Playcore BigToys Navigator Series User manual

Issued/Revised:
SHEET 1 OF 5
09/20/17
BT407 NINA
Play Systems
1-866-814-8697 bigtoys.com
Parts List
PART NUMBER
QTYDESCRIPTION
BT4621SWOOP CLIMB
BT4681
TWISTED TRIDENT
BT4701
SUSPENDED PLAYSHELL
BT477
1HELIX SPINNER
3115362
SINGLE DISK CABLE
3115501DOUBLE DISK CABLE
4040301
UPRIGHT 1
4055031
UPRIGHT 2
4055051UPRIGHT 3
3116451
311349*35" POST TOP COVER
812049*
6
3/8" x 1/2" P.B.H.C.S. w/PATCH
817451*
6
3/4" ID BRONZE BEARING
HARDWARE COMPLETE
Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.
INSTALLATION INSTRUCTIONS:
1. Dig footing holes as shown in Ground Plan. See specific installation sheets for Elevation Views.
2. Refer to specific installation sheets for component attachments, hardware, details, and concrete requirements.
3. Attach 5" Post Top Cover to Uprights using 3/8" x 1/2" P.B.H.C.S. w/Patch. See Detail 612.
4. Attach Single Disk Cabe and Double Disk Cable to Tabs located on Uprights. See Detail 355.
5. Plumb and level the entire assembly and tighten all fasteners.
6. After entire discrete unit is assembled pour concrete footings within 4" to the top and taper away from post for water drainage. Allow
to cure at least 48 hours before use. NOTE: Temporary bracing may be required until concrete cures.
7. When the structure is finished and satisfactory, eliminate sharp points and sharp edges (burring) on installed hardware like bolt,
nuts, etc. Install resilient surfacing material within the use zone of play structure in accordance with ASTM specifications F1292
appropriate for the fall height of each structure. Refer to the safety guidelines.
MAINTENANCE PROCEDURE:
Periodically check hardware for tightness, and tighten as necessary. Always check all parts for breakage or wear, and immediately
put equipment out of service until any faulty parts found are repaired or replaced. Also Check all metal parts for rust, paint loss and
touch-up if necessary with paint. Check for welded areas and verify integrity. Check periodically resilient surfacing for appropriate
depth and remove extraneous materials that could cause injury, infection, or disease. Maintain detailed installation, inspection,
maintenance, and repair records for each public-use playground equipment.

SHEET 2 OF 5
09/20/17
BT407 NINA
Play Systems
1-866-814-8697 bigtoys.com
FINISHED ASSEMBLY
=INSTALLATION DETAIL
5" POST TOP COVER
(311349)
UPRIGHT 1
(404030)
UPRIGHT 2
(405503)
DOUBLE DISK CABLE
(311550)
TWISTED TRIDENT
(BT468)
SINGLE DISK CABLE
(311536)
UPRIGHT 3
(405505)
SUSPENDED PLAYSHELL
(BT470)
SINGLE DISK CABLE
(311536)
355
SWOOP CLIMB
(BT462)
HELIX SPINNER
(BT477)

SHEET 3 OF 5
09/20/17
BT407 NINA
Play Systems
1-866-814-8697 bigtoys.com
PLAN VIEW
DOUBLE DISK CABLE
(311550)
UPRIGHT 1
(404030)
TWISTED TRIDENT
(BT468)
SINGLE DISK CABLE
(311536)
SINGLE DISK CABLE
(311536)
SUSPENDED
PLAYSHELL
(BT470)
SWOOP CLIMB
(BT462)
UPRIGHT 2
(405503)
UPRIGHT 3
(405505)
HELIX SPINNER
(BT477)

SHEET 4 OF 5
09/20/17
BT407 NINA
Play Systems
1-866-814-8697 bigtoys.com
9
3
6
10 11
8
1
5
7
2
4
GROUND PLAN
Horizontal Dim.
Vertical Dim.
194 3/4 in
[494.68 cm]
FOOTING TABLE
Hole No. Hor. Dim. Ver. Dim. Diagonal
100 0
278 1/8" 19 11/16" 80 9/16"
391 3/4" 19 5/16" 93 3/4"
484 11/16" 37 3/8" 92 9/16"
55/16" 44 3/4" 44 7/8"
623 11/16" 86 3/8" 89 9/16"
724 5/16" 86 3/8" 89 11/16"
865 3/4" 101 7/16" 120 7/8"
958 11/16" 115 15/16" 129 15/16"
10 17 7/8" 138 5/8" 139 3/4"
11 18 9/16" 138 5/8" 139 13/16"
156 5/8 in
[397.75 cm]

