PITTMAN PPI-QUDH1 User manual

PPI-QUDH1 & PPI-QCDH2
OWNER’S MANUAL
IT IS HIGHLY RECOMMENDED THAT YOU READ AND FOLLOW
THE INFORMATION CONTAINED IN THIS MANUAL BEFORE
INITIAL SET UP.
PPI-QUDH1 & QCDH2_Owners Manual_Layout 1 9/19/14 5:21 PM Pa e 1

WARNING: THIS PRODUCT IS NOT F AME RESISTANT. THIS BED
CONTAINS P ASTIC. DO NOT P ACE AIR BED NEAR OPEN F AME OR
OTHER SOURCE OF IGNITION.
WARNING: This is not a toy. To avoid risk of fire, burns, injury or shock, it
should not be played with or placed where small children can reach it.
• Unplug cord when not in use.
• Pump is an electrical device. Do not use in or around water.
• Do not attempt to disassemble, repair, or service the pump. No
serviceable parts are contained inside. Contact Pittman Products
International at 15330 Valley View Ave, Suite 2
a Mirada, California 90638 for service or repair.
WARNING:
• This is not a water toy or flotation device. Use as a bed only.
• Not recommended for use by children under three (3) years of age.
• This bed is not intended for infants or persons with limited mobility. They may
roll off of the bed and become entrapped between the bed and walls and
suffocate.
• Do not use this bed on abrasive surfaces or near pointed, sharp or protruding
objects. Bed may puncture. Remove all sharp objects from area the bed will be
used in.
• Do not step or jump on bed or use as a trampoline. Standing, jumping or
walking on the bed may result in injury and/or damage or puncture the bed.
• Make sure surface is clean of any debris, sharp objects or protrusions or place
bed in a safe area before use making sure that there are no sharp edges, steps,
drops, or breakable items nearby. Use on flat surfaces only. Bed may tip over
on uneven surfaces.
CONTENTS
1. Pittman air bed with built in AC air pump
2. Repair patch
3. Carrying bag
SET UP GUIDE
Your Pittman air bed has a built in air pump as well as a
2 Stage Valve. The 2 Stage Valve is used for optional
inflation and deflation.
This Valve is constructed in three parts:
1. Bladder valve with valve lip
2. Middle valve
3. Upper cap
INFLATION
1. Place your bed on a flat surface free of debris, obstructions and sharp
objects.
2. Spread the bed out so that it can fill easily. Allowing the bed to "unfold"
itself may place an unnecessary strain on the bed and the pump.
3. Make sure Middle Valve (2) and Upper Cap (3) are closed.
4. Turn inflate/deflate valve (B) on the built in pump to the “inflate”
position to inflate the bed.
5. Turn inflate/deflate valve to the “off” position once the desired firmness
has been achieved.
3
2
1
PPI-QUDH1 & QCDH2_Owners Manual_Layout 1 9/19/14 5:21 PM Pa e 2

A
OPTIONAL INFLATION PROCEDURE
This Pittman air bed comes with a secondary inflate/deflate option (A) for use
with portable air pumps as a back up to the installed automatic pump. To use a
portable air pump, follow these instructions:
1. The middle valve (2) must be pushed in tightly to the bladder valve
(1). The upper cap (3) must be removed from the middle valve in
order to inflate.
2. Ensure inflate/deflate valve (B) is in the off position.
3. Insert portable pump into the middle valve (2). (Use proper pump
adapter fitting if needed)
3. Remove portable pump and switch off. (Middle valve (2) has a built
in stopper that will automatically close when pump is removed
stopping any air loss)
4. Replace the upper cap (3).
NOTE: For faster inflate open middle valve (2) and insert pump into bladder
valve (1) and fill until almost fully inflated. Once the bed is almost fully
inflated, close middle valve (2) then continue filling until desired firmness.
Close upper cap (3) when finished.
DEFLATION
1. Turn inflate/deflate valve (B) to the deflate position to deflate bed.
2. Deflate until bed is fully deflated. For faster deflation, you may open
the middle valve (2).
3. Turn inflate/deflate valve to the off postion to turn pump off.
4. Fold bed according to Folding Instructions below and place into
carrying bag and store until next use.
B
PPI-QUDH1 & QCDH2_Owners Manual_Layout 1 9/19/14 5:21 PM Pa e 3

FOLDING INSTRUCTIONS
1. Upon complete deflation, lay bed on flat surface with sleeping surface
facing upwards and fold according to the steps below.
1 2
3 4
5 6
7 8
Pump Side
*actual bag may vary
PPI-QUDH1 & QCDH2_Owners Manual_Layout 1 9/19/14 5:21 PM Pa e 4

