PITTMAN PPI-XTREME20 User manual

PPI-XTREME20 OWNER’S MANUAL
IT IS HIGHLY RECOMMENDED THAT YOU READ AND FOLLOW
THE INFORMATION CONTAINED IN THIS MANUAL BEFORE
INITIAL SET UP.
Queen Fab ic Ext eme 20" Ai Matt ess
with Built-In Elect ic Ai Pump
PPI-XTREME20_Owners Manua _Layout 1 1/7/16 12:08 PM Page 1

WARNING: THIS PRODUCT IS NOT FLAME RESISTANT. THIS BED
CONTAINS PLASTIC. DO NOT PLACE AIR BED NEAR OPEN FLAME OR
OTHER SOURCE OF IGNITION.
WARNING: This is not a toy. To avoid risk of fire, burns, injury or shock, it
should not be played with or placed where small children can reach it.
• Unplug cord when not in use.
• Pump is an electrical device. Do not use in or around water.
• Do not attempt to disassemble, repair, or service the pump. No
serviceable parts are contained inside. Contact Pittman Products
International at 15330 Valley View Ave, Suite 2
La Mirada, California 90638 for service or repair.
WARNING:
• This is not a water toy or flotation device. Use as a bed only.
• Not recommended for use by children under three (3) years of age.
• This bed is not intended for infants or persons with limited mobility. They may
roll off of the bed and become entrapped between the bed and walls and
suffocate.
• Do not use this bed on abrasive surfaces or near pointed, sharp or protruding
objects. Bed may puncture. Remove all sharp objects from area the bed will be
used in.
• Do not step or jump on bed or use as a trampoline. Standing, jumping or
walking on the bed may result in injury and/or damage or puncture the bed.
• Make sure surface is clean of any debris, sharp objects or protrusions or place
bed in a safe area before use making sure that there are no sharp edges, steps,
drops, or breakable items nearby. Use on flat surfaces only. Bed may tip over
on uneven surfaces.
CONTENTS
1. Pittman air mattress with built in AC air pump
2. Repair patch kit
3. Carrying bag
SET UP GUIDE
Your Pittman air bed has a built in air pump as well as a
2 Stage Valve. The 2 Stage Valve is used for optional
inflation and deflation.
This Valve is constructed in three parts:
1. Bladder valve with valve lip
2. Middle valve
3. Upper cap
INFLATION
1. Place your bed on a flat surface free of debris, obstructions and sharp
objects.
2. Spread the bed out so that it can fill easily. Allowing the bed to "unfold"
itself may place an unnecessary strain on the bed and the pump.
3. Make sure Middle Valve (2) and Upper Cap (3) are closed.
4. Turn inflate/deflate valve (B) on the built in pump to the “inflate”
position to inflate the bed.
5. Turn inflate/deflate valve to the “off” position once the desired firmness
has been achieved.
3
2
1
PPI-XTREME20_Owners Manua _Layout 1 1/7/16 12:08 PM Page 2

A
OPTIONAL INFLATION PROCEDURE
This Pittman air bed comes with a secondary inflate/deflate option (A) for use
with portable air pumps as a back up to the installed automatic pump. To use a
portable air pump, follow these instructions:
1. The middle valve (2) must be pushed in tightly to the bladder valve
(1). The upper cap (3) must be removed from the middle valve in
order to inflate.
2. Ensure inflate/deflate valve (B) is in the off position.
3. Insert portable pump into the middle valve (2). (Use proper pump
adapter fitting if needed)
3. Remove portable pump and switch off. (Middle valve (2) has a built
in stopper that will automatically close when pump is removed
stopping any air loss)
4. Replace the upper cap (3).
NOTE: For faster inflate open middle valve (2) and insert pump into bladder
valve (1) and fill until almost fully inflated. Once the bed is almost fully
inflated, close middle valve (2) then continue filling until desired firmness.
Close upper cap (3) when finished.
DEFLATION
1. Turn inflate/deflate valve (B) to the deflate position to deflate bed.
2. Deflate until bed is fully deflated. For faster deflation, you may open
the middle valve (2).
3. Turn inflate/deflate valve to the off postion to turn pump off.
4. Fold bed according to Folding Instructions below and place into
carrying bag and store until next use.
B
PPI-XTREME20_Owners Manua _Layout 1 1/7/16 12:08 PM Page 3

FOLDING INSTRUCTIONS
1. Upon complete deflation, lay bed on flat surface with sleeping surface
facing upwards and fold according to the steps below.
1 2
3 4
5 6
7 8
Pump Side
*actual bag may vary
PPI-XTREME20_Owners Manua _Layout 1 1/7/16 12:08 PM Page 4

CARE AND MAINTENANCE
1. Inspect your bed before each use.
2. eep your bed away from any sharp or protruding objects. Large
cuts, tears or snags may not be repairable and will not be covered by
your warranty.
3. A repair patch kit has been included in case of incidental damage to
your bed. Please follow repair instructions carefully.
4. When not in use store bed in a clean, dry place out of extreme
temperatures.
CLEANING
DO NOT SUBMERGE BED IN WATER! For spot cleaning, use a clean
damp cloth to wipe the surface of the bed. Apply a clear liquid dish
detergent without dye if necessary. Wet stained area thoroughly; gently
massage stained area with detergent. Blot the area to remove staining
substance. Rinse thoroughly and blot dry. Allow your bed to air dry
completely after cleaning and before storing.
ADDITIONAL INFORMATION
IN CASE OF AIR LEAKAGE
Please check the following if there is an air leak.
1. Is the inflate/deflate valve on built in pump turned to inflate position?
2. Is the secondary inflate/deflate valve cap closed?
A repair patch kit has een included for minor repairs.
REPAIRING AN AIR LEAK
1. Wipe bed with mild soap water over area to find possible air leak. DO
NOT SUBMERGE MATTRESS IN WATER! If there is a leak
bubbles will form around leakage area.
2. Follow cleaning instructions for leak area.
3. Use included patch kit to cut a suitable sized patch for leak. Make
sure to round the edges of repair patch to avoid peeling.
4. Apply glue to patch area and around leakage area.
5. Press patch firmly over the puncture area.
6. Wait one hour before inflating.
Please Note:
Stretching is a natural occurence of new vinyl. During the first days of use, this
air bed may become soft and require additional inflation to maintain desired
firmness.
PPI-XTREME20_Owners Manua _Layout 1 1/7/16 12:08 PM Page 5

