Pivot PA-SK1 User manual

USER GUIDE
PA-sk1
Better Connection. Better Protection.
[ Issued 08.18.2020 Version R01 ]

2.
PA-SK1 | User Guide
For optimal performance and maximum satisfaction with your PIVOT case, please follow
this set of simple recommendations to ensure proper deployment and superior device
protection.
WARNING: Your PIVOT case is designed to hold your device firmly to protect against
accelerated impacts. Once installed, your device will be held securely on all sides. It is not
intended to come out easily. When you get a PIVOT case, it means you’re getting the
best. PIVOT products maximize protection and minimize the need to remove the device
from your PIVOT case.
If you need to remove your device, please refer to this document or visit PIVOT online for
instructions to avoid unnecessary damage to your device and PIVOT case.
Read Before Use
Thermal Control
Tough Protection
Air Cushion Lightweight
Keyboard Compatible Stylus Support
A-Z
[ Issued 08.18.2020. Version R01 ]

3.
1)Clean camera surface and surrounding using manufacturer’s
recommended methods.
2)Check for fit/compatibility with device and PIVOT case
before final application.
3)Remove PA-CB-1 adhesive backing, align the hole on
the sliding camera blocker with device camera and
lightly place blocker into position.
4)Test for proper function and adjust if necessary.
Press firmly when complete.
Installing PA-CB-1 Camera Blockers
Camera Blocker:

4.
1)Clean camera surface and surrounding using manufacturer’s
recommended methods.
2)Check for fit/compatibility with device and PIVOT case
before final application.
3)Remove PA-CB-2 adhesive backing, align the hole on
the sliding camera blocker with device camera and
lightly place blocker into position.
4)Test for proper function and adjust if
necessary. Press firmly when complete.
Installing PA-CB-2 Camera Blockers
!Pro Tip!
Remember to adjust ambient
light sensor setting in the
device menu after installing.

5.
Installing PA-SS-1104 Security Stickers
Installing PA-MB-1 Microphone Blocker 3.5mm
1)The PA-MB-1 fits only standard 3.5mm headphone jacks.
2) Remove the audio block from the case.
If the sliding camera blockers are not compatible with
device or case, use PA-SS-1104 Security Stickers.
3) Insert the PA-MA-1 into the audio jack of the device.
4)Remove the PA-MB-1 to restore microphone
function. This may require first removing the protective
case depanding on device type and case.
Beginning with the bottom edge near the charging
port, press firmly using your thumbs to disengage
the case seal. Continue carefully pressing around the
edges of the case to release the device in the order
shown. Do not attempt to pry or force the device
from the case.
1. Start at the bottom and move left
2. Continue around the top edge
3. Release the right edge to remove device
Removing Device
Microphone Blocker:
Security Stickers:
1
2
3
Top
Bottom
Left
Right

6.
Installing PA-SS-1104 Security Stickers
Put the stickers to cover the rear and front camera.
Installing Device
Align device camera and buttons with the
corresponding access points in the case body.
Ensure that nothing is misaligned or otherwise
obstructing the installation of the device into
the case body.

7.
Press firmly around all edges of the front
frame to engage the locking tabs. When
pressing each edge into a locked position,
follow the sequence as illustrated here. Do
not use tools or attempt to force the
installation process.
1. Start at the bottom and move left.
2. Continue around the top edge.
3. Complete installation by securing the
right edge.
(Reverse this process for removing the
device.)
Place the device into the back of the case
body. Ensure the device is properly aligned
inside of the case back. If misaligned,
remove and try again. Press the front frame
of the case body over the front face of the
device. Small locking tabs on the front and
back case will begin to engage.
1
2
3
Top
Bottom
Left
Right

8.
Thank you.
To learn more about your PIVOT case, please visit pivotcase.com for instructional videos, product
support and additional information about PIVOT products. You’ll find valuable online resources
provided to enhance your user experience and see the complete line of PIVOT products.
Additional Information
Learn more at:
PIVOTCASE.COM
TM and © 2019 FlyBoys Inc. All rights reserved.
Designed in USA. Printed in USA.
PIVOT SUPPORT
If you have questions please contact PIVOT Support.
[email protected]
www.pivotcase.com/support
1-888-4-FLYBOYS (1-888-435-9269)
www.youtube.com/c/pivotcasevideo