Pixel K90 User manual

K90专业影视灯使用说明书
一、承蒙您惠顾
为正确使用本产品，请先仔细阅读此说明书，并熟悉其操作步骤。注意保存此说明书，以备参考。
二、产品简介
LED专业摄影灯是由微电脑芯片控制，显示屏状态显示，输出功率无级调光，单色温5600K,双色温
3200K/5600K,安全隔离直流电压供电。可挂接摄影机电池，为室外拍摄提供方便。内置温度保护电路，
内置自然散热系统。
三、技术参数
四、操作面板名称
五、操作说明
1、打开灯光:
1
适配器供电:请把电源适配器的DC头插入适配器接口［ ］，再把适配器的电源线插入电源插座并
且连接110V60HZ或220V50Hz交流电,按下适配器标识侧开关，即可打开影视灯。
2
注: 打开电源开关后，影视灯按最后保存的参数进入工作状态，显示屏显示影视灯当前的工作参数。
2、调节亮度/双色温切换:
1开机状态下旋转亮度微调旋钮［ ］此时对LED功率进行调整，显示屏会显示当时的功率，可调节
的范围为1%-100%。按一下旋钮中间的切换键，即可进入双色温调整模式，再微调旋钮对LED色温
进行调整范围为：3200K-5600K。
2开机状态下按一下亮度快速调整按钮［ ］会让灯在1%25% 50%75%100% 五个功率档位循环调整。
15V
按下频道设置按钮［ ］显示屏上的CH一频道会闪烁，再旋转频道调节旋钮可以调节CH01-CH48
循环调整，调到需要的频道后再按一下频道设置按钮［ ］或等4秒后自动确认为当前频道。
注: 第一次调整会让灯从原始的功率提高到相近的档位。
注: 调节任何一台灯的功率都会同步到相同频道相同组别的灯。
3、频道组别的设置:
按一下组别切换［ ］进入下一组，共分A、B、C、D、E、F、可以循环切换，显示屏上会显示出当
前组别。 在切换组别时LED灯会调出不同组别的最后一次数据作为当前值并调整亮度。
1
2
CH
CH
GP
1)本型号的灯可以设置1-48联控频道，不同频道的灯调节不会相互干扰。
2 )本型号的灯可以设置为A .B.C.D.E.F.组别。每个组别可以同时有若干只灯。
3 )对同一组别的灯进行无线联控时，需要设置为同一频道。
注:调节任何一台灯的功率都会同步到相同频道相同组别的灯。
4、无线联控:
首先保证主控灯和受控灯处于同一频道。
同一组别的亮度调整，只要调整同一组别的任何一台灯，同频同组的其他影视灯将会跟随调整灯同步
调整。
不同组别的亮度调整。
1
2
3
进入遥控模式: 按下遥控模式［ ］显示屏上的当前受控组别标识会闪烁
按组别切换［ ］可以切换当前受控组别并显示对应组别的当前设置。GP
在组别标识闪烁时可以调整对应闪烁组别的灯光亮度，主控灯设置不受影响。
再次按下遥控模式或4秒不调整会自动退出遥控模式。
5、关掉灯光时会自动保存当前的参数设置，以便再次使用时快速恢复上次的拍摄场景灯光。
六、注意事项
1、请勿将摄影灯放置在高温高湿的地方。
2、请勿将产品浸入水中或暴露于雨中。
3、使用电池的注意事项:
切勿将电池投入火中或加热升温。
当电量用尽时电池容易漏液。所以为了避免产品受损，请在长期不使用本产品或电量用尽时取出
电池。
1
2
七、装箱清单
序号 名称 数量
1LED灯体 1套
4色片
2输入电源线 1条 5说明书
3适配器 1只 6合格证保修卡
1份
1份
1台
序号 名称 数量
感谢您购买品色公司产品并阅读本说明书，如有任何疑问可以向当地经销商咨询，或登入
http://www.pixelhk.com.cn查询。
制 造 商: 东莞市宝易电子科技有限公司
地 址： 东莞市大朗镇金朗南路255号
电 话： 400-8084899
执行标准： Q/PSKJ 004-2016
Made in china
K90
AC:100-240V50/60Hz DC: 15V 6A
90W
10400LM
P1-P100无极调光
CRI>95
5600K
V口电池
5万小时以上
28.9x28.7x5.5CM
K90S
AC:100-240V50/60Hz DC: 15V 6A
90W
10400LM
CRI>95
3200K~5600K
28.9x28.7x5.5CM
1.95KG 1.95KG
有 有
P1-P100无极调光
V口电池
5万小时以上
型 号
输入电源
输出功率
流 明
调节范围
显色指数
色 温
电 池
产品尺寸
重 量
温度保护
LED灯寿命
挡光板
柔光板吸附点
LED灯珠
2、显示屏
3、组别切换
4、亮度快速调整
5、摇控模式
6、频道设置
1、锂电池安装口 散热孔
7、调节亮度/色温 /切换开关
8、电源转换开关
(适配器供电/关/电池供电)
9、适配器接口
正视图 后视图
CH
电池供电: 请在锂电池安装口上安装电池，按下电池标识侧开关，即可打开影视灯。
100%
5600K
01
CH
A

Professional LED Photography Light
K90
Instruction Manual
Overview
Product Introduction
Specification
Name of Parts
Operate Instruction
1.Turn On:
1
2
Caution: After turned on the power,the light keeps all the setting as last power on status.
