PLENY 301 Owner's manual

38 inches Fitness Trampoline
Assembly & User Instrucons
Visit Facebook Page @PlenyFit
Online Assembly Video
These instrucons contain important informaon which will help
you get the best from your trampoline and ensure safe and
correct assembly, use and maintenance.
Important - Please read these instrucons fully before assembly or using

1
Parts Checklist
6
Round Trampoline Bed
Handle Bar
Vertical Handrail
Flat Bottom Leg
Round Bottom Leg
Longest Lean Bottom Leg
(For Lean Trampoline Only)
1
2
3
4 5
( + put in an inner white box)
45

2
Shortest Lean Bottom Leg
A
B
C
D
X2
X2
X4
X1
In the Hardware Pack
Bolt
Washer
Fasten Bolt
X2
Allen Wrench
X2
Height Adjust Bolt
E
F
(For Lean Trampoline Only)

TM
Step 1: Pre-assembly
Assembly Instrucons
3
Remove all the wrapper and keep away from children.
Turn the Round Trampoline Bed (1) upside down on a so, non-abrasive surface.
Remove 6pcs of Plasc Caps covered on the thread head.
NOTE: Caps are just for protecon from transportaon, keep away from children and
throw it away as soon as possible.
Round Trampoline Bed 1

Handrail Clip
Handrail Clip
4
4
44
5
5
Step 2
Attach 4pcs Flat Bottom Legs (4) and 2pcs Round Bottom Legs (5) to the positions
as shown. Hand tighten only.
Note: Identify the two Handrail Clips at the edge of the Round Trampoline Bed Frame.
Make sure attach the Flat Bottom Legs (4) at this position.
Tips: Turn the trampoline back on the floor, you can use it as a normal trampoline
without Handlebar as shown.
4
Normal Trampoline
without Handle Bar

Step 3
Remove the Flat Rubber Buom from the leg (4)
at the Handrail Clip Posion.
Li the trampoline and slowly slide the
Vercal Handrail (3) up over that leg ll the end,
then put the removed flat rubber boom back
to the leg.
Hand lock it using Two Fasten Bolts (C) in the
Hardware Pack.
Do not completely ghten.
Handrail Clip
3
C
5

Align the Flat Bottom Leg (4) and Vertical
Handrail (3) as shown.
Attach the Vertical Handrail to the Handrail Clip,
using Bolt (A) and Washer (B). Tighten it using
Allen Wrench (D).
Repeat this step at the other vertical handrail.
Step 4
A
B
6

Step 5
Note: There is a Yellow Arrow Scker on the handrail
as shown, make sure it’s towards outwards.
Then insert Handle Bar (2) into Vercal Handrail.
If you have trouble to insert, slightly adjust both
Vercal Handrails towards le or right to make it
vercally.
Adjust the Handle Bar Height to fit your height,
then secure it using Height Adjust Bolt (E).
There are 3 height levels for users.
Tips: We also stampled 3 horizontal lines near the
Locking Hole. This is to help you locate the locking hole
quickly. If both le/right line is aligned to the
vercal handrail tube top, so the locking hole on both
of the handrail is aligned to each other.
locking hole
locking hole
E
7

Lean Trampoline Assembly
TM
Handrail Clip
Handrail Clip
Lean Trampoline
Step
To change it to a lean trampoline, User should remove the whole Handrail Set and all of the 6pcs
support legs first.
Then turn the bed upside down on a so, non-abrasive surface, aach the 2pcs Longest Lean
Boom Legs (6), 2pcs Round Boom Legs (5), 2pcs Shortest Lean Boom Legs (F) as exactly as
the image shown.
Note: Please idenfy X2 Handrail Clips and make sure the leg type and its posion are atached as
same as image shown.
5
5
F
6
6
8

1. One User At A Time.
2. Keep baby or pet out of your jumping area to avoid
potenally injury.
3. The Handlebar is only intended to assist User with
controlling their bounce and maintaining their balance
on the trampoline. The handlebar should NOT be used
for any other purpose or as a climbing, swing feature.
9