Plättner ES1000W-AF8 User manual

Operating manual
Electronic Series Switch ES1000W-AF8
Usage instructions
Appropriate use
The ES1000W-AF8 is intended exclusively for lighting purposes.
It can be used in all classical switching circuits, such as switch-off,
alternating or cross circuits and in impulse relay circuits. The
ES1000W-AF8 extends these circuits to include series switching in a
very simple manner.
This allows independent control of two lamps, which can otherwise
only be implemented at a significantly higher cost by using classical
series circuits. With the ES1000W-AF8 the existing installation only
needs to be extended. Only the added lamp must be newly connected.
The small dimensions allow the ES1000W-AF8 to be installed (using
spring terminal technology) e.g. in junction boxes, baldachines etc.
The ES1000W-AF8 electronic series switch is suitable for energy saving.
The intended use according to the application conditions of the
ES1000W-AF8 according to DIN EN 60699-2-1.
The ES1000W-AF8 is intended for installation in lighting systems.
The ES1000W-AF8 is suitable for use with resistive loads (filament
lamps, high voltage halogen lamps), energy-saving lamps, LED lamps
with associated driver, low voltage halogen lamps with associated
driver, fluorescent lamps with electronic ballast and fluorescent
lamps with inductive circuits or inductively compensated circuits. The
device may not be used in circuits having orientation lights (neon
lamp) combined with energy saving lamps.
Use for purposes other than those specified is not permitted.
The overall product must not be modified or converted in any way.
Modifications may lead to damage to the product and, in addition,
may also result in hazards such as short-circuits, fire, electric shock,
etc. All personal injury and material damage caused by inappropriate
usage is the responsibility of the operator of the product and not of
the manufacturer of the product.
Please note that incorrect operation or connection of the product
is outside of our scope of influence. Consequently, we accept no
liability whatsoever for damage caused in this way.
Scope of delivery
1 Electronic series switch ES1000W-AF8
1 Operating manual
Article designation/article number
ES1000W-AF8 / 014002001
36 mm
32 mm
20 mm
The ES1000W-AF8 electronic series switch allows separate switching
of additional lights, such as: ceiling lights and wall lights using only
a single existing 230 V circuit.
Plättner Elektronik GmbH •Lerchenbreite 8 •38889 Blankenburg
TEL. [phone] MAIL [e-mail]
FAX [phone]-199 WEB www.plaettner.com
Made in Germany, WEEE-Reg.Nr DE 61017759

Installation instructions
Electronic Series Switch ES1000W-AF8
Notes:
The currently set switching state can change after a power cut! Make sure that the
terminal connections in the circuit are secure!
Possible causes of NON function:
 •N-connectionnotcontacting
 •Bouncinglightswitch
 •CapacitancesbetweenN&L
1. Starting situation: Normal off circuit
In the existing off circuit (Figure 1) an additional lamp (lamp B) is to be installed
and is to be separately switchable (while retaining the existing off switch and the
existing electrical installation). This is very easy with the ES1000W-AF8 as explained
below.
Circuit version SV1
2.CircuitextensionusingtheES1000W-AF8inswitch-onmode
For installing the ES1000W-AF8, the circuit shown in Figure 1 remains unchanged.
However, the circuit is extended by wiring the ES1000W-AF8 in accordance with
Figure 2 – Switching on. The use of a 4-way plug terminal is recommended for the
N connection. Lamp A is used most of all since this is always switched on when the
switch is actuated.
2.1. Function of the ES1000W-AF8 in switch-on mode
Closing the switch switches on lamp A. Lamp B remains switched off. When actuat-
ing the switch again (switching off and on again within 1-2 sec.), lamp A remains
switched on and lamp B is switched on at the same time.
Actuating the switch once again (switching off and on again within 1-2 sec.)
switches off lamp B again. Lamp A remains on.
If the switch remains switched off for longer than 2 seconds, the ES1000W-AF8
returns to its basic state. Switching on again results in switching state 1 again, as
shown in Table 1.
Switch-on mode
LampA
LampB
1. Regular swiching on
(basic state after
break time > 2 sec.)
ON OFF
2. Short
swiching off-on
( < 2 sec.)
ON OFF
3. Short
swiching off-on
( < 2 sec.)
(swiching condition 1)
ON OFF
4. Short
swiching off-on
( < 2 sec.)
ON OFF
Figure 1
Figure 2 - Switch-on mode
Table 1
L
N
A
230 V
230 V
~ AC
~ AC
swich
swich
ES1000 W-AF8
L
B
A
LLS1 LS2 N
N
4-way plug terminal