CARE AND MAINTENANCE
1. Inspect your bed before each use.
2. Keep your bed away from any sharp or protruding objects. arge
cuts, tears or snags may not be repairable and will not be covered by
your warranty.
3. A repair patch has been included in case of incidental damage to your
bed. Please follow repair instructions carefully.
4. When not in use store bed in a clean, dry place out of extreme
temperatures.
CLEANING
DO NOT SUBMERGE BED IN WATER! For spot cleaning, use a clean
damp cloth to wipe the surface of the bed. Apply a clear liquid dish
detergent without dye if necessary. Wet stained area thoroughly; gently
massage stained area with detergent. Blot the area to remove staining
substance. Rinse thoroughly and blot dry. Allow your bed to air dry
completely after cleaning and before storing.
ADDITIONAL INFORMATION
IN CASE OF AIR LEAKAGE
Please check the following if there is an air leak.
1. Is the inflate/deflate valve on built in pump turned to inflate position?
2. Is the secondary inflate/deflate valve cap closed?
A repair patch has een included for minor repairs.
REPAIRING AN AIR LEAK
1. Wipe bed with mild soap water over area to find possible air leak. DO
NOT SUBMERGE BED IN WATER! If there is a leak bubbles will
form around leakage area.
2. Follow cleaning instructions for leak area.
3. Use included patch to cut a suitable sized patch for leak. Make sure to
round the edges of repair patch to avoid peeling.
4. Press patch firmly over the puncture area.
5. Wait one hour before inflating.
Please Note:
Stretching is a natural occurence of new vinyl. During the first days of use, this
air bed may become soft and require additional inflation to maintain desired
firmness.
PPI-QUDH1 & QCDH2_Owners Manual_Layout 1 9/19/14 5:21 PM Pa e 5

WARRANTY DISCLAIMER
Pittman Air Beds are warranted against defects in material and workmanship for
a period of thirty days from the date of purchase. Problems covered by the
warranty include failure of the pump, seams or the valve. Punctures or wear to
the bed due to use or abuse are not covered.
It is normal for an airbed that has been inflated for extended periods to require
the addition of air after a few days. Air will be lost from the bed through the
material over time. Also, cooling of the air around the bed will cause the air
inside the bed to contract, and the bed will be softer and may need refilling.
To receive a replacement air bed under Pittman Products International’s Thirty
Day Warranty, you will need to:
• Send entire product to Pittman Products International with a letter
stating:
- The nature of the problem with the bed and the model
number.
- Your name, return shipping address and a daytime phone
number.
• Cut from the box the UPC Symbol. (If the carton is not available, state
that you do not have the carton in the letter).
• Send us a copy of the original sales receipt.
The purchase date on the receipt must be within 30 days of the date you ship the
bed to us.
Please ship the bed, letter and copy of receipt, and UPC Symbol, via courier
(e.g. UPS, FedEx Ground) or Insured Post, to:
Pittman Products International
Attn: Returns
15330 Valley View Ave, Suite 2
a Mirada, California 90638
Pittman Products International is not responsi le for returned shipments
lost in transit. You are encouraged to use a shipment system that offers you
a tracking num er. Please allow 6 to 8 weeks for replacement. Customer is
responsi le for all return shipping costs.
PPI-QUDH1 & QCDH2_Owners Manual_Layout 1 9/19/14 5:21 PM Pa e 6

EXCEPT FOR THE EXPRESS IMITED WARRANTY SET FORTH ABOVE,
PITTMAN PRODUCTS INTERNATIONA MAKES NO EXPRESS OR
IMP IED WARRANTIES IN THIS AGREEMENT OR OTHERWISE. TO
THE FU EST EXTENT PERMITTED BY AW, PITTMAN PRODUCTS
INTERNATIONA DISC AIMS A WARRANTIES, WRITTEN,
EXPRESSED OR IMP IED, INC UDING A WARRANTIES OF
MERCHANTABI ITY AND/OR FITNESS FOR A PARTICU AR PURPOSE.
PITTMAN PRODUCTS INTERNATIONA EXPRESS Y DISC AIMS ANY
AND A IABI ITY TO PURCHASER FOR ANY CONSEQUENTIA
DAMAGES, DAMAGES FOR OSS OF USE, OSS OF PROFITS,
PROPERTY DAMAGE, OR ANY OTHER INCIDENTA ,
CONSEQUENTIA OR SPECIA DAMAGES ARISING OUT OF THIS
AGREEMENT OR THEIR OPERATION, FUNCTION OR
CHARACTERISTICS OF THE PRODUCTS PURCHASED HEREUNDER.
IT IS EXPRESS Y UNDERSTOOD THAT THE IMITED WARRANTY SET
FORTH ABOVE IS THE SO E AND EXC USIVE REMEDY OF
PURCHASER. NOT WITHSTANDING THE TERMS OF ANY IMITED
WARRANTY, AND/OR IN THE EVENT ANY IMITED WARRANTY
PROVIDED TO THE PURCHASER FAI S OF ITS ESSENTIA PURPOSE,
IN NO EVENT WI PITTMAN PRODUCTS INTERNATIONA ENTIRE
IABI ITY TO PURCHASE EXCEED THE PURCHASE PRICE ACTUA Y
PAID BY PURCHASER FOR THE PRODUCTS HEREUNDER, OR ANY
DEFECTIVE PORTION THEREOF, WHICHEVER IS THE ESSER
AMOUNT.
Pittman Products International neither assumes nor authorizes any representative
or other person to assume any obligation or liability other than those expressly
set forth herein.
YOUR RIGHT UNDER STATE AW: This warranty gives you specific rights
and you may also have other rights, which vary from state to state.
© 2014 Pittman Products International
All rights reserved.
Made in China.
Our Customer Service Department is available Monday - Friday, 9 AM to 5 PM
Pacific Standard Time, to answer any questions you may have about your new
Pittman air bed product please call us toll free at 1 [phone]. U.S.A.
15330 Valley View Ave, Suite 2
a Mirada, California 90638
1 [phone]
www.pittmanproducts.com
PPI-QUDH1 & QCDH2_Owners Manual_Layout 1 9/19/14 5:21 PM Pa e 7