SHEET 5 OF 5
09/20/17
BT407 NINA
2
1
34
2
5
1
CM
0
INCH0
10961114815
712 13
4
365
1-866-814-8697 bigtoys.com
612
UPRIGHT
5" POST TOP COVER
(311349)
355
PIN
*LOCTITE (SUPPLIED BY
OTHERS) SHOULD BE
USED ON ANY NON-PATCH
HARDWARE.
3/4" I.D. BRONZE
WASHER (817451)
TAB
CABLE
3/8" x 1/2" P.B.H.C.S.
w/PATCH (812049)

Parts List
PART NUMBER
QTYDESCRIPTION
3113951METAL CLIMBER
3113971
3113502SHROUD
8120834
1/4" x 1 1/4" P.B.H.C.S.
817408
4
1/4" FLAT WASHER (5/8" O.D.)
8010512
3/8" x 5 3/4" HEX HEAD BOLT
817410
4
3/8" FLAT WASHER
8043532
3/8" LOCK NUT
HARDWARE COMPLETE
Issued/Revised:
SHEET 1 OF 4
BT462 SWOOP CLIMB
1-866-814-8697 bigtoys.com
2/21/2012
*Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.
INSTALLATION INSTRUCTIONS:
1. Dig footing holes as shown in Elevation and Plan Views. Refer to Top View for correct Upright and orientation.
2. Attach Metal Climber to Uprights using 3/8" x 5 3/4" Hex Head Bolt, 3/8" Flat Washer, and 3/8" Lock Nut. See Detail 601.
3. Attach Shroud to Upright using 1/4" x 1 1/4" P.B.H.C.S and 1/4" Flat Washer (5/8" O.D.). See Detail 603.
4. Plumb and level the entire assembly and tighten all fasteners.
IMPORTANT! Avoid creating any gaps between the components which fall between 3-1/2" and 9". It has been shown that such
gaps create entrapment points which can trap a child and cause injury.
5. After entire unit is assembled pour concrete footings within 4” to the top and taper away from post for water drainage. Allow to cure at
least 48 hours before use. Temporary bracing may be required until concrete cures.
6. When the structure is finished and satisfactory, eliminate sharp points and sharp edges (burring) on installed hardware like bolts, nuts,
etc. Install resilient surfacing material within the use zone of play structure in accordance with ASTM specifications F1292 appropriate for
the fall height of each structure. Refer to the safety guidelines.
MAINTENANCE PROCEDURE:
Periodically check hardware for tightness, and tighten as necessary. Always check all parts for breakage or wear, and immediately
put equipment out of service until any faulty parts found are repaired or replaced. Also Check all metal parts for rust, paint loss and
touch-up if necessary with paint. Check for welded areas and verify integrity. Check periodically resilient surfacing for appropriate
depth and remove extraneous materials that could cause injury, infection, or disease. Maintain detailed installation, inspection,
maintenance, and repair records for each public-use playground equipment.

Issued/Revised:
SHEET 2 OF 4
BT462 SWOOP CLIMB
1-866-814-8697 bigtoys.com
2/21/2012
=INSTALLATION DETAIL FINISHED ASSEMBLY COMPONENTS SHOWN IN
HIDDEN LINES ARE SOLD SEPARATELY
METAL CLIMBER
(311395)
SHROUD (311350)
603
601
UNDERNEATH

Issued/Revised:
SHEET 3 OF 4
BT462 SWOOP CLIMB
1-866-814-8697 bigtoys.com
2/21/2012
CONCRETE REQUIRED
0.218 CUBIC YARDS
[0.166 CUBIC METERS]
ELEVATION VIEW
PLAN VIEW
48 15/16 in
[124.33 cm]
30 in
[76.20 cm]
10 in
[25.40 cm]
48 in
[121.92 cm]
REF.
5 3/4 in
[14.61 cm]
36 1/2 in
[92.71 cm]
52 1/4 in
[132.72 cm]
52 9/16 in
[133.52 cm]
--- RESILIENT SURFACE---
20 in
[50.80 cm]
18 in
[45.72 cm]
REF.
18 in
[45.72 cm]
TYP.
BRICK OR EQUIVALENT