Circuit version SV2
3.CircuitextensionusingtheES1000W-AF8inswitch-offmode
For installing the ES1000W-AF8, the circuit shown in Figure 1 remains unchanged.
However, the circuit is extended by wiring the ES1000W-AF8 in accordance with
Figure 3 – Switching off.
The use of a 4-way plug terminal is recommended for the N connection. Lamp A
is used most of all since this is always switched on when the switch is actuated.
3.1 Function of the ES1000W-AF8 in switch-off mode
Closing the switch switches on lamp A. Lamp B is also switched on. When actuat-
ing the switch again (switching off and on again within 1-2 sec.), lamp A remains
switched on and lamp B is switched off at the same time.
Actuating the switch once again (switching off and on again within 1-2 sec.) switch-
es on lamp B again. Lamp A remains on.
If the switch remains switched off for longer than 2 seconds, the ES1000W-AF8
returns to its basic state. Switching on again results in switching state 1 again, as
shown in Table 2.
Circuit version SV3
4.CircuitextensionusingtheES1000W-AF8inswitch-overmode
For installing the ES1000W-AF8, the circuit shown in Figure 1 must be changed. The
wiring for this is depicted in Figure 4 – Switching over.
The use of a 4-way plug terminal is recommended for the N connection. The lamp
that is most frequently used is to be wired to connection LS1 because this is the
first to be switched on when the switch is actuated. This is lamp B in the example.
4.1. Function of the ES1000W-AF8 in switch-over mode
Closing the switch switches on lamp B. Lamp A remains switched off. When actuat-
ing the switch again (switching off and on again within 1-2 sec.), lamp B is switched
off and lamp A is switched on at the same time.
Actuating the switch once again (switching off and on again within 1-2 sec.) switch-
es off lamp A again. Lamp B is switched on.
If the switch remains switched off for longer than 2 seconds, the ES1000W-AF8
returns to its basic state. Switching on again results in switching state 1 again, as
shown in Table 3.
Switch-on mode
LampA
LampB
1. Regular swiching on
(basic state after
break time > 2 sec.)
ON ON
2. Short
swiching off-on
( < 2 sec.)
ON OFF
3. Short
swiching off-on
( < 2 sec.)
(swiching condition 1)
ON ON
4. Short
swiching off-on
( < 2 sec.)
ON OFF
Switch-on mode
LampA
LampB
1. Regular swiching on
(basic state after
break time > 2 sec.)
OFF ON
2. Short
swiching off-on
( < 2 sec.)
ON OFF
3. Short
swiching off-on
( < 2 sec.)
(swiching condition 1)
OFF ON
4. Short
swiching off-on
( < 2 sec.)
ON OFF
Table 2
Table 3
Figure 4 - Switch-over mode
230 V ~ AC
swich
ES1000 W-AF8
L
B
A
LLS1 LS2 N
N
Figure 3 - Switch-off mode
230 V ~ AC
swich
4-way plug terminal
ES1000 W-AF8
L
B
A
LLS1 LS2 N
N
4-way plug terminal