WARRANTY DISCLAIMER
Pittman Air Beds are warranted against defects in material and workmanship for
a period of One Year from the date of purchase. Problems covered by the
warranty include failure of the pump, seams or the valve. Punctures or wear to
the bed due to use or abuse are not covered.
It is normal for an airbed that has been inflated for extended periods to require
the addition of air after a few days. Air will be lost from the bed through the
material over time. Also, cooling of the air around the bed will cause the air
inside the bed to contract, and the bed will be softer and may need refilling.
To receive a replacement air bed under Pittman Products International’s One
Year Warranty, you will need to:
• All returns must have a Returned Goods Authorization number
(RGA). Every package must be clearly marked with the RGA number.
RGA numbers are good for 30 days from the date of issuance.
Products returned without viewable RGA numbers will be refused. No
returns on special order, clearance or discounted items. Returned
products is subject to a 20% Re-Box/Restocking fee. Products must be
properly packed to prevent shipping damage. All returned product
must be shipped pre-paid.
• Send entire product to Pittman Products International with a letter
stating:
- The nature of the problem with the bed and the model
number.
- Your name, return shipping address and a daytime phone
number.
• Send us a copy of the original sales receipt.
The purchase date on the receipt must be within One Year of the date you ship
the bed to us.
Please ship the bed, letter and copy of receipt, and UPC Symbol, via courier
(e.g. UPS, FedEx Ground) or Insured Post, to:
Pittman Products International
Attn: Returns
15330 Valley View Ave, Suite 2
La Mirada, California 90638
Pittman Products International is not responsi le for returned shipments
lost in transit. You are encouraged to use a shipment system that offers you
a tracking num er. Please allow 6 to 8 weeks for replacement. Customer is
responsi le for all return shipping costs.
PPI-XTREME20_Owners Manua _Layout 1 1/7/16 12:08 PM Page 6

EXCEPT FOR THE EXPRESS LIMITED WARRANTY SET FORTH ABOVE,
PITTMAN PRODUCTS INTERNATIONAL MA ES NO EXPRESS OR
IMPLIED WARRANTIES IN THIS AGREEMENT OR OTHERWISE. TO
THE FULLEST EXTENT PERMITTED BY LAW, PITTMAN PRODUCTS
INTERNATIONAL DISCLAIMS ALL WARRANTIES, WRITTEN,
EXPRESSED OR IMPLIED, INCLUDING ALL WARRANTIES OF
MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
PITTMAN PRODUCTS INTERNATIONAL EXPRESSLY DISCLAIMS ANY
AND ALL LIABILITY TO PURCHASER FOR ANY CONSEQUENTIAL
DAMAGES, DAMAGES FOR LOSS OF USE, LOSS OF PROFITS,
PROPERTY DAMAGE, OR ANY OTHER INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF THIS
AGREEMENT OR THEIR OPERATION, FUNCTION OR
CHARACTERISTICS OF THE PRODUCTS PURCHASED HEREUNDER.
IT IS EXPRESSLY UNDERSTOOD THAT THE LIMITED WARRANTY SET
FORTH ABOVE IS THE SOLE AND EXCLUSIVE REMEDY OF
PURCHASER. NOT WITHSTANDING THE TERMS OF ANY LIMITED
WARRANTY, AND/OR IN THE EVENT ANY LIMITED WARRANTY
PROVIDED TO THE PURCHASER FAILS OF ITS ESSENTIAL PURPOSE,
IN NO EVENT WILL PITTMAN PRODUCTS INTERNATIONAL ENTIRE
LIABILITY TO PURCHASE EXCEED THE PURCHASE PRICE ACTUALLY
PAID BY PURCHASER FOR THE PRODUCTS HEREUNDER, OR ANY
DEFECTIVE PORTION THEREOF, WHICHEVER IS THE LESSER
AMOUNT.
Pittman Products International neither assumes nor authorizes any representative
or other person to assume any obligation or liability other than those expressly
set forth herein.
YOUR RIGHT UNDER STATE LAW: This warranty gives you specific rights
and you may also have other rights, which vary from state to state.
© 2016 Pittman Products International
All rights reserved.
Made in China.
Our Customer Service Department is available Monday - Friday, 9 AM to 5 PM
Pacific Standard Time, to answer any questions you may have about your new
Pittman air bed product please call us toll free at 1 [phone]. U.S.A.
15330 Valley View Ave, Suite 2
La Mirada, California 90638
1 [phone]
www.pittmanproducts.com
PPI-XTREME20_Owners Manua _Layout 1 1/7/16 12:08 PM Page 7

PPI-XTREME20_Owners Manua _Layout 1 1/7/16 12:08 PM Page 8