Issued/Revised:
SHEET 4 OF 4
BT462 SWOOP CLIMBER
2
1
34
2
5
1
CM
0
INCH0
10961114815
712 13
4
365
1-866-814-8697 bigtoys.com
2/21/2012
601
CLIMBER
UPRIGHT
3/8" FLAT WASHER
(817410)
3/8" x 5 3/4" HEX
HEAD BOLT (801051)
3/8" LOCK NUT
(804353)
3/8" FLAT WASHER
(817410)
603
1/4" x 1 1/4"
P.B.H.C.S. (812083)
1/4" FLAT WASHER
(5/8" O.D.) (817408)
SHROUD (311350)

Parts List
PART NUMBER
QTYDESCRIPTION
3114631WAVE ARCH CLIMBER
3115131
3113502SHROUD
8120834
1/4" x 1 1/4" P.B.H.C.S.
817408
4
1/4" FLAT WASHER (5/8" O.D.)
8010512
3/8" x 5 3/4" HEX HEAD BOLT
8174104
3/8" FLAT WASHER
8043532
3/8" LOCK NUT
HARDWARE COMPLETE
Issued/Revised:
SHEET 1 OF 4
BT468 TWISTED TRIDENT
1-866-814-8697 bigtoys.com
2/21/2012
*Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.
INSTALLATION INSTRUCTIONS:
1. Dig footing holes as shown in Elevation and Plan Views. Refer to Top View for correct Upright and orientation.
2. Attach Wave Arch to Upright using 3/8" x 5 3/4" Hex Head Bolt, 3/8" Flat Washer and 3/8" Lock Nut. See Detail 601.
3. Attach Shroud to Uprights using 1/4" x 1 1/4" P.B.H.C.S and 1/4" Flat Washer (5/8" O.D.). See Detail 603.
4. Plumb and level the entire assembly and tighten all fasteners.
IMPORTANT! Avoid creating any gaps between the components which fall between 3 1/2" and 9". It has been shown that such
gaps create entrapment points which can trap a child and cause injury.
5. After entire unit is assembled pour concrete footings within 4” to the top and taper away from post for water drainage. Allow to cure at
least 48 hours before use. Temporary bracing may be required until concrete cures.
6. When the structure is finished and satisfactory, eliminate sharp points and sharp edges (burring) on installed hardware like bolts, nuts,
etc. Install resilient surfacing material within the use zone of play structure in accordance with ASTM specifications F1292 appropriate for
the fall height of each structure. Refer to the safety guidelines. Ø
MAINTENANCE PROCEDURE:
Periodically check hardware for tightness, and tighten as necessary. Always check all parts for breakage or wear, and immediately
put equipment out of service until any faulty parts found are repaired or replaced. Also Check all metal parts for rust, paint loss and
touch-up if necessary with paint. Check for welded areas and verify integrity. Check periodically resilient surfacing for appropriate
depth and remove extraneous materials that could cause injury, infection, or disease. Maintain detailed installation, inspection,
maintenance, and repair records for each public-use playground equipment.

Issued/Revised:
SHEET 2 OF 4
BT468 TWISTED TRIDENT
1-866-814-8697 bigtoys.com
2/21/2012
= INSTALLATION DETAIL FINISHED ASSEMBLY COMPONENTS SHOWN IN
HIDDEN LINES ARE SOLD SEPARATELY
SHROUD (311350)
WAVE ARHC CLIMBER
(311463)
601
UNDERNEATH
603

Issued/Revised:
SHEET 3 OF 4
BT468 TWISTED TRIDENT
1-866-814-8697 bigtoys.com
2/21/2012
PLAN VIEW
ELEVATION VIEW
65 in
[165.06 cm]
84 5/8 in
[214.95 cm]
79 5/8 in
[202.25 cm]
81 1/8 in
[206.05 cm]
18 in
[45.72 cm]
(2 PLCS)
18 in
[45.72 cm]
REF.
CONCRETE REQUIRED
0.218 CUBIC YARDS
0.166 [CUBIC METERS]
--- RESILIENT SURFACE ---
30 in
[76.20 cm]
10 in
[25.40 cm]
20 in
[50.80 cm]
BRICK OR EQUIVALENT

Issued/Revised:
SHEET 4 OF 4
BT468 TWISTED TRIDENT
2
1
34
2
5
1
CM
0
INCH0
10961114815
712 13
4
365
1-866-814-8697 bigtoys.com
2/21/2012
601
CLIMBER
UPRIGHT
3/8" FLAT WASHER
(817410)
3/8" x 5 3/4" HEX
HEAD BOLT (801051)
3/8" LOCK NUT
(804353)
3/8" FLAT WASHER
(817410)
603
SHROUD (311350)
1/4" x 1 1/4"
P.B.H.C.S. (812083)
1/4" FLAT WASHER
(5/8" O.D.) (817408)

