
51
51
11
16.
Parts Required :
1 x Grill Chambers Assembly (#13)
8 x M6x15 mm Screw (#A)
4 x M6x10 mm Screw (#D)
Installation :
• First, remove the twist tie on the front of the Grill
Chambers Assembly. Pull out the Smoker Electric
Wires and Smoker Temperature Sensor from the back
side of Control Panel. Note illustration 16A.
: Do not pinch or sandwich the electric wires
and/or temperature wire sensor during the assembly.
• Prepare the Grill Chambers Assembly to be mounted
to the Cart. Position the Cart next to the Grill
Chambers Assembly, with both facing the same
direction. Using a second person, prepare to lift the
Grill Chambers Assembly onto the Cart. Carefully
lift the Grill Chambers Assembly, and slowly lower
onto the Cart. Insert the Smoker Temperature Sensor
through the hole on the top of the Smoker Cabinet.
Note illustration 16B.
• Adjust the positioning as needed to align the screw
holes of the Grill Chambers Assembly to the Smoker
Cabinet (in the center). Secure using four screws (#D).
• Next, secure each Support Leg to the Grill Chambers
Assembly using two screws (#A) in each Support Leg.
17.
Installation :
• First, secure the Smoker Temperature Sensor into the
clip located inside the top of the Smoker Cabinet.
Note illustration 17A.
• Next, from the underside of the Grill Chambers, attach
the Smoker Electric Wires into the two clips, then pull
the rest along the back of the Smoker Cabinet, as
shown in illustration 17B.
• Lastly, insert the connector end of the Smoker Electric
Wires into the connection port on the bottom table
of the Cart. This completes the circuit to give power
to the Smoke Cabinet once connected to a power
source. Note illustration 17C.
3
3
16
17
17 17
16
3
13
13
3
12
18.
Parts Required :
1 x Electric Wires Back Cover (#41)
2 x M6x15 mm Screw (#A)
Installation :
• First, remove the pre-assembled two screws from the
bottom table of the Cart. Attach the Electrical Back
Cover to the back of the Smoker Cabinet.
: It is recommended to assemble the screws on
the top side first and then the bottom.
19.
Parts Required :
2 x Smoker Air Damper Pull Handle Assembly (#18)
1 x Smoker Top Air Damper - Left (#31.1)
1 x Smoker Top Air Damper - Right (#31.2)
8 x M5x10 mm Shoulder Bolt (#H)
Installation :
• Mount the Smoker Top Air Damper to the interior of
each Grill Chamber, as shown in illustration 19A.
• Next, insert each of the Smoker Air Damper Pull
Handles into the front panel of the unit, screwing
it into the mount hole of each Air Damper. Once
installed, each handle should slide from front to back
smoothly to control the airflow of each Air Damper.
Note illustration 19B.
20.
Parts Required :
2 x Charcoal Ash Tray Guides (#24)
1 x Charcoal Ash Tray (#25)
1 x Knob (#29)
1 x M5x10 mm Screw (#B)
4 x M6x10 mm Screw (#D)
Installation :
• Install the two Charcoal Ash Tray Guides to the
bottom-backside of the Charcoal Chamber using four
screws (#D). Note illustration 20A.
• Secure the Knob to the Charcoal Ash Tray, as shown in
illustration 20B.
• Lastly, slide the Charcoal Ash Tray into the guides, as
shown in illustration 20C.
IMPORTANT: Ensure the Charcoal Ash Tray is inserted
completely (towards the front) so there is no mess.
Adjust the screws for the guides, as needed, for best
alignment and positioning.
18
19
20 20
19
20
41
18
31.1
31.2
18
29
24 24
25
13
21.
Parts Required :
2 x Grease Drip Tray Guides (#26)
1 x Grease Tray (#27)
2 x Grease Cup (#28)
1 x Knob (#29)
1 x M5x10 mm Screw (#B)
4 x M6x10 mm Screw (#D)
Installation :
• Install the two Grease Drip Tray Guides to the bottom-
backside of the Gas Grill Chamber using four screws
(#D). Note illustration 21A.
• Secure the Knob to the Grease Tray, as shown in
illustration 21B.
• Slide the Grease Tray into the guides, as shown in
illustration 21C.
IMPORTANT: Ensure the Grease Tray is inserted
completely (towards the front) so that the hole of the
tray will flow grease into the Grease Cup. Adjust the
screws for the guides, as needed, for best alignment
and positioning.
• Slide a Grease Cup into the pre-installed guides along
the bottom of the Grease Tray. Note illustration 21D.
• Lastly, slide a Grease Cup into the pre-installed
guides along the bottom of the Smoke Cabinet
Assembly. Note illustration 21E.
22.
Parts Required :
4 x Grease Shields (#23)
6 x M6x10 mm Screw (#D)
6 x M6 Nuts (#J)
Installation :
• Mount each of the Grease Shields into the Main
Chambers: two in the Gas Grill Chamber and two in
the Charcoal Grill Chamber. Secure each screw with a
nut.