Guarantee conditions
Electronic Series Switch ES1000W-AF8
Manufacturer’s guarantee conditions
1. The guarantee is only valid in combination with the original in-
voice, sales receipt or a confirmation of the guarantee period
from PE. The repair or replacement of the device or of individual
parts does not result in an extension or renewal of the guarantee
period.
2. The decision to repair or replace a faulty device or component
parts shall be taken at the sole discretion of PE. The relevant re-
placed device or component part shall then become the property
of PE.
3. PE attaches great importance to good service which ensures that
repairs are to be carried out quickly and reliably. For this reason,
all guarantee repairs shall be carried out by PE itself or by ap-
pointed specialist dealers. If repairs are carried out during the
guarantee period by parties who are not authorised or appoint-
ed, the guarantee shall become null and void.
4. After the end customer has reported the fault, the faulty device
shall be replaced with a comparable model once PE has granted
its approval for replacement. This replacement device becomes
the property of the end customer only after the faulty device has
been handed over and only if the guarantee claim is not rejected
within 4 weeks of the faulty device being handed over to PE. The
faulty device is to be handed over without delay, within five (5)
working days at the latest. Otherwise the end customer shall be
charged for the replacement device in accordance with the cur-
rent end consumer price.
5. The guarantee from PE does not include the following items:
a) Routine checking, maintenance and repair, and the replacement
of wearing parts
b) Faults that have resulted from incorrect operation or incorrect
installation
c) Damage caused by storms, water, fire, surge voltage, force ma-
jeure or war, incorrect connection to the power supply, insuffi-
cient ventilation or other causes that PE has no influence upon.
d) Use of the product outside of the scope of the product specifica-
tion (only to be used for lighting purposes)
e) Incorrect mounting or installation
f) Damage caused by transport or by inappropriate packaging
g)Products with no series number or where the series number has
been changed, deleted, removed or otherwise rendered illegible.
The guarantee period has no bearing whatsoever on customers’
statutory guarantee entitlements or other contractual entitle-
ments from dealers and does not limit these entitlements in any
manner.
In the case of complaints or claims regarding faults that fall within
the scope of these guarantee exclusions, PE reserves the right to
charge the customer for any costs that may arise from these com-
plaints or claims.
PE and its distributors are not liable – to the extent permitted by law
– for direct or indirect damages or losses. Claims for compensation
for damages based on this guarantee are excluded to the extent
permitted by law.
Safety requirements
Always disconnect the power supply before carrying out installa-
tion or maintenance. Avoid high ambient temperatures. The safety
information and technical specifications must be strictly adhered to.
The installation must be performed by trained personnel, e.g. em-
ployees of an electrical installation company (electricians as per DIN
VDE 1000-10).
Protect the product against dust, moisture and splashes. The
ES1000W-AF8 may only be installed in other housings such as balda-
chines or junction boxes etc.
During installation, care must be taken to ensure that the connec-
tion wires are not subjected to mechanical stresses. When using the
device in existing circuits, ensure that the previous installation is
in a standards-conformant state (non-intact terminals, bouncing
switches). The unblocking mechanism must be used when removing
the wires.
Thank you for choosing this product. We are sure that your new
device will provide you with a lot of enjoyment in the coming years.
Plättner Elektronik GmbH (PE) provides a guarantee of 24 months
from the date of purchase for this product. If a change of owner-
ship takes place due to the product being sold on, the guarantee
shall be based on the remaining guarantee period from the date of
initial purchase. The validity period varies from country to country
depending on the locally applicable laws. For example, a period of
just one (1) year applies in Great Britain. In the case of products
with a guarantee period of over two (2) years, guarantee claims
or other questions relating to the guarantee that arise after the
two (2) years have expired should be addressed directly to PE or its
distributors. The address and telephone number can be found at
www.plaettner.com.

Max. total current 10 A through terminal L
(total for both lamps)
Grid connection 220V-240V AC / 50Hz
Weight 22 grams
Housing dimensions 36 x 32 x 20 mm (LxWxH)
Wire cross-section max. 1,5 mm2
(solid wire)
Protection degree IP 20
Ambient temperature Up to +25°C (max. 35°C)
Storage temperature 0°C to +40°C
Installation The ES1000W-AF8 can be wired into
the 10A circuit without an
additional fuse.
Operating consumption < 0.5 W
(only when switched on)
The contents of this operating manual are subject to errors and technical modifications. © Plättner Elektronik GmbH 2014 - Rev. 1.2
The current version of this operating manual can be downloaded from www.plaettner.com.
Technical data
Electronic Series Switch ES1000W-AF8
Pictue ES1000W-AF8
Distributed by:
Disposal
This electrical device must NOT be disposed of in the household waste. To dispose of it in a proper manner, please contact the public waste
collection points in your municipality. Your municipal authority will provide information on the location of these collection points, on any
applicable limits on the amount of waste that they will accept each day/month/year and on the costs that may apply if the waste is col-
lected from your home.
Our general terms of delivery for electronics products and services
can be viewed at www.plaettner.com or requested by telephone.