Issued/Revised:
SHEET 1 OF 4
BT470 SUSPENDED PLAYSHELL
1-866-814-8697 bigtoys.com
2/28/2012
Parts List
PART NUMBER
QTYDESCRIPTION
4015492
PLAYSHELL
402415
4
PLAYSHELL PIPE
3115681
309082*414 15/16" CABLE
309083*
4
20 15/16" CABLE
402250*
8
STOP CASTING ASSEMBLY
817451*323/4" ID BRONZE BEARING
HARDWARE COMPLETE
Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.
INSTALLATION INSTRUCTIONS:
1. Dig footing holes as shown in Elevation and Plain Views. Refer to Top View for correct Upright and orientation.
2. Locate Playshell and connect Playshell Pipe using Playshell Stop Casting Ass'y. See Detail 001.
3. Attach 14 15/16" Cable to Playshell. See Detail 003. NOTE: See Finished View for correct cable location.
4. On other side of Playshell attach 20 15/16" Cable to Playshell. See Detail 003. NOTE: See Finished View for correct cable location.
5. Attach 14 15/16" Cable to Tabs located on Uprights. See Detail 355. NOTE: See Finished View for correct cable location.
6. Attach 20 15/16" Cable to Tabs located on Uprights. See Detail 355. NOTE: See Finished View for correct cable location.
7. Plumb and level the entire assembly and tighten all fasteners.
8. After entire unit is assembled pour concrete footings within 4" to the top and taper away from post for water drainage. Allow to cure at
least 48 hours before use. Temporary bracing may be required until concrete cures.
9. When the structure is finished and satisfactory, eliminate sharp points and sharp edges (burring) on installed hardware like bolts,
nuts, etc. Install resilent surfacing material within the use zone of play structure in accordance with ASTM specifications F1292
appropriate for the fall height of each structure. Refer to the safety guidelines.
MAINTENANCE PROCEDURE:
Periodically check hardware for tightness, and tighten as necessary. Always check all parts for breakage or wear, and immediately
put equipment out of service until any faulty parts found are repaired or replaced. Also Check all metal parts for rust, paint loss and
touch-up if necessary with paint. Check for welded areas and verify integrity. Check periodically resilient surfacing for appropriate
depth and remove extraneous materials that could cause injury, infection, or disease. Maintain detailed installation, inspection,
maintenance, and repair records for each public-use playground equipment.

Issued/Revised:
SHEET 2 OF 4
BT470 SUSPENDED PLAYSHELL
1-866-814-8697 bigtoys.com
2/28/2012
FINISHED ASSEMBLY
355
355
001
PLAYSHELL (401549)
PLAYSHELL (401549)
= INSTALLATION DETAIL
14 15/16" CABLE
(309082)
20 15/16" CABLE
(309083)
20 15/16" CABLE
(309083)
14 15/16" CABLE
(309082)
003
003
14 15/16" CABLE
(309082)
20 15/16" CABLE
(309083)
14 15/16" CABLE
(309082)
20 15/16" CABLE
(309083)
PLAYSHELL STOP CASTING ASS'Y
(402250)
COMPONENTS SHOWN IN
HIDDEN LINES ARE SOLD SEPARATELY

Issued/Revised:
SHEET 3 OF 4
BT470 SUSPENDED PLAYSHELL
1-866-814-8697 bigtoys.com
2/28/2012
RESILIENT
SURFACE
10 in
[25.40 cm]
26 3/4 in
[67.95 cm]
30 in
[76.20 cm]
66 1/4 in
[168.28 cm]
PLAN VIEW
ELEVATION VIEW
48 in
[121.92 cm]
48 in
[121.92 cm]
18 in
[45.72 cm]
TYP.
20 in
[50.80 cm]
BRICK OR EQUIVALENT

Issued/Revised:
SHEET 4 OF 4
BT470 SUSPENDED PLAYSHELL
2
1
34
2
5
1
CM
0
INCH0
10961114815
712 13
4
365
1-866-814-8697 bigtoys.com
2/28/2012
001
PLAYSHELL
PLAYSHELL PIPE
(402415)
355
PIN
*LOCTITE (SUPPLIED BY
OTHERS) SHOULD BE
USED ON ANY NON-PATCH
HARDWARE.
3/4" I.D. BRONZE
WASHER (817451)
TAB
CABLE
003
3/4" ID BRONZE
BEARING (817451)
TAB
CABLE
3/4" ID BRONZE
BEARING (817451)
PIN
*LOCTITE (SUPPLIED BY
OTHERS) SHOULD BE USED
ON ANY NON-PATCH
HARDWARE.
1/2" x 1/2"
SET SCREW
PLAYSHELL STOP CASTING ASS'Y
(402250)