NOTE: When mounting the Grease Sheilds to the
center wall between Gas Grill Chamber and the
Charcoal Grill Chamber, use the same screws and nuts.
22
23
23
23
23
21 21
21
29
26
28
26
27
21
21
28
27
14
23.
Parts Required :
1 x Left Side Table (#8)
6 x Tool Hooks (#9)
1 x Right Side Table (#10)
6 x M6x10 mm Screw (#D)
Installation :
• On the edge of the Left Side Table with three holes,
install a Tool Hook into each hole along the edge.
Repeat the same steps for the Right Side Table.
24.
Parts Required :
8 x M6x15 mm Screw (#A)
Installation :
• Install four screws onto the left side of the unit,
leaving about 6mm / 1/4 inch out. Hang the Left
Side Table onto the screws, push down to lock into
position, then tighten the screws to secure. Repeat
same steps on the right side of the unit with the
Right Side Table.
25.
Parts Required :
2 x Cooking Grid Back Supports (#21)
2 x Cooking Grid Front Supports (#22)
16 x M4x10 mm Screw (#F)
Installation :
• Install a Cooking Grid Back Support to the back panel
of each Grill Chamber. Note illustration 25A.
• Install a Cooking Grid Front Support to the front panel
of each Grill Chamber. Note illustration 25B.
23
24
25
25
9
8 / 10
21
21
22
22
15
26.
Parts Required :
3 x Heat Tents (#14)
3 x Heat Tent Supports (#15)
6 x M4x10 mm Screw (#F)
Installation :
• First, install each of the three Heat Tent Supports to
the front side of Gas Main Chamber. See illustration
26A for proper location.
• Place each Heat Tent onto a Heat Tent Supports. Note
illustration 26B.
NOTE: The back end of the Heat Tents should be place
below the Cooking Grid Supports.
27.
Parts Required :
1 x Charcoal Tray Lifting System (#12)
1 x Charcoal Tray Lift Handle Assembly (#20)
4 x M6x10 mm Screw (#D)
2 x Hinge Pin (#K)
2 x R Clips (#L)
Installation :
• First, install the Charcoal Tray Lifting System to the
Charcoal Grill Chamber. Mount from the outside of
the Charcoal Grill Chamber. Note illustration 27A.
• Next, insert the Charcoal Tray Lift Handle Assembly
through the adjusting slot on the front of the unit
(see 27B.1). Continue to push the Handle rod through
the narrow "U" shaped bracket (see 27B.2), then align
the hole in the end of the wide "U" shaped bracket
(see 27B.3) located at the back of the Charcoal Main
Chamber. Join the Lift Handle and the "U" shaped
Brackets by inserting a Hinge Pin and securing with
an R-clip.
• Remove any twist ties located on the Charcoal Tray
Lifting System once all is secured.
TEST THE HANDLE: To adjust the Charcoal Tray Lifting
System to your desired height by moving the Lift
Handle to the left and then raising or lowering it.
26
26
27
27
15
14
14
14
12
20 20
27.1
27.3
27.2
16
28.
Parts Required :
3 x Black Gas Control Knobs (#16)
1 x Silver Smoker Control Knob (#17)
Installation :
• Place the three Black Control Knobs for each burner
onto each protruding valve stem, making certain
to align the flat portion of the stem with the flat
portion of the Control Knob. Push each Control Knob
onto the stem until it is firmly seated. Note 28A.
• Place the Silver Smoker Control Knob over the last
protruding valve stem, making certain to align the
flat portion of the stem with the flat portion of the
Control Knob. Push the Control Knob onto the stem
until it is firmly seated. Note 28B.
29.
Parts Required :
1 x Charcoal Tray Air Damper Handle Assembly (#19)
Installation :
• Install the Charcoal Tray Air Damper Handle Assembly
onto the Charcoal Chamber Air Damper. Once installed,
the handle should slide the Air Damper from left to
right smoothly to control the airflow of the Charcoal
Grill Chamber.
30.
Parts Required :
1 x Charcoal Tray (#11)
Installation :
• Place the Charcoal Tray onto the frame of the Charcoal
Tray Lifting System.
NOTE: The handles of the Charcoal Tray should be in
the front and back. This ensures the Charcoal Tray is
positioned correctly in the frame.
28 28
16 16 16 17
29
30
19
11
17
31.
Parts Required :
1 x Smoke Stack Lid (#3)
1 x Smoke Stack (#4)
2 x M6x10 mm Screw (#D)
2 x M6 Nuts (#J)
Installation :
• Remove the Smoke Stack Lid from the Smoke Stack.
Insert the Smoke Stack through the Charcoal Grill
Chamber Lid from the inside. Secure the Smoke Stack
from the outside of the Lid, and fasten with a nut
(from the inside). Screw the Smoke Stack Lid onto the
Smoke Stack fasten.
32.