2.Brightness /Color Temperature Adjust Dial:
1
2
Caution: The first press this button will go to the closest power level base on the existing power.
3.Channel and Group Setting:
1
2
CH
1)This light can be set between 1- 48 channel, no interference if the lights in different channel.
2)This light can be set between A.B.C.D.E.F. group, each group can have a lot of lights.
3)To control the lights in the same group, you have to set in the same channel first.
4.Wireless Control:
1
2
Make sure the master and slave light in the same channel.
3Brightness adjust in the different group.
Enter to control mode: Press the control mode button［ ］the existing group icon on display will flash.
Press group setting button［ ］switch to the group that you want to control.GP
You can adjust the brightness during the group icon keep flashing. This master light setting will not effect.
Press again control mode button or wait for 4sec to exit the control mode.
Caution
1.Do NOT put the light under high temperature and high humidity area.
2..Do NOT put the light in water or use under raining.
3.Caution when using battery:
Do NOT throw the battery in fire or increase the temperature.
1
2
Package included
Series Name Qty
1LED Light 1PC 4Color Filter
2Input Power Cable 1PC 5Manual
3Adaptor 1PC 6Warranty Card
1PC
1PC
1PC
Series Name Qty
Thank you for choosing Pixel Enterprise Limited product and read this user manual. Should you have any
questions, please contact the local dealer or visit our
website:http://www.pixelhk.com
Heat Reduce Holes
7.Bright and Color
Adjust Switch
8.Power Switch
(Adapter Supply/
Off/Battery Supply)
9.Adaptor Socket
Front Side Rear Side
Reflector
Reflector Holding
Point LED Beans
1.Lithium Battery
clip
2.Display
3.Group Setting
4.Quick Brightness
Adjust
5.Control Mode
6.Channel Setting
Model
Input Power
Output Power
Lumen
Adjust Range
Color Rendering Index
Color Temperature
Battery
LED Life
Dimension
K90
AC:100-240V50/60Hz DC: 15V 6A
90W
10400LM
P1-P100 SteplessAdjust
CRI>95
5600K
V Type Battery
50,000 Hrs
28.9x28.7x5.5CM
K90S
AC:100-240V50/60Hz DC: 15V 6A
90W
10400LM
CRI>95
3200K~5600K
28.9x28.7x5.5CM
Net Weight 1.95KG 1.95KG
Temperature Protect Yes Yes
P1-P100 SteplessAdjust
V Type Battery
50,000 Hrs
Before using this product, you must read the manual and fully understand how to use it and ensure
that you can easily handle the operation method and also use it properly.
This LED light is controlled by MCU. Everything shows on the display like the status, output power,
power adjustment, single color temperature 5600K, dual color temperature 3200K-5600K; Safety to
isolate power supplied by DC voltage. This LED light can use the recorder battery which is more
convenience to use for outdoor shooting. Internal temperature protects circuit and heat reduces system.
Battery Supply: Please install battery on the lithium battery clip. Press the battery icon power switch to
turn on the LED light.
Adaptor Supply: Please plug the DC adaptor to the adaptor socket, then adaptor cable connect to 110v
60Hz or 220V 50Hz.Press to adaptor icon power switch to turn on the LED light.
Press the quick brightness adjust button. Recycle to change to power between 1%,25%，50%,75% and
100%.
Caution: Adjust one of the LED light power, the power will sync to the other LED light which under the same
channel and group.
Press Channel Setting Button[ ], CH on display will flash, then rotate the channel adjust button to
change the channel between CH01- CH48. Press the channel setting button or wait for 4sec to confirm
the channel.
Press Group Setting [ GP ] change to the next group, total A,B,C,D,E,F groups and display shows the
existing group. When switching to the different group, the LED will also change the setting base on the
new group
Dim the brightness adjust dial to change the light power.Display will show the existing light power and
adjust range in 1%-100%. Press once switch to color temperature mode, dim the dial again to change
the color between 3200K-5600K.
Caution: Adjust one of the LED light power, the power will sync to the other LED light which under the same
channel and group.
Brightness adjust in the same group. adjust any light under the same group, the other light under the
same group and same channel will adjust too.
5.Turn off the light power will keep the existing setting, turn on the light again in the next time; all the setting
will be the same.
When use all the battery power, the battery easily to leak. To avoid this case, please take out the
battery from the product when long time not using the product.
100%
5600K
01
CH
A