Issued/Revised:
SHEET 1 OF 6
8/28/2017
BT477 HELIX SPINNER
Play Systems
1-866-814-8697 bigtoys.com
Parts List
PART NUMBER
QTYDESCRIPTION
3096571
BOTTOM PIPE
3144871CAGE
3096731
BEARING ASSEMBLY
3098361
LOCK PLATE
3113504
SHROUD
3144321
TOP FRAME ASSEMBLY
3144891
2125872
UHMW HALF CUP
81208381/4" x 1 1/4" P.B.H.C.S.
8174088
1/4" FLAT WASHER (5/8" O.D.)
81205063/8" x 1" P.B.H.C.S. w/PATCH
8110581
3/8" x 2 3/4" B.H.C.S.
80105143/8" x 5 3/4" HEX HEAD BOLT
8043538
3/8" LOCK NUT
80480413/8" BARREL NUT
8173343
3/8" LOCK WASHER
817410163/8" FLAT WASHER
1350381
1/2" ANCHOR ROD
HARDWARE COMPLETE
*Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.

Issued/Revised:
SHEET 2 OF 6
8/28/2017
BT477 HELIX SPINNER
Play Systems
1-866-814-8697 bigtoys.com
INSTALLATION INSTRUCTIONS:
1. Dig footing holes as shown in Elevation and Plan Views. Refer to Top View for correct Upright and orientation.
2. Attach Top Frame Assembly to Upright using 3/8" x 5 3/4" Hex Head Bolt, 3/8" Flat Washer, and 3/8" Lock Nut. See Detail 601.
3. Attach Shroud to Upright using 1/4" x 1 1/4" P.B.H.C.S. and 1/4" Flat Washer (5/8" O.D.). See Detail 603.
4. Attach UHMW Half Cups to Cage using 3/8'' x 2 3/4'' B.H.C.S., 3/8'' Lock Washer, and 3/8'' Barrel Nut. See Detail 697.
5. Attach Bottom Pipe to Bearing Assembly using 3/8" x 1" P.B.H.C.S. w/Patch, 3/8” Lock Washer, and Lock Plate. See Detail 425.
6. Attach Bearing Assembly to Cage using 3/8" x 1" P.B.H.C.S. w/Patch, 3/8” Flat Washer, and 3/8” Lock Nut. See Detail 426.
7. Attach the Anchor Rod to the Bottom Pipe and place in footing hole. See Detail 231. Important; Make sure the cage is tilted
3 degrees as shown in the elevation view. Before concrete is poured check angle of cage by spinning it. The top curved pipe
socket will be aligned with bottom pipe.
8. Plumb and level the entire assembly and tighten all fasteners.
9. After entire unit is assembled, pour concrete footings within 4'' to the top and taper awat from post for water damage. Allow to cure
at least 48 hours before use. Temporary bracing may be required until concrete cures.
10. When the structure is finished and satisfactory, eliminate sharp points and sharp edges (burring) on installed hardware like bolts,
nutc, etc.. Install resilient surfacing material within the use zone of play structure in accordance with ASTM specifications F1292
appropriate for the fall height of each structure. Refer to safety guidelines.
MAINTENANCE PROCEDURE:
Periodically check hardware for tightness, and tighten as necessary. Always check all parts for breakage or wear, and immediately
put equipment out of service until any faulty parts found are repaired or replaced. Also Check all metal parts for rust, paint loss and
touch-up if necessary with paint. Check for welded areas and verify integrity. Check periodically resilient surfacing for appropriate
depth and remove extraneous materials that could cause injury, infection, or disease. Maintain detailed installation, inspection,
maintenance, and repair records for each public-use playground equipment.

Issued/Revised:
SHEET 3 OF 6
8/28/2017
BT477 HELIX SPINNER
Play Systems
1-866-814-8697 bigtoys.com
SHROUD (311350)
TOP FRAME ASSEMBLY
(314431)
LOCK PLATE (INSIDE)
(309836)
BOTTOM PIPE
(309657)
BEARING ASSEMBLY
(309673)
FINISHED ASSEMBLY
= INSTALLATION DETAIL
COMPONENTS SHOWN IN
HIDDEN LINES ARE SOLD SEPARATELY
601 603
426
425
231
UNDERNEATH
UNDERNEATH
UNDERNEATH
697
CAGE
(314487)