Parts Required :
2 x Warming Rack (#5)
4 x M6x30 mm Screw (#M)
Installation :
• Protrude one screw through the Charcoal Grill
Chamber Lid from the outside, position the Warming
Rack, then insert the screw into the wire loop. Align
the front legs of the Warming Rack into the anchor
holes to secure. Repeat same installation for Warming
Rack in the Gas Grill Chamber.
33.
Part Required :
4 x Cooking Grids (#30)
Installation :
• Place the Cooking Grids onto the Cooking Grid
Supports of each Grill Chamber: two in the Gas Grill
Chamber, two in the Charcoal Grill Chamber.
NOTE: Both Grill Chambers have the same size
Cooking Grids.
31
32
33
3
4
5
30
30
30
30
18
34.
Parts Required :
2 x Thermometers (#1)
2 x Thermometer Bezels (#2)
Installation :
• First, remove the fiber washer and wing nut from
both Thermometers.
• Next, insert a Thermometer stem through a
Thermometer Bezel, then into the mounting hole on
the top of a Grill Chamber Lid. From the inside, place
the fiber washer and wing nut onto the mounting
thread pole and tighten by hand. Do not over
tighten. Repeat the same installation for the other
Grill Chamber Lid.
35.
Part Required :
2 x Lid Handles (#6)
4 x Large Handle Standoffs (#7)
8 x M6x15 mm Screw (#A)
Installation :
• First, assemble the Lid Handles by aligning and
inserting the Large Handle Standoffs onto each end
of the Lid Handles.
• Once assembled, mount the Lid Handle onto the Grill
Chamber Lids.
36.
Part Required :
1 x M6x10 mm Screw (#D)
Installation :
• The Hose Wire Retainer is pre-assembled on the
hose. Attach the Hose Wire Retainer to the front-left
Support Leg, as shown, using one screw.
34
36
35
2
2
1
1
7
76
19
37.
Part Required :
1 x AA Battery (#I)
Installation :
• Unscrew the igniter cap from the front control panel.
Insert the Battery into the battery slot with the
positive end (+) facing outward. Screw the cap back
onto panel.
• The unit is now completely assembled.
• It is highly recommended to wipe the exterior of your unit clean of debris, dirt, etc., using warm soapy water and a soft cloth.
• Remove all advertising and any glue residue.
• Use a vinegar and water solution to clean the glass on the Smoker Cabinet. Do not use a glass cleaner as this will leave a film
on the glass, which could bake on.
37
For all questions, inquiries, or customer support, please
contact Genesis International Corporation Pty Ltd.
+61 8 9248 9822 | service@genesiscorp.com.au
, ,
, ,
. ...//
780220524
©2022
Other manuals for MEMPHIS PBMEMU1
1
This manual suits for next models
1
Table of contents
Other Pit Boss Grill manuals
Pit Boss
Pit Boss PB700FB1 Installation instructions
Pit Boss
Pit Boss PB K22 71220 User manual
Pit Boss
Pit Boss 71220 Installation instructions
Pit Boss
Pit Boss Navigator PB700G User manual
Pit Boss
Pit Boss PB820ME User manual
Pit Boss
Pit Boss PB440TG1 Quick guide
Pit Boss
Pit Boss COMPETITION PB1230CS1 User manual
Pit Boss
Pit Boss PB700R2 Installation instructions
Pit Boss
Pit Boss PLATINUM KC COMBO PB1285KC Quick guide
Pit Boss
Pit Boss PRO Series Installation instructions
Pit Boss
Pit Boss PB340TGW1 Parts list manual
Pit Boss
Pit Boss Navigator PB850G User manual
Pit Boss
Pit Boss 850 PRO Series User manual
Pit Boss
Pit Boss Competition Series User manual
Pit Boss
Pit Boss PB100P Instruction Manual
Pit Boss
Pit Boss PBK13 Quick guide
Pit Boss
Pit Boss PB2BPGG User manual
Pit Boss
Pit Boss PBCSL200 Parts list manual
Pit Boss
Pit Boss LEXINGTON PB500LXW1 Quick guide
Pit Boss
Pit Boss PB260PSP2 Quick guide
Popular Grill manuals by other brands
Char-Griller
Char-Griller Kamado K55RCG owner's manual
Silvercrest
Silvercrest 379075 2110 operating instructions
MasterChef
MasterChef TF2201804-MC user manual
Range Master
Range Master 463724313 Product guide
Firesense
Firesense 62133 owner's manual
Beef Eater
Beef Eater 1500 Series Assembly and operating instructions
Silvercrest
Silvercrest SRGS 1300 A1 operating instructions
Char-Griller
Char-Griller Portable Table Top 2-2424 owner's manual
FLORABEST
FLORABEST FRG 45 A1 Assembly and operating instructions
Silvercrest
Silvercrest SRG 1200 A1 operating instructions
Silvercrest
Silvercrest SKGE 2000 C3 operating instructions
MasterChef
MasterChef PRIME Series Assembly manual
